Engineering topics

Szodruch, J.

Publications and source records attributed to Szodruch, J..

7 records

NASA NTRS1986

Wind tunnel technology for the development of future commercial aircraft

Requirements for new technologies in the area of civil aircraft design are mainly related to the high cost involved in the purchase of modern, fuel saving aircraft. A second important factor is the long term rise in the price of fuel. The demonstration of the benefits of new technologies, as far as these are related to aerodynamics, will,for the foreseeable future, still be based on wind tunnel measurements. Theoretical computation methods are very successfully used in design work, wing optimization, and an estimation of the Reynolds number effect. However, wind tunnel tests are still needed to verify the feasibility of the considered concepts. Along with other costs, the cost for the wind tunnel tests needed for the development of an aircraft is steadily increasing. The present investigation is concerned with the effect of numerical aerodynamics and civil aircraft technology on the development of wind tunnels. Attention is given to the requirements for the wind tunnel, investigative methods, measurement technology, models, and the relation between wind tunnel experiments and theoretical methods.

Szodruch, J.↗

NASA NTRS1982

Measurement and visualization of skin friction on the leeside of delta wings in supersonic flow

The reported investigation was conducted with the aid of the NASA Ames High Reynolds Number Wind Tunnel. The flow conditions considered involved free stream Mach numbers of 2 and 3, and a Reynolds number of approximately 10,000,000 p. m. The employed model was a delta wing with an angle of 70 deg. A method reported by Tanner (1977) was used for the measurement of the skin friction. This method involves the use of a laser interferometer to determine the change in the thickness of an oil film. The procedure can also be employed for a visualization of skin friction in the form of interferograms. The investigation shows that skin friction measurements can provide a significant contribution to a physical understanding of the flow processes at the delta wing.

Szodruch, J.↗

NASA NTRS1981

Application of a Laser Interferometer Skin-Friction Meter in Complex Flows

A nonintrusive skin-friction meter has been found useful for a variety of complex wind-tunnel flows. This meter measures skin friction with a remotely located laser interferometer that monitors the thickness change of a thin oil film. Its accuracy has been proven in a low-speed flat-plate flow. The wind-tunnel flows described here include sub-sonic separated and reattached flow over a rearward-facing step, supersonic flow over a flat plate at high Reynolds numbers, and supersonic three - dimensional vortical flow over the lee of a delta wing at angle of attack. The data-reduction analysis was extended to apply to three-dimensional flows with unknown flow direction, large pressure and shear gradients, and large oil viscosity changes with time. The skin friction measurements were verified, where possible, with results from more conventional techniques and also from theoretical computations.

Monson, D. J.↗

NASA NTRS1981

Application of a laser interferometer skin-friction meter in complex flows

The application of a nonintrusive laser-interferometer skin-friction meter, which measures skin friction with a remotely located laser interferometer that monitors the thickness change of a thin oil film, is extended both experimentally and theoretically to several complex wind-tunnel flows. These include two-dimensional seperated and reattached subsonic flows with large pressure and shear gradients, and two and three-dimensional supersonic flows at high Reynolds number, which include variable wall temperatures and cross-flows. In addition, it is found that the instrument can provide an accurate location of the mean reattachment length for separated flows. Results show that levels up to 120 N/sq m, or 40 times higher than previous tests, can be obtained, despite encountering some limits to the method for very high skin-friction levels. It is concluded that these results establish the utility of this instrument for measuring skin friction in a wide variety of flows of interest in aerodynamic testing.

Monson, D. J.↗

NASA NTRS1980

Experimental study of supersonic viscous leeside flow over a slender delta wing

An investigation was conducted to study in detail the vortical flow over the leeward side of a 70 deg swept delta wing having subsonic and supersonic leading edges. Two types of flow were encountered and studied, namely leading edge separation and separation with a shock. Especially for the latter type, Reynolds number plays an important role and unexpected strong streamwise vortices were observed. An optical method is described to obtain a first aproximation of shear stress values in the streamwise direction across the wing span.

Szodruch, J.↗

NASA NTRS1980

Types of leeside flow over delta wings

It is noted that so far most systematic investigations on the lee side flow over delta wings at supersonic speeds are concerned with flat upper surfaces. On the basis of these results, the paper makes an attempt to characterize the different types of flow over a wing with a delta-shaped upper surface by varying a number of parameters. It is concluded that the work should be considered a first step toward systematizing the flow over delta-shaped lee sides as well.

Szodruch, J.↗

NASA NTRS1978

Reynolds number influence on leeside flowfields

Experimental results on the Reynolds number influence on the leeside flowfield of planar delta wings at supersonic speeds are presented. Wind tunnel experiments on two delta wing models with straight and sharp leading edges at freestream Mach number of 2.5 and 3.5 and angle of attack between 1 deg and 12.5 deg were carried out. The cross-sectional shape was triangular and the relative height was 0.25. The flow types investigated were to the left and right of the Stanbrook-Squire boundary. Under leading-edge separation conditions, the vortex position and intensity, and thus the suction pressure, vary with Re while the flow type remains nearly unchanged. In the region of separation with embedded shock, Re affects not only the shape of the separation bubble and pressure level near the leading edge but also the type of flow. At sufficiently high Re the flow type of separation with shock changes to one with shock-induced separation.

Szodruch, J.↗