Engineering topics

Sun, T.

Publications and source records attributed to Sun, T..

12 records

DOE OSTI2024

The Water Balance Representation in Urban‐PLUMBER Land Surface Models

Abstract Urban Land Surface Models (ULSMs) simulate energy and water exchanges between the urban surface and atmosphere. However, earlier systematic ULSM comparison projects assessed the energy balance but ignored the water balance, which is coupled to the energy balance. Here, we analyze the water balance representation in 19 ULSMs participating in the Urban‐PLUMBER project using results for 20 sites spread across a range of climates and urban form characteristics. As observations for most water fluxes are unavailable, we examine the water balance closure, flux timing, and magnitude with a score derived from seven indicators expecting better scoring models to capture the latent heat flux more accurately. We find that the water budget is only closed in 57% of the model‐site combinations assuming closure when annual total incoming fluxes (precipitation and irrigation) fluxes are within 3% of the outgoing (all other) fluxes. Results show the timing is better captured than magnitude. No ULSM has passed all water balance indicators for any site. Models passing more indicators do not capture the latent heat flux more accurately refuting our hypothesis. While output reporting inconsistencies may have negatively affected model performance, our results indicate models could be improved by explicitly verifying water balance closure and revising runoff parameterizations. By expanding ULSM evaluation to the water balance and related to latent heat flux performance, we demonstrate the benefits of evaluating processes with direct feedback mechanisms to the processes of interest.

Jongen, H. J.↗

DOE OSTI2024

Nonlinear modeling of ELM mitigation with RMP on HL-2A

Abstract Nonlinear modeling of mitigation of the edge localized mode (ELM) with resonant magnetic perturbation (RMP) is performed for the HL-2A tokamak, utilizing the three-dimensional (3D) magnetohydrodynamic code JOREK. Based on the 3D equilibrium established after application of the n = 1 ( n is the toroidal mode number) RMP at 4.9 kAt coil current with odd parity, ELM mitigation is successfully simulated consistent with the experimental result. Nonlinear simulations show strong mode coupling among toroidal Fourier harmonics, allowing redistribution of the magnetic energy such that the most unstable toroidal mode saturates at a lower level. This magnetic energy cascade offers an explanation of the RMP-induced ELM mitigation achieved in HL-2A. Detailed examination of the simulation results shows persistent resonant field screening even during the ELM mitigation phase. Finite plasma resistivity however does enable partial penetration of the resonant field thus modifying the edge magnetic topology and characteristics of the edge transport. Plasma radial profiles undergo pronounced changes around the pedestal region, when the magnetic energy of the most unstable toroidal mode reaches the maximum value. Systematic scans of the applied RMP coil current with the JOREK simulations find a threshold value of around 4.5 kAt required for achieving the ELM mitigation on HL-2A.

Physics↗

DOE OSTI2022

High strain rate deformation of aged TRIP Ti-10V-2Fe-3Al (wt.%) examined by in-situ synchrotron X-ray diffraction

Transformation Induced Plasticity (TRIP) is a promising avenue for tailoring the work hardening response of metastable $β$ titanium (Ti) alloys. Here we show that aged TRIP Ti-10V-2Fe-3Al (wt.%) maintains higher elongations and flow stresses as strain rate increases, if phase stability and microstructural characteristics are tuned. Low temperature aging influences the matrix $β$ phase stability by $ω$ phase precipitation, which affords a promising way to impact the TRIP effect and obtain desirable mechanical properties, ranging from high damping capacity to good strength/ductility combinations. Although TRIP is active during quasi-static and dynamic testing up to 2000 s –1 , increasing aging time and/or strain rate reduces the overall propensity for the TRIP effect and extent of transformation, which occurs rapidly just at the onset of yielding. Importantly, TRIP with $ω$ phase precipitation provides interesting alloying, microstructure, and property design strategies for engineering applications like lightweight protective structures, where high strains and the need for energy absorption are encountered.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Transformation and twinning induced plasticity in metastable Ti-Mo alloys under high strain rate deformation

The development of metastable titanium (Ti) alloys provides an unprecedented opportunity to expand their use in plasticity and damage critical applications like protective structures. However, such applications require knowledge of quasi-static to dynamic mechanical behavior, which is currently lacking. Here we perform in-situ, ultrafast synchrotron x-ray diffraction during high strain rate (Kolsky) pressure bar testing in tension and post-mortem electron microscopy to study TRansformation Induced Plasticity (TRIP) and TWinning Induced Plasticity (TWIP) in metastable Ti-Mo alloys. Two alloys, namely Ti-12Mo and Ti-15Mo (wt.%), were selected for study having different β -phase chemical stabilities. TWIP was observed in both Ti-12Mo and Ti-15Mo by in-situ synchrotron diffraction during high strain rate testing. Post-mortem microstructural characterization also revealed the presence of TRIP in Ti-12Mo. TWIP in Ti-15Mo was found to under-perform in terms of total elongation compared to TRIP/TWIP in Ti-12Mo. Ti-12Mo exhibited an average elongation of 17% compared to only 12% for Ti-15Mo with deformation at 1000 s -1 . In conclusion, TRIP resulted in significantly finer microstructure evolution and alleviated local strain accumulations in Ti-12Mo, suggesting TRIP can be used to tune available strength/ductility combinations in metastable Ti alloys under high strain rate deformation conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The interplay between vapour, liquid, and solid phases in laser powder bed fusion

