Engineering topics

Summerville, Brent

Publications and source records attributed to Summerville, Brent.

6 records

DOE OSTI2024

Distributed Wind Monitoring Best Practices

Accessible performance and operational data have been identified as a key enabler for distributed wind energy industry advancement. While utility-scale wind turbines benefit from reliable and continuous supervisory control and data acquisition (SCADA)-based monitoring platforms, monitoring of the U.S. fleet of distributed wind (DW) turbines has been more inconsistent, unreliable, and sometime difficult to access. Without fleet monitoring data, the industry will never understand and thus work to improve turbine under-performance and reliability issues. For the DW industry to scale up, attract investors, and boost credibility, fleetwide monitoring must be robust and reliable, select data must be made accessible to stakeholders, and the data must be in a format useful to users. To help move the industry toward a more standardized, accessible stream of monitoring data, this distributed wind monitoring best practices report attempts to cover topics including key monitoring channels, hardware, communication strategies, and accessibility. Strategic engagement with DW original equipment manufacturers (OEMs), service providers, lab and university researchers, testing organization, certification bodies, end users and solar photovoltaic (PV) monitoring experts has enabled a better understanding of the current state-of-the-art of monitoring and aided in articulating this set of best practices that will guide OEMs toward harmonized monitoring strategies, aimed at a future goal of achieving accessible performance and operational data for the entire fleet of U.S. distributed wind turbines.

17 WIND ENERGY↗

DOE OSTI2023

Modeling the Yaw Behavior of Tail Fins for Small Wind Turbines: November 22, 2021 - May 21, 2024

This report describes the aerodynamic modelling of the yaw behavior of tail fins for small wind turbines (SWTs). The analysis is based on unsteady slender body theory (USBT) and is formulated to be used with the proposed tail fin module to be added to OpenFAST. Linearized USBT, which has been applied in the past to SWT tail fins, is developed in three main ways. First, USBT is extended to high yaw angles and aspect ratios by modelling the associated nonlinear vortex dynamics and the chordwise load distribution respectively. Second, we consider the effect of time-varying wind speed. The extended theory is compared to recent unpublished measurements at the University of Perugia, Italy, for the yaw behavior of delta, elliptical, and rectangular tail fins without a rotor and nacelle. The fins were released from initial yaw angles of -40 degrees and -80 degrees ; the latter is of sufficient magnitude to show the importance of the nonlinear yaw dynamics. Further, the friction in the model tail fin bearings was measured and modelled. The constants in the aerodynamic models were taken from the literature but significant improvement in accuracy is achieved by using system identification techniques to optimize the values. This leads to the third main finding: extended USBT is accurate for all generic tail fin shapes that we considered and is, therefore, very suitable for inclusion in aeroelastic codes for SWTs. The final development is of a general nonlinear equation for yaw response that is simpler than the extended USBT and is also suitable for inclusion in OpenFAST. The two nonlinear models are used to highlight the geometric requirements for good tail fin design.

distributed wind↗

DOE OSTI2023

Improvements to the Simplified Loads Methodology in IEC 61400-2: November 22, 2021 - November 21, 2022

The "Simplified Loads Model" (SLM) of IEC 61400-2 provides a simple methodology to assess the structural integrity of a small wind turbine (SWT). The SLM is unique to the small wind turbine standard. It was included to allow SWT manufacturers with limited resources to undertake integrity checks at a reasonable cost in time and resources and avoid the expense of detailed aeroelastic simulations. Unfortunately, the SLM has gained the reputation of being overly conservative and this has reduced its value to the SWT community and its use in SWT design and certification. Conservatism in design standards is needed but excessive conservatism is not. The aim of this report is to address the principal areas of excess conservatism and recommend changes to the SLM that preserve its simplicity but reduce the excess. The changes for the ultimate loads are consistent with their treatment in aeroelastic modelling for certification and with related codes for wind loading on structures. The recommendations for a new fatigue design load case are also based on aeroelastic simulations, in this case of five SWTs of varying configurations with rated power from 2.4 to 50 kW. It is also pointed out the design load case for yawed operation omits an important term. The recommended inclusion of this term would make the SLM slightly more conservative for this case.

17 WIND ENERGY↗

DOE OSTI2023

Grand Challenges for Small Wind: Results of the European Academy Study

While modern wind turbines have become by far the largest rotating machines on Earth with further upscaling planned for the future, a renewed interest in small wind turbines (SWTs) is fostering energy transition and smart grid development. Small machines have traditionally not received the same level of aerodynamic refinement as their larger counterparts, resulting in lower efficiency, lower capacity factors, and therefore a higher cost of energy. In an effort to reduce this gap, research programs are developing worldwide. With this background, the scope of the present study is 2-fold. In the first part of this paper, an overview of the current status of the technology is presented in terms of technical maturity, diffusion, and cost. The second part of the study proposes five grand challenges that are thought to be key to fostering the development of small wind turbine technology in the near future, i.e. (1) improving energy conversion of modern SWTs through better design and control, especially in the case of turbulent wind; (2) better predicting long-term turbine performance with limited resource measurements and proving reliability; (3) improving the economic viability of small wind energy; (4) facilitating the contribution of SWTs to the energy demand and electrical system integration; (5) fostering engagement, social acceptance, and deployment for global distributed wind markets. To tackle these challenges, a series of unknowns and gaps are first identified and discussed. Based on them, improvement areas are suggested, for which 10 key enabling actions are finally proposed.

ENGINEERING,WIND ENERGY↗

DOE OSTI2023

Competitiveness Improvement Project (CIP)

Through the Competitiveness Improvement Project (CIP), the U.S. DOE supports small businesses who design and manufacture small or medium wind turbine technology through cost-shared subcontracts awarded via a competitive process. The goals of the CIP are to: improve cost competitiveness with other distributed generation technology through optimized designs and advanced manufacturing processes; increase the number of certified small and medium wind turbine designs across a wide range of sizes; and accelerate deployment of improved, certified distributed wind energy technology. NREL manages the projects through a defined period of performance subcontract, providing technical monitoring and coordinating technical assistance from DOE labs.

advanced manufacturing↗

DOE OSTI2023

Distributed Wind Aeroelastic Modeling (dWAM)

Aeroelastic modeling is the primary method for the structural and performance assessment of any wind turbine. Despite the advantages afforded by aeroelastic modeling tools, their use in the distributed wind energy industry is limited. dWAM started from the NREL Aeroelastic Modeling for Distributed Wind Turbines project with Damiani & Davis (2022) researching current needs, including input from an industry workshop. NREL's efforts will focus on OpenFAST code improvements, validation using research turbines at NREL's Flatirons Campus, code-to-code verification activities, and development of guidance documents and improved user manuals. Partner lab, Sandia National Laboratories, will focus their efforts on vertical axis wind turbine (VAWT) modeling including modeling code development, validation, and user-experience improvements.

aeroelastic↗