Hydrogen-Induced Topotactic Phase Transformations of Cobaltite Thin Films
Not Available
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Engineering topics
Takamura, Yayoi
Publications and source records attributed to Takamura, Yayoi.
Electrical Control of Magnetic Resonance in Phase Change Materials
Metal–insulator transitions (MITs) in resistive switching materials can be triggered by an electric stimulus that produces significant changes in the electrical response. When these phases have distinct magnetic characteristics, dramatic changes in the spin excitations are also expected. The transition metal oxide La 0.7 Sr 0.3 MnO 3 (LSMO) is a ferromagnetic metal at low temperatures and a paramagnetic insulator above room temperature. When LSMO is in its metallic phase, a critical electrical bias has been shown to lead to an MIT that results in the formation of a paramagnetic resistive barrier transverse to the applied electric field. Using spin-transfer ferromagnetic resonance spectroscopy, we show that even for electrical biases less than the critical value that triggers the MIT, there is magnetic phase separation, with the spin-excitation resonances varying systematically with applied bias. Therefore, voltage-triggered MITs in LSMO can alter magnetic resonance characteristics, offering an effective method for tuning synaptic weights in neuromorphic circuits.
36 MATERIALS SCIENCE↗
Local strain inhomogeneities during electrical triggering of a metal–insulator transition revealed by X-ray microscopy
Electrical triggering of a metal–insulator transition (MIT) often results in the formation of characteristic spatial patterns such as a metallic filament percolating through an insulating matrix or an insulating barrier splitting a conducting matrix. When MIT triggering is driven by electrothermal effects, the temperature of the filament or barrier can be substantially higher than the rest of the material. Using X-ray microdiffraction and dark-field X-ray microscopy, we show that electrothermal MIT triggering leads to the development of an inhomogeneous strain profile across the switching device, even when the material does not undergo a pronounced, discontinuous structural transition coinciding with the MIT. Diffraction measurements further reveal evidence of unique features associated with MIT triggering including lattice distortions, tilting, and twinning, which indicate structural nonuniformity of both low- and high-resistance regions inside the switching device. Such lattice deformations do not occur under equilibrium, zero-voltage conditions, highlighting the qualitative difference between states achieved through increasing temperature and applying voltage in nonlinear electrothermal materials. Electrically induced strain, lattice distortions, and twinning could have important contributions in the MIT triggering process and drive the material into nonequilibrium states, providing an unconventional pathway to explore the phase space in strongly correlated electronic systems.
42 ENGINEERING↗
Spin-flop coupling at La 0.5 Sr 0.5 FeO 3 /La 0.7 Sr 0.3 MnO 3 interfaces
Antiferromagnetic (AFM) spintronics offer several benefits compared to their ferromagnetic (FM) counterparts, such as high storage capacity and faster processing speed, however, difficulties in manipulating and detecting the AFM moments impede their implementation. Spin-flop coupling, the interfacial perpendicular coupling between FM and AFM moments, can be utilized to control the orientation of AFM moments with the application of moderate magnetic fields on the scale of tenths of a Tesla. Here, in this work, epitaxial bilayers of AFM La 0.5 Sr 0.5 FeO 3 (LSFO)/FM La 0.7 Sr 0.3 MnO 3 (LSMO) with fixed LSMO thickness (~85 u.c.) and LSFO thicknesses varying from 10 to 50 u.c. were investigated to determine the effect of Sr doping and La 1-x Sr x FeO 3 magnetocrystalline anisotropy on the strength of spin-flop coupling. X-ray magnetic linear dichroism demonstrated that the spin-flop coupling strength decreased with increasing LSFO layer thickness, persisting at a thickness of 50 u.c. (~20 nm). Furthermore, photoemission electron microscopy revealed a domain-by-domain correlation between the FM and AFM domains consistent with the perpendicular orientation dictated by spin-flop coupling. These results demonstrate that LSFO/LSMO bilayers have the potential to serve as a model materials system for AFM spin transport measurements.