The capability of producing complex, high performance metal parts on demand has established laser powder bed fusion (LPBF) as a promising additive manufacturing technology, yet deeper understanding of the laser-material interaction is crucial to exploit the potential of the process. By simultaneous in-situ synchrotron x-ray and schlieren imaging, we probe directly the interconnected fluid dynamics of the vapour jet formed by the laser and the depression it produces in the melt pool. The combined imaging shows the formation of a stable plume over stable surface depressions, which becomes chaotic following transition to a full keyhole. We quantify process instability across several parameter sets by analysing keyhole and plume morphologies, and identify a previously unreported threshold of the energy input required for stable line scans. The effect of the powder layer and its impact on process stability is explored. These high-speed visualisations of the fluid mechanics governing LPBF enable us to identify unfavourable process dynamics associated with unwanted porosity, aiding the design of process windows at higher power and speed, and providing the potential for in-process monitoring of process stability.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In-Situ Observation of FCC→HCP Transformation-Induced Plasticity Behavior During Dynamic Deformation of CoCrNi Multi-principal Element Alloys

CoCrNi multi-principal element alloys (MPEAs) have potential as high toughness, blast resistant materials, but limited studies of their high strain rate behavior have been performed. Their high toughness has been attributed to low stacking fault energies and the activation of toughness enhancing deformation mechanisms, such as twinning- and transformation-induced plasticity (TWIP and TRIP, respectively), that may be affected by increased strain rate. This work examines a series of CoCrNi MPEAs tested with a miniaturized pressure bar, while simultaneous synchrotron x-ray diffraction and imaging are performed, and compares these results to those collected during quasi-static deformation at elevated temperatures. Here, the collected diffraction indicates that TRIP was active at elevated strain rates for the most Co-rich alloys containing 50 or 55 at. pct. Co, while TRIP behavior was suppressed at elevated strain rates in a 40 at. pct. Co alloy anticipated to experience TRIP. The suppression of TRIP in the lower Co alloy at high strain rates is attributed to adiabatic heating, consistent with suppression of TRIP as a result of elevated temperatures.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Strain rate effects on the mechanical behavior of porous titanium with different pore sizes

High strain-rate (up to 6600 s –1 ) and quasi-static compression tests are conducted on a powder-sintered porous titanium with different pore sizes (mean: 30 μm and 120 μm). In situ X-ray imaging is implemented to characterize the pores-scale deformation dynamics. The yield strength as a function of strain rate exhibits two stages of rate sensitivity, and the transition occurs at 1600 s –1 . X-ray images show that pore compaction and strain localizations occur preferentially at pores oriented perpendicular to the loading direction under quasi-static loading, but become more random under high strain-rate loading as a result of higher driving force and plastic deformation nucleation rate. Here, the more homogeneous nucleation of plastic deformation contributes to the increased rate sensitivity beyond 1600 s –1 . At the same strain rate, the yield strength of porous Ti as well as strain field homogeneity decreases significantly with increasing pore size. The small pore spacing in fine-pored Ti reduces the degree of stress concentrations around pores. Therefore, the higher stress concentrations in coarse-pored Ti lead to an earlier yield of matrix around pores and thus a lower bulk yield strength.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Impact-induced twinning in a magnesium alloy under different stress conditions

We investigate deformation twinning in a highly textured magnesium alloy plate of Mg-3.1%Al-0.9%Zn-0.4%Mn under edge-on impact with in situ, synchrotron-based, ultrafast X-ray diffraction measurements, and corresponding stress states are simulated with the finite element method. Deformation twinning and its anisotropy under the triaxial stress condition are explained by a statistical analysis of resolved shear stress. The critical resolved shear stress criterion is applicable under complicated stress conditions induced by high strain rate impact loading. Three typical simple stress conditions are further explored as verification and application cases: uniaxial-stress, uniaxial-strain, and plane-stress. Extension twinning in the magnesium alloy is prone to occur for impact loading applied perpendicular to the crystallographic c-axis, regardless of the exact stress conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Rate-dependent strength and deformation heterogeneity of B4C-reinforced Al composite: Time-resolved imaging with synchrotron X-rays

