Engineering topics

Tabakoff, W.

Publications and source records attributed to Tabakoff, W..

At least 19 records

NASA NTRS1986

Three-dimensional flow field measurements in a radial inflow turbine scroll using LDV

The results of an experimental study of the three-dimensional flow field in a radial inflow turbine scroll are presented. A two-color LDV system was used in the measurement of three orthogonal velocity components at 758 points located throughout the scroll and the unvaned portion of the nozzle. The cold flow experimental results are presented for through-flow velocity contours and the cross velocity vectors.

Malak, M. F.↗

NASA NTRS1984

The three-dimensional compressible flow in a radial inflow turbine scroll

This work presents the results of an analytical study and an experimental investigation of the three-dimensional flow in a turbine scroll. The finite element method is used in the iterative numerical solution of the locally linearized governing equations for the three-dimensional velocity potential field. The results of the numerical computations are compared with the experimental measurements in the scroll cross sections, which were obtained using laser Doppler velocimetry and hot wire techniques. The results of the computations show a variation in the flow conditions around the rotor periphery which was found to depend on the scroll geometry.

Hamed, A.↗

NASA NTRS1983

Effect of particle presence on the incompressible inviscid flow through a two dimensional compressor cascade

A computational model is developed for calculating the flow field, in the presence of solid particles, through a two-dimensional compressor cascade. Results show that the effect of solid particles on the flow field contributes to the bending of the streamlines toward the blade suction surface. It is determined that the difference in the pressure coefficient for particulate flow, with 165 micron diameter for the particles, is of the order of 3 percent over the air only flow. The change in the pressure coefficients is shown to be much larger for very small particles. It was found that the total pressure loss associated with the particulate flow is very high for very small particles as compared with large particles. The total pressure loss is also shown to be higher for accelerating flow than for decelerating flow. The total pressure loss is shown to be directly proportional to the particle concentration. It is concluded that significant reductions in performance can occur in a real multistage machine due to the changes in the pressure ratios, particularly if the suspended matter is small particles.

Balan, C.↗

NASA NTRS1983

Three-dimensional flow measurements in a turbine scroll

A study was conducted to determine experimentally the flow behavior in combined scroll nozzle assembly of a radial inflow turbine. Hot film anemometry technique was used to measure the three-dimensional flow velocity in the scroll. The through-flow and secondary flow velocity components are measured at various points in three scroll sections.

Tabakoff, W.↗

NASA NTRS1983

A study of the surface deterioration due to erosion

It is pointed out that materials exposed to particle impacts are eroded and subjected to deterioration of their surface quality. In the case of turbomachinery, this surface deterioration can lead to a significant decrease in engine performance. Tabakoff and Balan (1981) have conducted experiments on the erosion related performance changes in two-dimensional airfoil cascades. It was found that the increase in surface roughness associated with erosion is a major factor in the performance decrease of the cascades. Attention is given to experiments which were conducted on 6061 T6 flat plate aluminum specimens. A series of experiments were carried out in an erosion wind tunnel using a collimated beam of particles. In agreement with existing theories and experiments, erosion ripple generation was observed for the angles of attack up to 60 degrees.

Tabakoff, W.↗

NASA NTRS1983

A method of predicting the performance deterioration of a compressor cascade due to sand erosion

Performance deterioration due to sand erosion is a well known phenomena for aircraft engines operating in particulate flow environments. A method for predicting this performance deterioration is developed and applied to a two dimensional compressor cascade. The locations of the particles impacts are computed by analyzing the trajectories of the individual particles. From this analysis, the material removed, the changes in the airfoil shape, and the roughness development over the surface are estimated as a function of time. The resulting airfoil profiles are analyzed for predicting performance by using an inviscid-viscous interaction technique. The analytical solution is compared with experimental results.

Balan, C.↗

NASA NTRS1983

Effect of particle presence on the incompressible inviscid flow through a two dimensional compressor cascade

A computational model for calculating the flow field, in the presence of solid particles, through a two dimensional compressor cascade is presented. The method treats the particle phase in the Lagrangian system and the fluid phase in the Eulerian system. The equations of momentum of the fluid phase are modified to account for the momentum exchange between the two phases. The resulting modified momentum and continuity equations are reduced to the conventional stream function-vorticity formulation. The analysis yields the change in the blade surface pressure distribution, the total pressure and velocity in the flow field. Based on this, it is possible to predict the decrease in compressor performance under the presence of particles.