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Magnetoresistance anomaly during the electrical triggering of a metal-insulator transition
Phase separation naturally occurs in a variety of magnetic materials and it often has a major impact on both electric and magnetotransport properties. In resistive switching systems, phase separation can be created on demand by inducing local switching, which provides an opportunity to tune the electronic and magnetic state of the device by applying voltage. Here we explore the magnetotransport properties in the ferromagnetic oxide La 0.7 Sr 0.3 MnO 3 (LSMO) during the electrical triggering of an intrinsic metal-insulator transition (MIT), which produces volatile resistive switching. This switching occurs in a characteristic spatial pattern, i.e., the formation of a high-resistance barrier perpendicular to the current flow, enabling an electrically actuated ferromagnetic-paramagnetic-ferromagnetic phase separation. At the threshold voltage of the MIT triggering, both anisotropic and colossal magnetoresistances exhibit anomalies including a large increase in magnitude and a sign flip. Computational analysis revealed that these anomalies originate from the coupling between the switching-induced phase separation state and the intrinsic magnetoresistance of LSMO. Furthermore, this work demonstrates that driving the MIT material into an out-of-equilibrium resistive switching state provides the means for electrical control of the magnetotransport phenomena.
Complex oxides↗
Tuning In-Plane Magnetic Anisotropy and Interfacial Exchange Coupling in Epitaxial La 2/3 Sr 1/3 CoO 3 /La 2/3 Sr 1/3 MnO 3 Heterostructures
Controlling the in-plane magnetocrystalline anisotropy and interfacial exchange coupling between ferromagnetic (FM) layers plays a key role in next-generation spintronic and magnetic memory devices. In this work, we explored the effect of tuning the magnetocrystalline anisotropy of La 2/3 Sr 1/3 CoO 3 (LSCO) and La 2/3 Sr 1/3 MnO 3 (LSMO) layers and the corresponding effect on interfacial exchange coupling by adjusting the thickness of the LSCO layer (t LSCO ). The epitaxial LSCO/LSMO bilayers were grown on (110) o -oriented NdGaO 3 (NGO) substrates with a fixed LSMO (top layer) thickness of 6 nm and LSCO (bottom layer) thicknesses varying from 1 to 10 nm. Despite the small difference (~0.2%) in lattice mismatch between the two in-plane directions, [001] o and [11̅0] o , a pronounced in-plane magnetic anisotropy was observed. Soft X-ray magnetic circular dichroism hysteresis loops revealed that for t LSCO ≤ 4 nm, the easy axes for both LSCO and LSMO layers were along the [001] o direction, and the LSCO layer was characterized by magnetically active Co 2+ ions that strongly coupled to the LSMO layer. No exchange bias effect was observed in the hysteresis loops. In contrast, along the [11̅0] o direction, the LSCO and LSMO layers displayed a small difference in their coercivity values, and a small exchange bias shift was observed. As t LSCO increased above 4 nm, the easy axis for the LSCO layer remained along the [100] o direction, but it gradually rotated to the [11̅0] o direction for the LSMO layer, resulting in a large negative exchange bias shift. Therefore, we provide a way to control the magnetocrystalline anisotropy and exchange bias by tuning the interfacial exchange coupling between the two FM layers.