Dynamic (up to 5500 s -1 ) and quasi-static compression tests are conducted on a 15 wt% B4C particle-reinforced Al (B 4 C/Al) composite. In situ, high-speed synchrotron X-ray phase contrast imaging and digital image correlation are employed to map mesoscale deformation fields at μm and μs scales. The bulk stress–strain curves show significant strain and strain-rate hardening under dynamic compression. The strain-rate sensitivity exponent is an order of magnitude higher at high strain rates (> 10 3 s -1 ) than that at low strain rates (< 10 -2 s -1 ). Strain field mapping demonstrates distinct compressive strain localizations for both quasi-static and dynamic loading. Nevertheless, compressive strain localizations appear denser in spacing under dynamic loading, owing to spontaneous dislocation nucleation in both weak and strong zones. This results in a higher density of geometrically necessary dislocations, which contributes to the higher strain and strain-rate hardening of B 4 C/Al under dynamic loading. Additionally, the ratio of the maximum local strain to the bulk average is 1.5, and the local strain-rate enhancement cannot explain the increased rate sensitivity of B 4 C/Al under dynamic loading. Therefore, the rate-dependent deformation heterogeneity dominates the strain-rate hardening of B 4 C/Al. Postmortem analyses help correlate deformation features to particle- and grain-scale microstructures, yielding consistent results with mesoscale strain fields.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Direct observation on supersonic microprojectile penetration of carbon fiber composites with ultrafast synchrotron X-ray phase contrast imaging

High-speed penetration into carbon fiber composites is of fundamental importance to materials science and impact engineering, but research along this line suffers considerably from the lack of direct experimental observations. Here we investigate such penetration dynamics of a unidirectional carbon fiber reinforced epoxy (UCFRE) composite, with a combination of in situ, ultrafast, synchrotron phase contrast imaging and finite element (FE) analysis. The experiments yield the first direct observation on projectile trajectories and fiber-scale deformation and damage in the UCFRE composites during supersonic microprojectile penetration, for different fiber orientations (0 degrees - 90 degrees from the impact direction) and projectile velocities (600 - 850 m.s -1 ), at unprecedented temporal (~ 100 ps) and spatial (5 μm) resolutions. The maximum penetration depth decreases with increasing fiber orientation angles, as a result of anisotropic damage evolution in the composite sample. Strain localizations are prone to develop along a direction perpendicular to the fiber orientation, while the damage or cavity region, along the fiber direction. FE modeling with a three-dimensional Hashin criterion yields consistent projectile trajectory and cavity morphology with the experimental results. Finally, with increasing fiber orientation angles, damage analyses show a transition in the damage mode from fiber compression to matrix compression damage, in line with the increasing maximum penetration depth.

36 MATERIALS SCIENCE↗

NASA NTRS2019

A Diversity of Calcium-Rich Carbonates in EETA 79001

Carbonate minerals of martian origin are present in several martian meteorites in trace concentrations (less than 1 percent) and possess unique isotopic signatures that suggest that the martian environment and/or isotopic reservoirs are very different from the Earth’s. Carbonates are most common in the older martian meteorites (ALH 84001 and the nakhlites), however, there have been reports of carbonate in the younger shergottites including EETA 79001 (Mars meteorite Elephant Moraine 79001). Acidification studies of Zagami and Shergotty have shown that CO2 is released suggesting that carbonate phases are present in these meteorites, but the origin of these phases is controversial. The young ages of the shergottites makes them important samples for understanding the modern martian environment. The carbonates in EETA 79001 are the best-characterized secondary minerals in a shergottite, but their origin remains controversial. Gooding et al. argued that two types of carbonate occur with-in the glassy parts of the meteorite. One type, nearly pure CaCO3 associated with Ca-sulfate shows textural evidence for being present in the rock prior to it being shocked, suggesting formation on Mars. The second was more abundant and consists of Ca-rich carbonate, possibly with finely intergrown Mg-phosphate, but does not possess any textural relationships indicative of a martian origin. Carbon and oxygen isotopic studies of this carbonate yielded oxygen isotopes that potentially suggest a martian origin as well

Niles, P. B.↗

NASA NTRSDate not supplied

Triple Oxygen Isotope Kinetics of Sulfate From Pyrite Oxidation

Sulfates from low temperature terrestrial and marine environments are out of equilibrium with their oxygen sources. Instead, oxygen isotope compositions of sulfate imply they are dominated by kinetic signatures of oxidative and reductive processes (Killingsworth et al., 2022) that are under-constrained compared to equilibrium effects (Hayles and Killingsworth, 2022). Consequently, the specific role of pyrite oxidation in setting the oxygen isotope composition of sulfate is also under-constrained. This scenario inhibits a more nuanced understanding of small variations in the oxygen isotopes of sulfate and their implications for tracing oxygen sources and sulfur cycle transformations, particularly in low-temperature relatively sulfate-limited freshwater systems such as rivers, lakes, aquifers, and mining-affected environments. To alleviate these knowledge gaps, we conduct pyrite oxidation experiments at time scales spanning minutes to years, analyze the triple oxygen isotope compositions (∆ 17 O and δ 18 O) of sulfate products, and interpret results using molecular modeling. Our preliminary results show isotopic relationships of 1) pyrite-derived sulfate ∆ 17 O reaching above the meteoric water line as its δ 18 O becomes lighter than water, and 2) sulfate ∆ 17 O and δ 18 O extending between water and O 2 . From these results we interpret a kinetic isotope effect between sulfate and water and mixing between sulfate end members containing most of their oxygen atoms from water and from O 2 .

Oxygen isotopes↗