Balan, C.↗

NASA NTRS1982

Compressor cascade performance deterioration caused by sand ingestion

Airfoil cascade erosion and performance deterioration was investigated in a gas particle cascade tunnel. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand. The results of the experimental measurements are presented to show the change in the blade surface erosion, pressure distribution and the total loss coefficient with erosion. The surface quality of the blades exposed to particulate flows are changing the material surfaces. With time, the surface roughness increases and leads to a decrease in engine performance. It was found that the surface roughness values increase asymptotically to a maximum value with increased erosion. The experimental results indicate that the roughness parameters correlate well against the mass of particles impacting unit area of the surface. Such a correlation is useful in aerodynamics and performance computations in turbomachinery.

Tabakoff, W.↗

NASA NTRS1982

Environmental solid particle effects on compressor cascade performance

The effect of suspended solid particles on the performance of the compressor cascade was investigated experimentally in a specially built cascade tunnel, using quartz sand particles. The cascades were made of NACA 65(10)10 airfoils. Three cascades were tested, one accelerating cascade and two diffusing cascades. The theoretical analysis assumes inviscid and incompressible two dimensional flow. The momentum exchange between the fluid and the particle is accounted for by the interphase force terms in the fluid momentum equation. The modified fluid phase momentum equations and the continuity equation are reduced to the conventional stream function vorticity formulation. The method treats the fluid phase in the Eulerian system and the particle phase in Lagrangian system. The experimental results indicate a small increase in the blade surface static pressures, while the theoretical results indicate a small decrease. The theoretical analysis, also predicts the loss in total pressure associated with the particulate flow through the cascade.

Tabakoff, W.↗

NASA NTRS1982

Three-dimensional flow measurements in a vaneless radial turbine scroll

The flow behavior in a vaneless radial turbine scroll was examined experimentally. The data was obtained using the slant sensor technique of hot film anemometry. This method used the unsymmetric heat transfer characteristics of a constant temperature hot film sensor to detect the flow direction and magnitude. This was achieved by obtaining a velocity vector measurement at three sensor positions with respect to the flow. The true magnitude and direction of the velocity vector was then found using these values and a Newton-Raphson numerical technique. The through flow and secondary flow velocity components are measured at various points in three scroll sections.

Tabakoff, W.↗

NASA NTRS1982

Three dimensional flow measurements in a turbine scroll

A study was conducted to determine experimentally the flow behavior in combined scroll nozzle assembly of a radial inflow turbine. Hot film anemometry technique was used to measure the three dimensional flow velocity in the scroll. The through flow and secondary flow velocity components are measured at various points in three scroll sections.

Tabakoff, W.↗

NASA NTRS1982

A study of viscous flow in stator and rotor passages

A numerical technique to predict the viscous behavior in the three-dimensional domain of rotating and stationary blade passages is presented. The analysis is based upon the numerical integration of the incompressible Navier-Stokes equations. An approach is taken to combine the three momentum equations and the continuity equation into two sets of vorticity transport-stream function equations. These equations are expressed along families of arbitrarily defined orthogonally intersecting surfaces placed within the blade passage. Unlike the stream surfaces, the arbitrary surfaces allow fluid to flow across. The numerical code employs a nonorthogonal body fitted coordinate system on each of the intersecting surfaces. The solution process involves the iterative combination of the solutions on the two families of intersecting surfaces for a complete solution. The results of flow in thin blade stationary and rotating polar ducts is presented.

Sheoran, Y.↗

NASA NTRS1981

A study of the viscous and nonadiabatic flow in radial turbines

A method for analyzing the viscous nonadiabatic flow within turbomachine rotors is presented. The field analysis is based upon the numerical integration of the incompressible Navier-Stokes equations together with the energy equation over the rotors blade-to-blade stream channels. The numerical code used to solve the governing equations employs a nonorthogonal boundary fitted coordinate system that suits the most complicated blade geometries. Effects of turbulence are modeled with two equations; one expressing the development of the turbulence kinetic energy and the other its dissipation rate. The method of analysis is applied to a radial inflow turbine. The solution obtained indicates the severity of the complex interaction mechanism that occurs between different flow regimes (i.e., boundary layers, recirculating eddies, separation zones, etc.). Comparison with nonviscous flow solutions tend to justify strongly the inadequacy of using the latter with standard boundary layer techniques to obtain viscous flow details within turbomachine rotors. Capabilities and limitations of the present method of analysis are discussed.

