Search NASA⌕ Search

Engineering topics

Sun, T. F.

Publications and source records attributed to Sun, T. F..

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Recent advance progress of HL-3 experiments

Since the first plasma realized in 2020, a series of key systems on HL-3 (known as HL-2M before) tokamak have been equipped/upgraded, including in-vessel components (the first wall, lower divertor, and toroidal cryogenic/water-cooling/baking/glow discharge systems, etc.), auxiliary heating system of 11 MW, and 28 diagnostic systems (to measure the plasma density, electron temperature, radiation, magnetic field, etc.). Magnet field systems were commissioned firstly for divertor plasma discharges. During the 2nd experimental campaign of HL-3 tokamak, several great progresses have been achieved. Firstly, the successful operation with plasma current larger than 1 MA was achieved under a divertor configuration. Secondly, the advanced divertor concept with two distinct snowflake configurations was realized. It is found that the distribution of ion saturation current and heat flux on bottom plate becomes wide due to magnetic surface expansion, demonstrating the advantage of such configuration in the heat flux mitigation. In addition, using the combination of NBI, ECRH and LHCD, the standard sawtoothing high confinement mode of megampere plasma was firstly accessed on the HL-3. The successful commissioning of HL-3 is beneficial for the initial operation of ITER.

1 MA plasma↗
DOE OSTI2023

Toroidal modeling of plasma flow damping and density pump-out by RMP during ELM mitigation in HL-2A

Reduction of both the plasma density and toroidal flow speed, due to application of the predominantly n = 1 (n is the toroidal mode number) resonant magnetic perturbation (RMP) for controlling the edge localized mode in the HL-2A tokamak, is numerically investigated utilizing the quasi-linear initial-value code MARS-Q (Liu et al 2013 Phys. Plasmas 20 042503). Simulation results reveal that the neoclassical toroidal viscosity (NTV) due to three dimensional fields plays the key role in modifying the plasma momentum and particle transport in the HL-2A discharge. By comparing the modeling results with the measured density pump-out in the experiment, the electron NTV particle flux model, in combination with the free-boundary condition for the axisymmetric change of the density at the plasma edge, is found to yield the best agreement in terms of both the pump-out level and the overall time scale. Further sensitivity studies show that the simulated density pump-out level is reasonably robust against variations in the model assumptions, including the particle diffusion model and the non-ambipolar versus ambipolar NTV particle flux. The latter however affects the time scale for reaching the steady state solution. Finally, it is found that the plasma edge-peeling response, the NTV torque, as well as the plasma momentum and particle transport, all are sensitive to the toroidal phase difference between the upper and lower rows of the RMP coil currents in HL-2A, with the 30 ∘ coil phasing producing the minimal side effects on the plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Toroidal modeling of 3D perturbations generated by current filaments in scrape-off layer in tokamak with biased divertor targets

The divertor biasing technique offers a promising alternative to control the edge localized mode (ELM) as well as the divertor heat load in tokamaks, as compared to the resonant magnetic perturbation (RMP) generated by magnetic coils. The linear resistive MHD code MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) is employed to study the plasma response to the n = 2 (n is the toroidal mode number) field perturbation in HL-2A, produced by the divertor biasing current filaments flowing in the scrape-off layer region. The response field due to biasing currents is compared with the RMP field utilized for ELM control in HL-2A. The strength of the radial resonant field perturbation, produced by the biasing currents of 100 A level, is found to be comparable with RMP generated by several kA of ELM control coil currents for the reference plasma. The plasma normal displacement near the X-point and the associated neoclassical toroidal viscosity torque are also computed to be similar between these two techniques. The modeling results thus strongly suggest that the biasing technique can be applied to control ELMs. Moreover, the biasing currents produce field perturbations, including the plasma response, that are localized more near the plasma edge (compared to the RMP counterpart), thus reducing the chance of mode locking associated with core perturbations. Particle orbit tracing also reveals that the biasing current produced magnetic perturbation tends to widen the heat deposition region and induce the strike point splitting of the ion saturation flow on the outer divertor surface, consistent with experimental observations in HL-2A. These toroidal modeling results confirm the possibility of ELM control and plasma exhaust solution by the divertor biasing technique.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