Engineering topics

Tadas P. Bartkus

Publications and source records attributed to Tadas P. Bartkus.

5 records

NASA NTRSDate not supplied

A Study of Ice-Crystal Icing Erosion Using the NASA Icing Research Tunnel and Propulsion Systems Laboratory

In ice-crystal icing, ice erosion can occur simultaneously with ice accretion. This paper presents a proof-of-concept experimental study that attempts to isolate and quantify ice erosion. The experiments took place at the NASA Icing Research Tunnel and Propulsion Systems Laboratory in 2017 and 2018. The test procedure involved first generating an ice accretion on various NACA 0012 airfoil models using a supercooled liquid water or mixed-phase icing cloud and, subsequently, exposing that ice accretion to an ice crystal cloud. The resulting ice mass decay rates were analyzed in terms of an erosion term, defined as the ratio of the eroded mass flux to impinging mass flux. The erosion term generally increased with airspeed with a value of 1.8% at air velocities of 270 knots and increasing to just over 6% at 360 knots. A preliminary correlation for ice erosion is developed for use in ice accretion models subject to the conditions tested. The study revealed several challenges, both experimental and analytical, including spray bar nozzle freeze-out as well as measurement of the cloud melt ratio to ensure freeze-out.

Icing↗

NASA NTRSDate not supplied

Comparisons of CFD Simulations of Icing Wind Tunnel Clouds with Experiments Conducted at the NASA Propulsions Systems Laboratory

This paper evaluates simulation predictions against experimental test data of icing clouds that were produced during 2018 ice crystal icing physics tests conducted at the NASA Propulsion Systems Laboratory icing wind tunnel. Aero-thermal and cloud parameters are set and known upstream at the tunnel inlet and spray system, but change as the cloud and air thermodynamically interact as the flowing masses reach the tunnel test section. Utilizing the ANSYS Fluent Discrete Phase Model function, 3D computational fluid dynamics (CFD) simulations were performed, capturing the thermodynamic interactions between the test parameters, and providing predictions of the aero thermal and cloud conditions at the tunnel test section. Simulation predictions were compared with test data that were measured at the tunnel exit plane. Evaluations focused on the cloud concentration (total water content), humidity content, and air temperature. CFD simulation predictions showed areas of agreement and disagreement. Simulations showed that cloud concentration profiles at the test section are strongly related to the initial spray nozzle pattern used at the tunnel inlet. Experimental data suggest that greater dispersion of the cloud occurred as the simulated cloud predicted areas of high and low cloud concentration compared to test data profiles. Simulations, however, captured the magnitude and location of the change in humidity content and the change in air temperature due to the presence of the cloud reasonably well, when compared to test data. This result would suggest that while the ANSYS simulation did not fully predict the spreading of the cloud as measured during experiment, it did capture evaporation and the molecular movements of air and vapor relatively well.

CFD↗

NASA NTRSDate not supplied

Description of Cloud Characterization and Icing Tests for a 3D Heated Test Article at the NASA Icing Research Tunnel

This paper describes the cloud characterization and icing tests conducted with a 3D heated test article in Winter/Spring 2022 at the NASA Icing Research Tunnel. The intent is to present analyzed results from these recently conducted tests in a future technical paper. The test article, whose geometry is representative of an inter-compressor duct and strut region of a turbofan engine, has been designed and constructed to study the physics of supercooled water icing and ice crystal icing. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, a scale to measure ice mass, and other instruments will aid in characterizing the icing behavior. The aim of these tests is to generate ice accretions on the SIDRM test article under well-characterized conditions. To that end, a suite of instruments was utilized to characterize the ice crystal clouds at the test section in a separate test series. The icing measurements collected during the SIDRM model tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assess the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost effective way.

