Engineering topics
Sumption, M. D.
Publications and source records attributed to Sumption, M. D..
A Field Quality Modeling in Canted Cosine Theta Dipole Magnets Wound Using REBCO Cables
In accelerator magnets the magnetic field quality is an important parameter. Using REBCO tapes or cables in magnet windings affects the magnetic field quality because of a quite high magnetization generated by these conductors. In this paper we analyzed numerically (using FEM) an effect of various REBCO cables’ magnetization on the field quality of canted cosine theta (CCT) dipole magnets. The magnetic properties of the cables were taken from our measurements of their M (H) curves at 4.2 K and magnetic fields up to 12 T. Also, flux creep effects were measured and their effects on field quality analyzed. Here we present a modeling of a CCT magnet containing 1 dipole double layer wound using a CORC and STAR cable. To make the FEM modeling less computationally “expensive”, we modelled only a section of 10 turns of the magnet's central part and calculated b3 fields on a circle of 2/3 of the innermost layer center line. Special M (H) curves measured during various field cycles (the so called “pre-injection cycles”) are effective in decreasing b 3 fields of the magnets. Flux creep effects suppress the b 3 fields further. In conclusion, using these techniques b 3 fields less than 10 units can be achieved.
Critical Current Densities and n-Values of MgB 2 Conductors for SMES, MRI, and Low AC Loss Applications
Multifilamentary MgB 2 strands (filament numbers 36 to 114) prepared by the in-situ power-in-tube (PIT) route with carbon doping contents of 0, 2, and 3.2% were wound on barrels for transport J c and n -value measurement at 4.2 K in fields of up to 12 T. The strand and gauge lengths were 1 m and 0.5 m. Heat treatments at 675 °C and 650 °C centered around the melting point of Mg (650 °C) and both utilized the liquid-solid reaction. A pair of strands, with and without 2% C doping exhibited the J c (B) crossover effect. Here studied were the dependencies of J c on field strength, dopant concentration, and cabling and the dependence of n -value on field strength.
Mechanism of enhanced critical fields and critical current densities of MgB2 wires with C/Dy$^{2}$O3 co-additions
A series of monofilamentary powder-in-tube MgB2 wires were fabricated with 2 mol. % C doping and co-additions of 0–3 wt. % Dy2O3. Irreversibility fields (μ0Hirr), upper critical fields (μ0Hc2), and transport critical currents were measured, and from these quantities, anisotropies (γ) and electronic diffusivities (Dπ,σ) were estimated. The addition of 1 wt. % Dy2O3 to already optimally C-doped MgB2 wires produced higher Hc2//ab, Hc2//c, and Hirr values at 4.2 K. In addition, the critical current density, Jc, increased with Dy2O3 concentration up to 1 wt. % where non-barrier Jc reached 4.35 × 104 A/cm2 at 4.2 K, 10 T. At higher temperatures, for example, 20 K and 5 T, co-additions of 2 mol. % C and 2 wt. % Dy2O3 improved non-barrier Jc by 40% and 93% compared to 2 and 3 mol. % C doping, respectively. On the other hand, measurements of Tc showed that C/Dy2O3 co-additions increase interband scattering rates at a lower rate than C doping does (assuming C doping levels giving similar levels of low-T μ0Hc2 increase as co-addition). Comparisons to a two-band model for μ0Hc2 in MgB2 allowed us to conclude that the increases in Hc2//ab, Hc2//c, and Hirr (as well as concomitant increases in high-field Jc) with Dy2O3 addition are consistent with increases primarily in intraband scattering. This suggests C/Dy2O3 co-addition to be a more promising candidate for improving non-barrier Jc of MgB2 at temperatures above 20 K.
Stability and Current Sharing in YBCO Cables – Impact of Broken Elements – FEM Modeling
Not provided.
AC losses of Roebel and CORC ® cables at higher AC magnetic fields and ramp rates
We have measured ReBCO coated conductor-based conductor on round core (CORC ® ) and Roebel cables at 77 K in a spinning magnet calorimeter, which subjected the tapes in the samples to a radial magnetic field of 566 mT (peak) at frequencies up to 120 Hz (272 T s -1 , cyclic average) with an approximately sinusoidal waveform. The samples were oriented such that the field applied to the tapes within the cables was entirely radial, simplifying subsequent analysis. An expression for loss which included hysteretic, flux creep and eddy current losses was fit to both the CORC ® and the Roebel cables. This expression allowed easy comparison of the relative influence of eddy currents and flux creep (or power-law behavior) effects. The loss of both the CORC ® and Roebel cables measured here were seen to be essentially the sum of the hysteretic loss, flux creep effects, and the normal metal eddy current losses of the individual tapes. The losses of these cables were measured at high B × d B /d t with no coupling current loss observed under the present preparation conditions. The influence of flux creep effects on loss were not negligible. The losses of the CORC ® cable per meter of tape were seen to be reduced from the case of a flat tape because of the helical geometry of the tapes.
