Engineering topics

Sutton, Austin T.

Publications and source records attributed to Sutton, Austin T..

5 records

DOE OSTI2024

Spot pattern welding scanning strategy for sensor embedding and residual stress reduction in laser-foil-printing additive manufacturing

Here, this paper aims to present spot pattern welding (SPW) as a scanning strategy for laser-foil-printing (LFP) additive manufacturing (AM) in place of the previously used continuous pattern welding (CPW) (line-raster scanning). The SPW strategy involves generating a sequence of overlapping spot welds on the metal foil, allowing the laser to form dense and uniform weld beads. This in turn reduces thermal gradients, promotes material consolidation and helps mitigate process-related risks such as thermal cracking, porosity, keyholing and Marangoni effects. 304L stainless steel (SS) feedstock is used to fabricate test specimens using the LFP system. Imaging techniques are used to examine the melt pool dimensions and layer bonding. In addition, the parts are evaluated for residual stresses, mechanical strength and grain size. Compared to CPW, SPW provides a more reliable heating/cooling relationship that is less dependent on part geometry. The overlapping spot welds distribute heat more evenly, minimizing the risk of elevated temperatures during the AM process. In addition, the resulting dense and uniform weld beads contribute to lower residual stresses in the printed part. To the best of the authors’ knowledge, this is the first study to thoroughly investigate SPW as a scanning strategy using the LFP process. In general, SPW presents a promising strategy for securing embedded sensors into LFP parts while minimizing residual stresses.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Modeling powder spreadability in powder-based processes using the discrete element method

Powder-bed fusion (PBF) processes refer to a subset of Additive Manufacturing (AM) techniques where powder is spread on the build-plate before melting (by a laser or electron beam). While PBF processes are attractive due to their ability for realizing complex structures that are either difficult or impossible to create through conventional means, the parts fabricated with these techniques can exhibit defects such as pores, inclusions, and excessive surface roughness. To minimize these defects, much research has been dedicated towards process maturation by optimizing laser or electron beam parameters. However, these developmental efforts typically do not address the recoating process where achieving dense and uniform layers of powder is a necessity for ensuring process repeatability and part quality. While the recoating process can be studied through experimentation, the dynamics of particle movement are difficult to analyze experimentally. Therefore, here, in this study, powder spreading in PBF was simulated through the Discrete Element Method (DEM) to elucidate the mechanisms that control powder-bed quality. Utilizing the Buckingham Pi theorem, a dimensionless metric referred to as the spreading index is developed that combines powder-bed density, roughness, and particle size to assess the quality of powder layers. The formulated spreading index is then related to several dimensionless quantities that provide insight into the mechanisms dominating powder spreading in PBF. The DEM simulations conducted in this work focused on the scenario where powder is spread onto an existing powder bed and revealed that a reduction in the recoating velocity causes an increase in the spreading index while little to no impact on the spreading index was observed when varying layer thickness from 30 μm to 75 μm.Particle size effects on the powder-bed quality were also investigated.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Experimental approach for development of a powder spreading metric in additive manufacturing

The powder spreading is a vital step of powder-based additive manufacturing (AM) processes. The quality of spread powder can considerably influence the properties of fabricated parts. Poorly packed powder beds with high surface roughness result in printed part layers with large porosity and low dimensional accuracy, leading to poor mechanical properties. Therefore, the powder spreadability and its dependence on process parameters and powder characteristics should be quantified to improve the efficiency of powder-based AM methods. This study proposes a novel dimensionless powder spreadability metric that can be commonly used in different powder-based AM processes. The quality of spread powder in terms of powder bed density and surface roughness was evaluated by adjusting the process parameters including recoating velocity and layer thickness, and powder characteristics including particle size distribution. In addition, the dynamic repose angle was proposed and examined as another powder spreadability metric. Furthermore, the results showed that these two proposed metrics were strongly correlated and lower recoating velocity and larger layer thickness led to higher spreadability and lower dynamic repose angle.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Investigation of Mechanical Properties of Parts Fabricated with Gas- and Water-Atomized 304L Stainless Steel Powder in the Laser Powder Bed Fusion Process

In this report the use of gas-atomized powder as the feedstock material for the Laser Powder Bed Fusion (L-PBF) process is common in the Additive Manufacturing (AM) community. Although gas-atomization produces powder with high sphericity, its relatively expensive production cost is a downside for application in AM processes. Water atomization of powder may overcome this limitation due to its low cost relative to the gas-atomization process. In this work, gas- and water-atomized 304L stainless steel powders were morphologically characterized through Scanning Electron Microscopy (SEM). The water-atomized powder had a wider particle size distribution and exhibited less sphericity. Measuring powder flowability using the Revolution Powder Analyzer (RPA) indicated that the water-atomized powder had less flowablility than the gas-atomized powder. Through examining the mechanical properties of L-PBF fabricated parts using tensile tests, the gas-atomized powder had significantly higher yield tensile strength and elongation than the water-atomized powder, however, their ultimate tensile strengths were not significantly different.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Evolution of AISI 304L stainless steel part properties due to powder recycling in laser powder-bed fusion

Selective laser melting (SLM) is a powder-bed fusion process in Additive Manufacturing (AM) that uses a laser beam to selectively fuse layers of powder into near net-shape components with little porosity. However, inconsistencies in the part properties due to the presence of defects in as-built components has hindered the widespread adoption of SLM for industrial applications forcing researchers to study the sources of variation for quality control purposes. A critical area suspected of creating variation in the part properties is the feedstock, where batch-to-batch differences as well as changes in the powder properties with reuse have the potential to affect performance. During processing, laser spatter and condensate eject from the melt pool and deposit into the powder-bed surrounding the parts. These particulates, more commonly known as ejecta, differ morphologically and chemically from the virgin powder compromising its reusability. In this study, 304L stainless steel powder was recycled for a total of 5 times through a systematic approach aimed at accelerating powder degradation to reveal the influence on both the tensile and impact toughness properties. Through analysis of variance (ANOVA), it was found that tensile properties did not change with reuse, while the impact toughness showed a steady decline illustrating the differences in static and dynamic part properties due to powder recycling.

36 MATERIALS SCIENCE↗