Ice crystal icing, heated test article, engine ici↗

NASA NTRSDate not supplied

Icing Physics Studies Using the 3D SIDRM Test Article: Aerodynamic and Supercooled Liquid Icing Analysis

In-flight icing is an important safety issue and is a factor that affects aircraft design and performance. Newer regulations are driving a need for improvements in airframe and engine icing simulation capability. Experimental data is required for development of icing physics models and simulation validation. To that end, this paper presents the analysis of the supercooled liquid icing data subset from tests conducted in 2022 at the NASA Icing Research Tunnel that studied both supercooled water and ice-crystal icing. The test article that was utilized replicated 3D geometrical features of an inter-compressor duct and strut region of a turbofan engine. The surfaces of the Simulated Inter-compressor Duct Research Model (SIDRM) can be heated to simulate the warm surfaces of the turbofan inter-compressor duct. The test article is instrumented with pressure taps, heaters, heat flux gauges, and thermocouples, while a 3D laser scanner, cameras, and a scale to measure ice mass were utilized to characterize the icing behavior. The aim of these tests was to generate ice accretions on the SIDRM test article under well-characterized supercooled liquid icing and ice crystal icing conditions. This paper discusses measurements related to aerodynamic testing and supercooled liquid icing tests that were conducted. Aerodynamic measurements were analyzed and compared to computational simulations and were found to be in good agreement for the range of airspeeds (50 to 230 knots) and angles of attack (0 to 4°) tested. Various parametric sweeps were conducted during the supercooled liquid icing portion of the test entry (cloud median volumetric diameter ranged from 15 to 90 µm, total air temperature from -3 to -17 °C, angle of attack from 0 to 4°, and accretion time from 5 to 20 min). These sweeps were performed to measure that parameter’s impact on ice accretion size, location (icing extent), characteristics (such as glaze/rime ice and shedding behavior), and test article surface temperature. Analysis of the test data showed that clouds composed of larger drops, colder air temperatures, smaller angles of attack, and longer spray times were the primary parameters that resulted in accretions with greater ice mass. Test article angle of attack and cloud droplet size influenced the location of ice accretion as these two parameters directly impact collection efficiency. With respect to icing characteristics, total air temperature dictated icing type, and smaller cloud drop size along with warmer air temperatures resulted in greater amounts of ice shedding. Surface temperature increased during ice accretion from the release of latent (fusion) heat, where total air temperature and cloud drop size impacted the amount of surface temperature change. The icing measurements collected during the SIDRM tests will be used to develop and validate 3D computational engine icing tools, such as GlennICE, that predictively assesses the onset and growth of ice. One of the goals of the sponsoring NASA project is to develop simulation models and tools that can assist in the design and certification of engines for flight in icing conditions in a cost effective way.

supercooled liquid icing↗

NASA NTRSDate not supplied

Computational Icing Analysis on NASA’s SIDRM Geometry to Investigate Collection Efficiency

Computational icing analysis results were compared to experimental icing tunnel data including aerothermal (e.g. dry air) and supercooled water droplet rime-ice conditions from tests conducted in early 2022 at the NASA Icing Research Tunnel (IRT). The Simulated Intercompressor Duct Research Model (SIDRM) test article was used in this study, and its geometry represents the inter-compressor duct region of a turbofan engine. The test article’s purpose is to study the physics of supercooled water icing and ice crystal icing. This study compared three different icing codes: FENSAP-ICE (Eulerian approach), LEWICE3D (Lagrangian approach), and GlennICE (Lagrangian approach). All three icing codes were conducted on SIDRM’s complex body flow-field and compared to different experimental supercooled water rime runs. The test article instrumentation (pressure taps, thermocouples, etc.) and 3D laser scans of final ice shapes were used to compare against the different icing code simulations. The overall objectives are to understand how the icing codes handle capturing collection efficiency on the complex test article’s unheated surfaces. In the aerothermal cases, pressure tap readings matched the CFD results, but dry air CFD underpredicted thermocouple readings. Collection efficiency results from all three icing codes matched well together on the main body leading edge, main body slope, and the strut leading edges. All three icing codes underpredicted the final ice shape using a single-shot constant ice density approach, with more difficulty coming from the strut leading edge ice shape due to the swept wing like flow field. NASA’s overall goal for this effort is to develop computational icing tools to assist in the design and certification of engines for flight in icing conditions.

Supercooled icing, SIDRM, aerodynamics, computatio↗