Engineering topics

Sun, Cheng-Jun

Publications and source records attributed to Sun, Cheng-Jun.

At least 19 records

DOE OSTI2026

Electronegativity-Guided Site Differentiation in High-Entropy Alloy for pH-universal Hydrogen Evolution Reactions

Enhancing the intrinsic activity of transition metal catalysts for the hydrogen evolution reaction (HER) remains a critical challenge in sustainable energy conversion. Herein, we report an electronegativity-guided site differentiation strategy in a single-phase CoNiCuMoW high-entropy alloy (HEA) via electrodeposition by incorporating high-electronegativity 4d/5d orbital transition metals (Mo, W) into the face-centered cubic (fcc) matrix (CoNiCu). The as-synthesized HEA demonstrates exceptional HER performance in all pH conditions, delivering an outstanding overpotential of 65 mV (alkaline), 28 mV (acidic), and 155 mV (neutral) at a current density of 100 mA cm−2, showing performance comparable to commercial Pt/C and has excellent long-term stability at high current density (1 A cm−2, 1000 h). X-Ray absorption spectroscopy (XAS) and density functional theory (DFT) calculations reveal that the incorporation of Mo/W simultaneously alters the local coordination environment and induces element-dependent charge redistribution, accompanied by a system-level d-band center downshift, thereby optimizing the hydrogen binding strength across multimetallic sites. Meanwhile, oxophilic Mo/W sites lower the water dissociation energy barrier. These synergistic effects collectively enable efficient and durable pH-universal HER performance.

Wu, Yutong↗

DOE OSTI2024

Orientation-dependent structural properties during growth and growth mechanism of CoO films

The orientation-dependent local structural properties of CoO films on sapphire substrates during growth were investigated through linearly-polarized extended X-ray absorption fine structure (EXAFS) measurements. Specifically, CoO(1 1 1) and (100) crystals with a rock-salt structure (Fm3m) were epitaxially grown on alpha-Al2O3(0001) and (1012) substrates, respectively, at 700 degrees C using a radio-frequency sputtering system. The local structural properties of CoO films in the in-plane and out-of-plane orientations were quantitatively determined using linearly-polarized EXAFS at the Co K-edge during growth. The EXAFS analysis revealed that during the initial stages of growth, the local structural properties exhibit significant differences compared to thick films, with short atomic distances and large (small) Debye-Waller factors observed in the out-of-plane (in-plane) orientations. The local structural strain mostly diminished when approximately 20 CoO layers accumulated on the substrate. Density functional theory (DFT) calculations further supported these findings by confirming that cobalt atoms initially form stable bonds with the sapphire surface, leading to the simultaneous growth of oxygen and cobalt layers in a coordinated manner through layer-by-layer growth.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Polysulfide-incompatible additive suppresses spatial reaction heterogeneity of Li-S batteries

Rational electrolyte engineering for practical pouch cells remains elusive because the correlation between the cathode/solid-electrolyte interphase layer and cell-level reaction behavior is poorly understood. Here, by combining multiscale characterization and computational modeling, we show that—counter to the conventional perception of polysulfide-incompatible additives—the spontaneous reaction of sparingly solvated polysulfides with Lewis acid additives (LAAs) can induce in situ formation of a homogeneous interphase on thick and tortuous S cathode. Multiscale synchrotron X-ray characterization consistently affirms that such interface design could effectively eliminate the notorious problems of polysulfide shuttle and lithium corrosion and, more importantly, provide an interconnected “ion transport highway” to alleviate the uneven ion transport within the tortuous S cathode. Hence, this design dramatically reduces the reaction heterogeneity of lithium-sulfur (Li-S) pouch cells under lean electrolyte conditions. Further, this work resolves controversy around the role of polysulfide-incompatible additives in high-energy Li-S pouch cells and highlights the importance of suppressing reaction heterogeneity for practical batteries.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Solvent-mediated oxide hydrogenation in layered cathodes

Self-discharge and chemically induced mechanical effects degrade calendar and cycle life in intercalation-based electrochromic and electrochemical energy storage devices. In rechargeable lithium-ion batteries, self-discharge in cathodes causes voltage and capacity loss over time. The prevailing self-discharge model centers on the diffusion of lithium ions from the electrolyte into the cathode. Here, we demonstrate an alternative pathway, where hydrogenation of layered transition metal oxide cathodes induces self-discharge through hydrogen transfer from carbonate solvents to delithiated oxides. In self-discharged cathodes, we further observe opposing proton and lithium ion concentration gradients, which contribute to chemical and structural heterogeneities within delithiated cathodes, accelerating degradation. Hydrogenation occurring in delithiated cathodes may affect the chemo-mechanical coupling of layered cathodes as well as the calendar life of lithium-ion batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