36 MATERIALS SCIENCE↗
Voltage-controlled magnetic anisotropy enabled by resistive switching
The discovery of new mechanisms of controlling magnetic properties by electric fields or currents furthers the fundamental understanding of magnetism and has important implications for practical use. Here, we present an approach of utilizing resistive switching to control magnetic anisotropy. We study a ferromagnetic oxide that exhibits an electrically triggered metal-to-insulator phase transition producing a volatile resistive switching. The switching occurs in a characteristic spatial pattern, the formation of an insulating barrier perpendicular to the current flow, which results in an unusual ferromagnetic/paramagnetic/ferromagnetic configuration. Further, the formation of this voltage-driven paramagnetic insulating barrier is accompanied by the emergence of a strong uniaxial magnetic anisotropy that overpowers the intrinsic material anisotropy. Our results demonstrate that resistive switching is an effective tool for manipulating magnetic properties. Because resistive switching can be induced in a broad range of materials, our findings could enable a new class of voltage-controlled magnetism systems.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Strain- and thickness-dependent magnetic properties of epitaxial La 0.67 Sr 0.33 CoO 3 /La 0.67 Sr 0.33 MnO 3 bilayers
Magnetic properties and interfacial phenomena of epitaxial perovskite oxides depend sensitively on parameters such as film thickness and strain state. In this work, epitaxial La0 .67 Sr 0.33 CoO 3 (LSCO)/La 0.67 Sr 0.33 MnO 3 (LSMO) bilayers were grown on NdGaO 3 (NGO) and LaAlO 3 (LAO) substrates with a fixed LSMO thickness of 6 nm, and LSCO thickness (t LSCO ) varying from 2 to 10 nm. Soft x-ray magnetic spectroscopy revealed that magnetically active Co 2+ ions that strongly coupled to the LSMO layer were observed below a critical t LSCO for bilayers grown on both substrates. On LAO substrates, this critical thickness was 2 nm, above which the formation of Co 2+ ions was quickly suppressed leaving only a soft LSCO layer with mixed valence Co 3+ /Co 4+ ions. The magnetic properties of both LSCO and LSMO layers displayed strong t LSCO dependence. This critical t LSCO increased to 4 nm on NGO substrates, and the magnetic properties of only the LSCO layer displayed t LSCO dependence. A non-magnetic layer characterized by Co 3+ ions and with a thickness below 2 nm exists at the LSCO/substrate interface for both substrates. Therefore, the results contribute to the understanding of interfacial exchange spring behavior needed for applications in next generation spintronic and magnetic memory devices.
36 MATERIALS SCIENCE↗
Quantum materials for energy-efficient neuromorphic computing: Opportunities and challenges
Neuromorphic computing approaches become increasingly important as we address future needs for efficiently processing massive amounts of data. The unique attributes of quantum materials can help address these needs by enabling new energy-efficient device concepts that implement neuromorphic ideas at the hardware level. In particular, strong correlations give rise to highly non-linear responses, such as conductive phase transitions that can be harnessed for short- and long-term plasticity. Similarly, magnetization dynamics are strongly non-linear and can be utilized for data classification. This Perspective discusses select examples of these approaches and provides an outlook on the current opportunities and challenges for assembling quantum-material-based devices for neuromorphic functionalities into larger emergent complex network systems.
36 MATERIALS SCIENCE↗
Formation of Complex Spin Textures in Thermally Demagnetized La 0.7 Sr 0.3 Mn O 3 Artificial-Spin-Ice Structures
Artificial spin ices (ASIs) have traditionally been designed such that each nanomagnet possesses a single-domain magnetic configuration that is assumed to be minimally perturbed by interisland dipolar interactions. Using x-ray photoemission electron microscopy to perform magnetic domain imaging, we study thermally demagnetized La 0.7 Sr 0.3 MnO 3 -based brickwork ASI arrays and showed that complex spin textures (CSTs) can be stabilized through an appropriate selection of nanoisland width and interisland spacing. While the width dependence can be explained through the dominance of shape anisotropy in isolated nanoislands, the ASIs we investigate demonstrate a complex dependence on both the nanoisland width and interisland spacing. Micromagnetic simulations reveal that interisland dipolar interactions play a role in the formation of CSTs, which are composed of single- and double-vortex states. Furthermore, energy analysis of the simulations provides an understanding of the system energetics that arises from a delicate balance between intraisland effects (i.e., shape anisotropy and exchange energy) and interisland effects (i.e., dipolar interactions between nearest-neighbor nanoislands).