The strong influence of Ti, Zr, Hf solutes and their oxidation on microstructure and performance of Nb 3 Sn superconductors
The strong influence of Ti, Zr, Hf solutes and their oxidation on microstructure and performance of Nb 3 Sn superconductors Over the last few years a new type of Nb 3 Sn superconducting composite based on the internal oxidation approach has emerged and has demonstrated performance significantly superior to conventional Nb 3 Sn. It requires a supply of O and the use of a Nb alloy – Nb-X, where X is a solute element that can be selectively oxidized to form oxide particles within the Nb 3 Sn. Such oxide particles not only refine Nb 3 Sn grain size, but also have the proper size to act as artificial pinning centers (APC) directly restraining fluxon motion, and thus dramatically improve superconducting properties. In this article we show that the size and volume fraction of the oxide particles determine both the levels of grain refinement and the shift in the peak field of the flux pinning force (F p -B) curve. Additionally, we explore the factors influencing these microstructure and properties, which we find include: selection of the solute element X, solute content, O content, and heat treatment. For the selection of X, we searched the periodic table for all promising candidates but focused down on the group-IVB elements (Ti, Zr, Hf) here as the drawability of Nb 3 Sn wires made from Nb-Ti, Nb-Zr, and Nb-Hf alloys has been demonstrated in the past few decades. We found that while internally oxidizing Nb-1.5at.%Ti led to negligible grain refinement and F p -B peak shift, Nb-Zr alloys led to much more dramatic results, and internally oxidizing Nb-Hf alloys led to the strongest grain refinement and F p -B peak shift. For Hf alloying in particular, we compared our internal oxidation method with another method for grain refinement, which uses Hf alloying itself without oxidation, and found that internal oxidation led to much stronger grain refinement and F p -B peak shift. We also found that higher solute content and lower reaction temperature led to stronger grain refinement and F p -B peak shift. We conclude with a discussion of the possible mechanisms for the influence of these factors.
Persistent compositions of non-stoichiometric compounds with low bulk diffusivity: A theory and application to Nb3Sn superconductors
Non-stoichiometric compounds may develop a composition gradient when they are formed by reactive diffusional processes. This paper reports an interesting phenomenon that in compounds with low bulk diffusivities, which rely mainly on grain boundary diffusion for their growth, the final bulk compositions may be far from equilibrium, with a very low bulk diffusivity leading to fixed (persistent) compositions – one such example is Nb 3 Sn, a superconductor. We investigated the microchemistry at the reactive interface using atom probe tomography to clarify the diffusion reaction mechanism for this low-bulk-diffusivity case and thus propose a theory for what determines the compound composition, using Nb 3 Sn as an example for concreteness. Using certain approximations, we derive an explicit analytical equation that illustrates what factors determine its composition profile. We compare our model with the known facts of Nb 3 Sn and see good agreement. In particular, this model predicts that internal oxidation may lead to higher Sn contents than conventional, non-oxidized Nb 3 Sn. Our measurements show that this is indeed true, and that the internally-oxidized Nb 3 Sn also has higher upper critical fields, achieving up to 28.2 T at 4.2 K. We discuss the general applicability of this model to non-stoichiometric compounds with low bulk diffusivity, and propose it as a tool to help in the design and processing of such materials for compositional control.
Stability mechanical considerations, and AC loss in HTSC monoliths, coils, and wires
For monolithic high-T(sub c) superconductors (HTSC's) calculations are presented of: (1) the initial flux jump field, H(sub fj), in melt-processed YBCO based on a field and temperature dependent J(sub c), and (2) the radial and circumferential stresses in solid and hollow cylinders containing trapped magnetic flux. For model multi filamentary (MF) HTSC/Ag strands calculations are presented of: (1) the limiting filament diameters for adiabatic and dynamic stability, and (2) the hysteretic and eddy current components of AC loss. Again for MF HTSC/Ag composite strands the need for filamentary subdivision and twisting is discussed.