Khalil, I.↗

NASA NTRS1981

Effects of solid particles suspended in fluid flow through an axial flow compressor stage

An approximate method for calculating the flow properties of gas-particle mixture flowing over blades in a cascade is studied. Using an analytical method, the solid particle trajectory and location of collisions between the solid particles and the blade surfaces are determined. In addition an experimental investigation of the trajectories and velocities of solid particles suspended in a fluid passing through an axial flow compressor cascade was performed. The cascade blades were made of 2024 aluminum alloy and the solid particles used were quartz sand with average diameter of 165 microns. The following parameters were investigated: blade pressure distribution, and total pressure loss coefficient, both depending on the degree of erosion. In addition, a theoretical estimation of the blade erosion is compared with the experimental data.

Tabakoff, W.↗

NASA NTRS1980

A calculation procedure for viscous flow in turbomachines, volume 3

A method for analyzing the nonadiabatic viscous flow through turbomachine blade passages was developed. The field analysis is based upon the numerical integration of the full incompressible Navier-Stokes equations, together with the energy equation on the blade-to-blade surface. A FORTRAN IV computer program was written based on this method. The numerical code used to solve the governing equations employs a nonorthogonal boundary fitted coordinate system. The flow may be axial, radial or mixed and there may be a change in stream channel thickness in the through-flow direction. The inputs required for two FORTRAN IV programs are presented. The first program considers laminar flows and the second can handle turbulent flows. Numerical examples are included to illustrate the use of the program, and to show the results that are obtained.

Khalil, I.↗

NASA NTRS1980

A calculation procedure for viscous flow in turbomachines, volume 2

Turbulent flow within turbomachines having arbitrary blade geometries is examined. Effects of turbulence are modeled using two equations, one expressing the development of the turbulence kinetic energy and the other its dissipation rate. To account for complicated blade geometries, the flow equations are formulated in terms of a nonorthogonal boundary fitted coordinate system. The analysis is applied to a radial inflow turbine. The solution obtained indicates the severity of the complex interaction mechanism that occurs between the different flow regimes (i.e., boundary layers, recirculating eddies, separation zones, etc.). Comparison with nonviscous flow solutions tend to justify strongly the inadequacy of using the latter with standard boundary layer techniques to obtain viscous flow details within turbomachine rotors. Capabilities and limitations of the present method of analysis are discussed.

Khalil, J.↗

NASA NTRS1979

Flow in nonrotating passages of radial inflow turbines

The analysis of irrotational incompressible flow field in the stator unit of a radial inflow turbine is presented. The solution in the combined scroll-nozzle assembly is complicated by the domain geometry and by its multiconnectivity. This model is necessary, however, in order to provide a better understanding of the mutual interaction effects of these two components on the flow field. The finite element method is used in the solution which is limited to the two dimensional case. A substructuring technique is adopted in the computational procedure and results in considerable savings in both computer time and core storage requirements. The results are presented for the flow velocity magnitude and direction in the scroll and through the various nozzles, for two nozzle blade geometries. In addition, the mass flow rates in the different nozzles are computed and their deviations from the mean value determined.

Baskharone, E.↗

NASA NTRS1979

A calculation procedure for viscous flow in turbomachines, volume 1

A method for analyzing the nonadiabatic viscous flow through turbomachine rotors is presented. The field analysis is based upon the numerical integration of the full incompressible stream function vorticity form of the Navier-Stokes equations, together with the energy equation, over the rotor blade-to-blade stream channels. The numerical code used to solve the governing equations employs a nonorthogonal boundary fitted coordinate system that suits the most complicated blade geometries. A numerical scheme is used to carry out the necessary integration of the elliptic governing equations. The flow characteristics within the rotor of a radial inflow turbine are investigated over a wide range of operating conditions. The calculated results are compared to existing experimental data. The flow in a radial compressor is analyzed in order to study the behavior of viscous flow in diffusing cascades. The results are compared qualitatively to known experimental trends. The solution obtained provides insight into the flow phenomena in this type of turbomachine. It is concluded that the method of analysis is quite general and gives a good representation of the actual flow behavior within turbomachine passages.

Khalil, I.↗