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Determining the Oxygen Stoichiometry of Cobaltite Thin Films
Transition metal oxides (TMO) are promising materials to realize low-power neuromorphic devices. Their physical properties critically depend on their oxygen vacancy concentrations, whose experimental determination remains a challenging task. Here we focus on cobaltites, in particular La 1-x Sr x CoO 3-d (LSCO), and we present a strategy to identify fingerprints of oxygen vacancies in X-ray absorption (XA) spectra. Using a combination of experiment and theory, we show that the variation of the oxygen vacancy concentration in the perovskite phase of LSCO is correlated with the change of the relative peak positions of the O K-edge XA spectra. Furthermore, we also identify an additional geometrical fingerprint that captures both the changes of the Co-O bond length and Co-O-Co bond angle in the material due to the presence of oxygen vacancies. Finally, we predict the oxygen vacancy concentration of experimental samples and show how the resistivity of the oxide material may be tuned as a function of the defect concentration present in the system.
36 MATERIALS SCIENCE↗
Transverse barrier formation by electrical triggering of a metal-to-insulator transition
Application of an electric stimulus to a material with a metal-insulator transition can trigger a large resistance change. Resistive switching from an insulating into a metallic phase, which typically occurs by the formation of a conducting filament parallel to the current flow, is a highly active research topic. Using the magneto-optical Kerr imaging, we found that the opposite type of resistive switching, from a metal into an insulator, occurs in a reciprocal characteristic spatial pattern: the formation of an insulating barrier perpendicular to the driving current. This barrier formation leads to an unusual N-type negative differential resistance in the current-voltage characteristics. We further demonstrate that electrically inducing a transverse barrier enables a unique approach to voltage-controlled magnetism. By triggering the metal-to-insulator resistive switching in a magnetic material, local on/off control of ferromagnetism is achieved using a global voltage bias applied to the whole device.
36 MATERIALS SCIENCE↗
Cation and anion topotactic transformations in cobaltite thin films leading to Ruddlesden-Popper phases.
Topotactic transformations involve structural changes between related crystal structures due to a loss or gain of material while retaining a crystallographic relationship. The perovskite oxide La0.7Sr0.3CoO3 (LSCO) is an ideal system for investigating phase transformations due to its high oxygen vacancy conductivity, relatively low oxygen vacancy formation energy, and strong coupling of the magnetic and electronic properties to the oxygen stoichiometry. While the transition between cobaltite perovskite and brownmillerite (BM) phases has been widely reported, further reduction beyond the BM phase lacks systematic studies. In this paper, we study the evolution of the physical properties of LSCO thin films upon exposure to highly reducing environments. We observe the rarely reported crystalline Ruddlesden-Popper phase, which involves the loss of both oxygen anions and cobalt cations upon annealing where the cobalt is found as isolated Co ions or Co nanoparticles. First-principles calculations confirm that the concurrent loss of oxygen and cobalt ions is thermodynamically possible through an intermediary BM phase. The strong correlation of the magnetic and electronic properties to the crystal structure highlights the potential of utilizing ion migration as a basis for emerging applications such as neuromorphic computing.
Chiu, I-Ting↗
Hidden transformations in entropy-stabilized oxides
We report entropy-stabilized oxides (ESO) display a reversible entropy-driven phase transformation that can be leveraged to produce a continuum of metastable phase states, allowing for property optimization and novel functionalities. X-ray absorption spectroscopy reveals that entropic stabilization extends to the electronic structure (valence state and cation coordination) in sintered (Co,Cu,Mg,Ni,Zn)O, manifesting as a tunable lattice distortion in the entropy-stabilized phase. Co, Cu, and Zn ions reversibly transform from six-fold to four-fold coordinated structures and from low to high valence states due to the competition between electronic structures that are equilibrium and enthalpy-driven or metastable and entropy-driven. The segregation of a Cu-rich tenorite phase and a Co-rich spinel phase influences the electronic structure evolution. ESOs can adjust their electronic structures through heat treatment, providing a powerful tool for developing functional properties. These results indicate that the definition of entropy stabilization should include entropy-stabilized electronic structures, providing motivation to reassess previously studied HEO materials.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