Sustainable layered cathode with suppressed phase transition for long-life sodium-ion batteries

Sodium-ion batteries are among the most promising alternatives to lithium-based technologies for grid and other energy storage applications due to their cost benefits and sustainable resource supply. For the cathode—the component that largely determines the energy density of a sodium-ion battery cell—one major category of materials is P2-type layered oxides. Unfortunately, at high state-of-charge, such materials tend to undergo a phase transition with a very large volume change and consequent structural degradation during long-term cycling. Here we address this issue by introducing vacancies into the transition metal layer of P2-Na$_{0.7}$Fe$_{0.1}$Mn$_{0.75\square}$$_{0.15}$O2 (‘$_{\square}$’ represents a vacancy). The transition metal vacancy serves to suppress migration of neighbouring Na ions and therefore maintain structural and thermal stability in Na-depleted states. Moreover, the specific Na-O-$_{\square}$ configuration triggers a reversible anionic redox reaction and boosts the energy density. As a result, the cathode design here enables pouch cells with energy densities of 170 Wh kg -1 and 120 Wh kg -1 that can operate for over 600 and 1,000 cycles, respectively. In conclusion, our work not only suggests a feasible strategy for cathode design but also confirms the possibility of developing a battery chemistry that features a reduced need for critical raw materials.

25 ENERGY STORAGE↗

DOE OSTI2024

Achieving a high-performance sodium-ion pouch cell by regulating intergrowth structures in a layered oxide cathode with anionic redox

In P2-type layered transition metal (TM) oxides, which are typical cathode materials for Na-ion batteries, the presence of Li within the TM layer could lead to the formation of specific Na–O–Li configurations that trigger additional oxygen redox at high charging voltages. However, the prismatic-type (P-type) to octahedral-type (O-type) phase transition and irreversible TM migration could be simultaneously aggravated in high state of charge, resulting in structural distortion. Here we demonstrate that excessive desodiation of P2-Na 0.67 Li 0.1 Fe 0.37 Mn 0.53 O 2 (NLFMO) induces the formation of neighbouring O-type stacking faults with an intergrowth structure (that is, interlacing of O- and P-type layers), which leads to out-of-lattice Li migration and irreversible oxygen loss. We show that, by controlling the depth of charge to tailor the intergrowth structure, a P-type stacking state can be uniformly interspersed between the O-type stacking state, thereby avoiding neighbouring O-type stacking faults. Adjusting the O/P intergrowth structure leads to both reversible migration of Li/TM ions and reversible anionic redox in the NLFMO cathode. In conclusion, we thereby achieve a high-performance pouch cell (with an energy density of 165 W h kg −1 based on the entire weight of the cell) with both cationic and anionic redox activities.

25 ENERGY STORAGE↗

DOE OSTI2023

Elucidating the mechanism underlying the augmented capacity of MoO 2 as an anode material in Li-ion batteries

Transition-metal oxide anode materials have been observed to possess an intriguing surplus of capacity beyond the expected values based on conversion reaction. However, the mechanisms behind this phenomenon have remained contentious and elusive. Here, this study focuses on synthesized nanosized molybdenum dioxide and its electrochemical performance as an anode material for Li-ion batteries. Our findings reveal a substantial increase in capacity upon cycling, achieving approximately 1688 mA h g -1 , nearly double the theoretical capacity, after 700 cycles at a 1C rate. To elucidate the mechanisms underlying this augmented capacity, a comprehensive analysis employing in situ and ex situ X-ray diffraction, X-ray absorption spectroscopy, scanning electron microscopy, and transmission electron microscopy was conducted at various stages of the Li-ion cell cycling. Our results indicate that no conversion reaction occurs during the initial discharge phase, with Li 2 O and Mo remaining undetected. Instead, Li 0.98 MoO 2 is generated upon lithiation. Further materials characterization employing electron energy loss spectroscopy and energy-dispersive X-ray spectroscopy on the cycled electrode suggests the potential formation of a metallic Li-rich layer at the interface of the Li-ion intercalated phase subsequent to the formation of Li 0.98 MoO 2 , contributing to the surplus Li storage. Moreover, electrochemical impedance spectroscopy coupled with ex situ SEM and TEM analyses reveals that alterations in particle size and morphology, along with changes in the solid electrolyte interphase (SEI) resistance, are instrumental in the capacity variation observed upon cycling.

