Engineering topics
Publications and source records attributed to Swedlow, J. L..
Priorities for research in advanced laminated fibrous composite materials are presented. Supporting evidence is presented in two bodies, including a general literature survey and a survey of aerospace composite hardware and service experience. Both surveys were undertaken during 1977-1979. Specific results and conclusions indicate that a significant portion of contemporary published research diverges from recommended priorites.
Three cracked geometries are studied with the aid of a new finite element model. The procedure employs a variable singularity at the crack tip that tracks changes in the material response during the loading process. Two of the problems are tension-loaded center-crack panels and the other is a three-point bend specimen. Results usually agree with other numerical and analytical analyses, except the finding that J is path dependent as a substantial plastic zone develops. Credible J values are obtained near the crack tip and J shows a significant increase as the radius of J path increases over two orders of magnitude. Incremental and deformation theories are identical provided the stresses exhibit proportionality found in the far field stresses but not near the tip.
Using a new special element for elasto-plastic flow, a nearly square, center-cracked plate of simulated A533 steel is analyzed. Selected results are examined locally to the crack's tip. It is found that a sharp transition in the distribution of deformation and stress occurs after the initial elastic response, and that this state is followed by fairly stable behavior over a considerable portion of the load range. Distribution of strain energy density is noted, and implications for use of the parameter J and for additional work are discussed briefly.
Computer-oriented finite-element techniques for extracting the required information about the influence of cracks on stress fields are reviewed based on the knowledge that cracks induce stress singularities. Attention is focused on modeling behavior at a crack tip. Also discussed are crack tip analysis, utility of crack tip finite elements, and newer developments for cases where the singularity is not known a priori, i.e. the strength of the singularity is not established in advance of the computation. Available results are briefly summarized.
Direct descriptions of the structure of a singularity would describe the radial and angular distributions of the field quantities as explicitly as practicable along with some measure of the intensity of the singularity. This paper discusses such an approach based on recent development of numerical methods for elastoplastic flow. Attention is restricted to problems where one variable or set of variables is finite at the origin of the singularity but a second set is not.
An approach is described for singularity computations based on a numerical method for elastoplastic flow to delineate radial and angular distribution of field quantities and measure the intensity of the singularity. The method is applicable to problems in solid mechanics and lends itself to certain types of heat flow and fluid motion studies. Its use is not limited to linear, elastic, small strain, or two-dimensional situations.
The influence of crack closure and elastoplastic flow on the bending behavior of thin cracked plates is investigated using an incremental elastoplastic plate bending finite element computer program. The finite element program was developed using assumptions consistent with Kirchhoff fourth-order plate theory while the material property treatment permits general isotropic work hardening with local elastic unloading. This technique is applied to the problem of a large centrally through cracked plate subject to remote circular bending. Comparison is drawn between two cases of the bending problem. The first neglects the possibility of crack face interference with bending, and the second includes a kinematic prohibition against the crack face from passing through the symmetry plane. Results are reported which isolate the effects of elastoplastic flow and crack closure.
Theory is stated in terms of increments of displacement and stress, and of instantaneous or accumulated values of stress. The equilibrium equations, in the absence of body forces, are written, along with constitutive relations for plane strain.
It is demonstrated that the problem of elasto-plastic finite deformation is governed by a quasi-linear model irrespective of deformation magnitude. This feature follows from the adoption of a rate viewpoint toward finite deformation analysis in an Eulerian reference frame. Objectivity of the formulation is preserved by introduction of a frame-invariant stress rate. Equations for piece-wise linear incremental finite element analysis are developed by application of the Galerkin method to the instantaneously linear governing differential equations of the quasi-linear model. Numerical solution capability has been established for problems of plane strain and plane stress. The accuracy of the numerical analysis is demonstrated by consideration of a number of problems of homogeneous finite deformation admitting comparative analytic solution. It is shown that accurate, objective numerical solutions can be obtained for problems involving dimensional changes of an order of magnitude and rotations of a full radian.
The theory of elasto-plastic flow is developed so that it may accommodate features such as work-hardening, anisotropy, plastic compressibility, non-continuous loading including local or global unloading, and others. A complete theory is given in quasi-linear form; as a result, many useful attributes are accessible. Several integral theorems may be written, finite deformations may be incorporated, and efficient methods for solving problems may be developed; these and other aspects are described in some detail. The theory is reduced to special forms for 2-space, and extensive experience in solving such problems is cited.
A method is presented for estimating the stress intensity factor characteristic of crack extension in a specially orthotropic advanced fiber composite laminate, based on the elastic properties and ultimate principal strengths of a lamina, the laminate construction, and the experimentally determined value of the characteristic stress intensity factor of an arbitrary angle-plied, midplane symmetric laminate. A comparison of the results obtained from this method with limited experimental data for graphite/epoxy laminates indicates that the method is quite accurate for this particular material system. The predictive method is also used, in conjunction with experimental data, to estimate the size of a damage zone surrounding the crack tip.
The extension of linear elastic fracture mechanics (LEFM) from metallic alloys to advanced fiber composite laminates is considered. LEFM is shown to be valid for both isotropic and anisotropic homogeneous continua; the applicability of LEFM to advanced fiber composites is thus dependent on the validity of a homogeneous model of such materials. An experimental program to determine the validity of such a model for graphite/epoxy laminates is reviewed. Such laminates are found to have an apparent fracture toughness, from which it is inferred that a homogeneous material model is valid for the particular specimen geometry and composite laminates considered. Strain energy release rates are calculated from the experimentally determined fracture toughness of the various laminates. These strain energy release rates are found to lie in one of two groups, depending upon whether crack extension required fiber failure or matrix failure. The latter case is further investigated. It is concluded that matrix failure is governed by the tensile stress normal to the crack path.
Pilot tests were run to determine the applicability of the concepts of linear elastic fracture mechanics (LEFM) to the description of the mechanical behavior of initially cracked specimens of advanced fiber composite laminates. It was found that the failure mechanisms in such specimens were largely crack-dominated and that LEFM procedures were applicable even when the apparent failure mechanism was not explicitly dominated by a starter crack.
Consideration of the effect of crack front curvature (CFC) on the K calibration of five special geometries in which CFC occurs. The five cases considered include an elliptical crack in an infinite medium, an internal annular crack in a thick-walled cylinder, a through crack in a flat plate, a part-through crack in a plate, and an irregularly shaped crack in a solid. It is shown that K depends on CFC differently in each case.
During the past year an experimental program in the fracture of advanced fiber composites has been completed. The experimental program has given direction to additional experimental and theoretical work. A synthesis program for designing low weight multifastener joints in composites is proposed, based on extensive analytical background. A number of failed joints have been thoroughly analyzed to evaluate the failure hypothesis used in the synthesis procedure. Finally, a new solution is reported for isotropic and anisotropic laminates using the boundary-integral method. The solution method offers significant savings of computer core and time for important problems.
A general theory of elastoplastic flow is formulated for work-hardening materials that may be both anisotropic and compressible. Because the theory is quasi-linear, it may be cast in terms of integral equations and the result is an extended form of Somigliana's identity. When these relations are evaluated on the boundary of a solid, their dimensionality is reduced. Previous experience with simpler materials shows that arbitrary problems may be solved in a direct manner.
Edge cracked metal sheet elastoplastic strain distribution determination, using optical interference, moire technique and plane stress model finite element method
Crack opening displacement concept in fracture mechanics, considering crack tip radius as measure of extension potential