Search NASA⌕ Search

Engineering topics

Tacina, K. M.

Publications and source records attributed to Tacina, K. M..

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Microstructural and Mechanical Characterization of a Dispersion Strengthened Medium Entropy Alloy Produced Using Selective Laser Melting

High entropy alloys (HEAs) are an interesting new class of alloys which have been shown to exhibit both notable strength and ductility for a wide range of temperature and stresses. In addition, the remarkably small difference between the solvus and liquidus temperatures for many face centered cubic HEAs makes them an excellent candidate for selective laser melting fabrication. In this study, the microstructure and mechanical properties of a dispersion strengthened equiatomic NiCoCr alloy successfully produced using selective laser melting are explored. The effect laser speed, laser power, and powder recyclability have on final part density and microstructural segregation are analyzed through both x-ray diffraction and high resolution scanning electron microscopy. These results are further validated and compared to stable phase predictions produced using a commercially available high entropy alloy mobility database. Lastly, the tensile strengths resulting from different heat treatment pathways are detailed.

Smith, T. M.↗
NASA NTRS2019

A Third-Generation Swirl-Venturi Lean Direct Injection Combustor with a Prefilming Pilot Injector

This paper presents experimental results for a low-NOxaero gas turbine combustor, in particular, a third-generationswirl-venturi lean direct injection (SV-LDI-3) combustor conceptcalled V4. The purpose of testing was three-fold. First,to evaluate the combustor against the 80% NOx reduction goalset by NASA’s AATT project. Second, to compare V4 to a previousSV-LDI-3 combustor concept called V3, especially at lowpower conditions. Third, to examine the accuracy of a type ofcorrelation equation frequently used by engine systems analysisgroups to estimate NOx emissions. All three testing goals weremet. For the first testing goal, with an estimated NOx reductionof 85%-90%, SV-LDI-3 V4 surpassed the AATT goal. For thesecond goal, however, V4 did not perform better than V3 at lowpower conditions. For the third goal, it was found that a majorassumption of the correlation equations — a simple dependenceon combustor inlet pressure — did not hold.

Tacina, K. M.↗
NASA NTRS2017

A Comparison of Combustion Dynamics for Multiple 7-Point Lean Direct Injection Combustor Configurations

The combustion dynamics of multiple 7-point lean direct injection (LDI) combustor configurations are compared. LDI is a fuel-lean combustor concept for aero gas turbine engines in which multiple small fuel-air mixers replace one traditionally-sized fuel-air mixer. This 7-point LDI configuration has a circular cross section, with a center (pilot) fuel-air mixer surrounded by six outer (main) fuel-air mixers. Each fuel-air mixer consists of an axial air swirler followed by a converging-diverging venturi. A simplex fuel injector is inserted through the center of the air swirler, with the fuel injector tip located near the venturi throat. All 7 fuel-air mixers are identical except for the swirler blade angle, which varies with the configuration. Testing was done in a 5-atm flame tube with inlet air temperatures from 600 to 800 F and equivalence ratios from 0.4 to 0.7. Combustion dynamics were measured using a cooled PCB pressure transducer flush-mounted in the wall of the combustor test section.

lean direct injection↗
NASA NTRS2015

An Assessment of Combustion Dynamics in a Low-Nox, Second-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

Dynamic pressure measurements were taken during flame-tube emissions testing of three second-generation swirl-venturi lean direct injection (SV-LDI) combustor configurations. These measurements show that combustion dynamics were typically small. However, a small number of points showed high combustion dynamics, with peak-to-peak dynamic pressure fluctuations above 0.5 psi. High combustion dynamics occurred at low inlet temperatures in all three SV-LDI configurations, so combustion dynamics were explored further at low temperature conditions. A point with greater than 1.5 psi peak-to-peak dynamic pressure fluctuations was identified at an inlet temperature of 450!F, a pressure of 100 psia, an air pressure drop of 3%, and an overall equivalence ratio of 0.35. This is an off design condition: the temperature and pressure are typical of 7% power conditions, but the equivalence ratio is high. At this condition, the combustion dynamics depended strongly on the fuel staging. Combustion dynamics could be reduced significantly without changing the overall equivalence ratio by shifting the fuel distribution between stages. Shifting the fuel distribution also decreased NOx emissions.

low emissions combustors↗
NASA NTRS2015

Effects of Burning Alternative Fuel in a 5-Cup Combustor Sector

A goal of NASA's Environmentally Responsible Aviation (ERA) program is to develop a combustor that will reduce the NOx emissions and that can burn both standard and alternative fuels. To meet this goal, NASA partnered with General Electric Aviation to develop a 5-cup combustor sector; this sector was tested in NASA Glenn's Advanced Subsonic Combustion Rig (ASCR). To verify that the combustor sector was fuel-flexible, it was tested with a 50-50 blend of JP-8 and a biofuel made from the camelina sativa plant. Results from this test were compared to results from tests where the fuel was neat JP-8. Testing was done at three combustor inlet conditions: cruise, 30% power, and 7% power. When compared to burning JP-8, burning the 50-50 blend did not significantly affect emissions of NOx, CO, or total hydrocarbons. Furthermore, it did not significantly affect the magnitude and frequency of the dynamic pressure fluctuations.

alternative fuel↗