25 ENERGY STORAGE↗

DOE OSTI2023

Cascade electrocatalysis via AgCu single-atom alloy and Ag nanoparticles in CO 2 electroreduction toward multicarbon products

Electrocatalytic CO 2 reduction into value-added multicarbon products offers a means to close the anthropogenic carbon cycle using renewable electricity. However, the unsatisfactory catalytic selectivity for multicarbon products severely hinders the practical application of this technology. In this paper, we report a cascade AgCu single-atom and nanoparticle electrocatalyst, in which Ag nanoparticles produce CO and AgCu single-atom alloys promote C-C coupling kinetics. As a result, a Faradaic efficiency (FE) of 94 ± 4% toward multicarbon products is achieved with the as-prepared AgCu single-atom and nanoparticle catalyst under ~720 mA cm -2 working current density at -0.65 V in a flow cell with alkaline electrolyte. Density functional theory calculations further demonstrate that the high multicarbon product selectivity results from cooperation between AgCu single-atom alloys and Ag nanoparticles, wherein the Ag single-atom doping of Cu nanoparticles increases the adsorption energy of *CO on Cu sites due to the asymmetric bonding of the Cu atom to the adjacent Ag atom with a compressive strain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Visualizing interfacial collective reaction behaviour of Li–S batteries

Benefiting from high energy density (2,600 Wh kg -1 )) and low cost, lithium-sulfur (Li-S) batteries are considered promising candidates for advanced energy-storage systems. Despite tremendous efforts in suppressing the long-standing shuttle effect of lithium polysulfides, understanding of the interfacial reactions of lithium polysulfides at the nanoscale remains elusive. This is mainly because of the limitations of in situ characterization tools in tracing the liquid-solid conversion of unstable lithium polysulfides at high temporal-spatial resolution. There is an urgent need to understand the coupled phenomena inside Li-S batteries, specifically, the dynamic distribution, aggregation, deposition and dissolution of lithium polysulfides. Here, by using in situ liquid-cell electrochemical transmission electron microscopy, we directly visualized the transformation of lithium polysulfides over electrode surfaces at the atomic scale. Notably, an unexpected gathering-induced collective charge transfer of lithium polysulfides was captured on the nanocluster active-centre-immobilized surface. It further induced an instantaneous deposition of nonequilibrium Li2S nanocrystals from the dense liquid phase of lithium polysulfides. Without mediation of active centres, the reactions followed a classical single-molecule pathway, lithium polysulfides transforming into Li 2 S 2 and Li 2 S step by step. Molecular dynamics simulations indicated that the long-range electrostatic interaction between active centres and lithium polysulfides promoted the formation of a dense phase consisting of Li + and S n 2- (2 < n ≤ 6), and the collective charge transfer in the dense phase was further verified by ab initio molecular dynamics simulations. Finally, the collective interfacial reaction pathway unveils a new transformation mechanism and deepens the fundamental understanding of Li-S batteries.

25 ENERGY STORAGE↗

DOE OSTI2023

Epitaxial growth of oriented CoO films by radio-frequency sputtering deposition

Rock-salt CoO is a p-type semiconductor and its Neel temperature is close to room temperature. CoO-based compounds are known as promising systems for renewable energy harvest with high efficiency. CoO with catalytic and exchange bias properties can be widely used for industrial applications. In this paper, we report high-quality stable CoO(111) and (100) films epitaxially grown on c-cut (0001) and r-cut ($10\bar1$2) alpha-Al 2 O 3 substrates, respectively, using radio-frequency sputtering deposition. X-ray diffraction (XRD) measurements revealed that the CoO films had a rock-salt structure (Fm3m) with lattice constants of 4.2477 Å and 4.2617 Å for film grown on (0001) and ($10\bar1$2) α-Al 2 O 3 substrates, respectively. CoO films with the best crystal quality were grown at a substrate temperature of similar to ~700°C. XRD measurements of CoO(111) films indicated a lack of structural residual strain, whereas CoO(100) films had substantial amounts of structural strain. X-ray reflectivity (XRR) and transmission electron microscopy measurements showed neither oxygen vacancy nor defects in both CoO(111) and (100) films. Further, XRR revealed that the mean electron density of the CoO films was nearly identical to a pure CoO and that the films were considerably stable under the atmosphere.

36 MATERIALS SCIENCE↗

DOE OSTI2023

In situ microscopy and spectroscopy characterization of microsized Sn anode for sodium-ion batteries

Microsized Sn is a promising anode material for sodium-ion batteries in terms of cost, specific capacity, and volumetric energy density, which however suffers from huge volume changes and rapid cell degradation upon cycling. Despite recent advances via nanostructured electrode design and interface engineering, the correlation between mechanical stability, solid-electrolyte interphase (SEI) and reaction kinetics/reversibility remains controversial and elusive. Here, in this work, by combining in situ scanning electron microcopy and X-ray absorption spectroscopy as well as X-ray photoelectron spectroscopy, we have investigated the underlying electro-chemo-mechanical behavior and their coupling effects during charge/discharge of microsized Sn anode. Our results revealed that microsized Sn is pulverized into nanoparticles with simultaneous formation of numerous voids and pores upon the 1st charge/discharge, while the electrolytes composition plays a critical role on the consequent parasitic reactions and eventually the sodiation/de-sodiation reversibility. In contrast to carbonate-based electrolytes, ether-based electrolytes enabled formation of inorganic species dominated SEI with improved mechanical strength, thus leading to higher specific capacity and improved cycling stability. The present findings are crucial for future development of microsized anode materials for rechargeable batteries with high volumetric energy density.

25 ENERGY STORAGE↗

DOE OSTI2023

The AXEAP2 program for K β X-ray emission spectra analysis using artificial intelligence

The processing and analysis of synchrotron data can be a complex task, requiring specialized expertise and knowledge. Our previous work addressed the challenge of X-ray emission spectrum (XES) data processing by developing a standalone application using unsupervised machine learning. However, the task of analyzing the processed spectra remains another challenge. Although the non-resonant K β XES of 3 d transition metals are known to provide electronic structure information such as oxidation and spin state, finding appropriate parameters to match experimental data is a time-consuming and labor-intensive process. Here, a new XES data analysis method based on the genetic algorithm is demonstrated, applying it to Mn, Co and Ni oxides. This approach is also implemented as a standalone application, Argonne X-ray Emission Analysis 2 ( AXEAP2 ), which finds a set of parameters that result in a high-quality fit of the experimental spectrum with minimal intervention. AXEAP2 is able to find a set of parameters that reproduce the experimental spectrum, and provide insights into the 3 d electron spin state, 3 d –3 p electron exchange force and K β emission core-hole lifetime.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Selectively Reducing Nitrate into NH 3 in Neutral Media by PdCu Single-Atom Alloy Electrocatalysis

Electrocatalytic nitrate reduction reaction (NO 3 – RR) technology provides a promising solution to recover the nitrate nutrition from wastewater through catalyzing nitrate reduction into value-added NH 3 . However, the selectivity and efficiency of electrocatalysts are frustrated due to the imbalance of *H adsorption (for NO 3 hydrogenation) and unavoidable adjacent *H self-coupling on active sites, resulting in competitive hydrogen evolution reaction (HER). Here, we report a PdCu single-atom alloy (SAA) catalyst that allows isolated Pd sites to produce *H for the hydrogenation process of *NO 3 on neighboring Cu sites, which can restrain the *H self-coupling through extending the distance between two *H and thus effectively suppress competitive HER. Consequently, the PdCu SAA catalyst exhibits an ultrahigh NH 3 Faraday efficiency (FE) of 97.1% with a yield of 15.4 μmol cm –2 h –1 from the electrocatalytic NO 3 – RR in the neutral electrolyte, outperforming most of the reported catalysts. In conclusion, single-crystal experiments and theoretical calculations further prove that the introduction of atomic Pd on the Cu (100) surface could serve as the main active site and greatly decrease the energy barrier of the rate-determining step (RDS) on Cu from ΔG = 0.39 eV (*NOO → *NOOH) to ΔG = 0.10 eV of *NOH → *NHOH on PdCu SAA.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2023

Amino-tethering synthesis strategy toward highly accessible sub-3-nm L1 0 -PtM catalysts for high-power fuel cells

Because of the poor accessibility of embedded active sites, platinum (Pt)-based electrocatalysts suffer from insufficient Pt utilization and mass transport in membrane electrode assemblies (MEAs), limiting their performance in polymer electrolyte membrane fuel cells. Here, we report a simple and universal approach to depositing sub-3-nm L1 0 -PtM nanoparticles over external surfaces of carbon supports through pore-tailored amino (NH 2 )-modification, which enables not only excellent activity for the oxygen reduction reaction, but also enhanced Pt utilization and mass transport in MEAs. Using a low loading of 0.10 mg Pt ∙cm -2 , the MEA of PtCo/KB-NH 2 delivered an excellent mass activity of 0.691 A∙mgPt -1 , a record-high power density of 0.96 W∙cm -2 at 0.67 V, and only a 30-mV drop at 0.80 A∙cm -2 after 30,000 voltage cycles, which meets nearly all targets set by the Department of Energy. Finally, this work provides an efficient strategy for designing advanced Pt-based electrocatalysts and realizing high-power fuel cells.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2022

Fe–N–C Boosts the Stability of Supported Platinum Nanoparticles for Fuel Cells

The poor durability of Pt-based nanoparticles dispersed on carbon black is the challenge for the application of long-life polymer electrolyte fuel cells. Recent work suggests that Fe- and N-codoped carbon (Fe-N-C) might be a better support than conventional high-surface-area carbon. In this work, we find that the electrochemical surface area retention of Pt/Fe-N-C is much better than that of commercial Pt/C during potential cycling in both acidic and basic media. In situ inductively coupled plasma mass spectrometry studies indicate that the Pt dissolution rate of Pt/Fe-N-C is 3 times smaller than that of Pt/C during cycling. Density functional theory calculations further illustrate that the Fe-N-C substrate can provide strong and stable support to the Pt nanoparticles and alleviate the oxide formation by adjusting the electronic structure. The strong metal-substrate interaction, together with a lower metal dissolution rate and highly stable support, may be the reason for the significantly enhanced stability of Pt/Fe-N-C. In conclusion, this finding highlights the importance of carbon support selection to achieve a more durable Pt-based electrocatalyst for fuel cells.

25 ENERGY STORAGE↗

DOE OSTI2022

AXEAP : a software package for X-ray emission data analysis using unsupervised machine learning

The Argonne X-ray Emission Analysis Package ( AXEAP ) has been developed to calibrate and process X-ray emission spectroscopy (XES) data collected with a two-dimensional (2D) position-sensitive detector. AXEAP is designed to convert a 2D XES image into an XES spectrum in real time using both calculations and unsupervised machine learning. AXEAP is capable of making this transformation at a rate similar to data collection, allowing real-time comparisons during data collection, reducing the amount of data stored from gigabyte-sized image files to kilobyte-sized text files. With a user-friendly interface, AXEAP includes data processing for non-resonant and resonant XES images from multiple edges and elements. AXEAP is written in MATLAB and can run on common operating systems, including Linux, Windows, and MacOS.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

Effect of the grain arrangements on the thermal stability of polycrystalline nickel-rich lithium-based battery cathodes

One of the most challenging aspects of developing high-energy lithium-based batteries is the structural and (electro)chemical stability of Ni-rich active cathode materials at thermally-abused and prolonged cell cycling conditions. Here, we report in situ physicochemical characterizations to improve the fundamental understanding of the degradation mechanism of charged polycrystalline Ni-rich cathodes at elevated temperatures (e.g., ≥ 40 °C). Using multiple microscopy, scattering, thermal, and electrochemical probes, we decouple the major contributors for the thermal instability from intertwined factors. Our research work demonstrates that the grain microstructures play an essential role in the thermal stability of polycrystalline lithium-based positive battery electrodes. We also show that the oxygen release, a crucial process during battery thermal runaway, can be regulated by engineering grain arrangements. Furthermore, the grain arrangements can also modulate the macroscopic crystallographic transformation pattern and oxygen diffusion length in layered oxide cathode materials.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Atomically dispersed Pt and Fe sites and Pt–Fe nanoparticles for durable proton exchange membrane fuel cells

Proton exchange membrane fuel cells convert hydrogen and oxygen into electricity without emissions. The high cost and low durability of Pt-based electrocatalysts for the oxygen reduction reaction hinder their wide application, and the development of non-precious metal electrocatalysts is limited by their low performance. Here we design a hybrid electrocatalyst that consists of atomically dispersed Pt and Fe single atoms and Pt–Fe alloy nanoparticles. Its Pt mass activity is 3.7 times higher than that of commercial Pt/C in a fuel cell. More importantly, the fuel cell with a low Pt loading in the cathode (0.015 mg Pt cm –2 ) shows an excellent durability, with a 97% activity retention after 100,000 cycles and no noticeable current drop at 0.6 V for over 200 hours. These results highlight the importance of the synergistic effects among active sites in hybrid electrocatalysts and provide an alternative way to design more active and durable low-Pt electrocatalysts for electrochemical devices.

25 ENERGY STORAGE↗