Freeze-Thaw Engineered Dual Conductivity Polymeric Binder Stabilizes Large-Volume-Change Lithium–Ion Battery Anodes
Explore the source record for details and available documents.
36 MATERIALS SCIENCE↗
Engineering topics
Takeuchi, Kenneth J.
Publications and source records attributed to Takeuchi, Kenneth J..
Impact of Synthetic Parameters on Structure and Electrochemistry of High-Entropy Layered Oxide LiNi 0.2 Co 0.2 Mn 0.2 Al 0.2 Fe 0.2 O 2
Here, this study explored a high-entropy layered oxide (HELO), LiNi 0.2 Co 0.2 Mn 0.2 Al 0.2 Fe 0.2 O 2 , prepared by coprecipitation followed by heat treatment. Coprecipitation yielded a kinetically favored product, and the subsequent heat treatment under various temperatures and times allowed tuning the material toward more thermodynamically favored structures. Refinement of X-ray powder diffraction (XRD) revealed that after 450 °C treatment, ~12% of the Ni 2+ in the structure was located within the lithium cation layer. After heat treatment at 600, 700, and 800 °C, there was a continued decrease of Ni 2+ in the lithium cation layer to 9.3, 6.3, and 3.7%, respectively. Longer heat treatment times at 800 °C decreased the level to 2.5%. Electrochemical behavior was evaluated by cyclic voltammetry, galvanostatic cycling, rate capability testing, and electrochemical impedance spectroscopy, where increased loaded voltage, functional capacity, rate capability, and decreased impedance were observed for samples treated at higher temperatures with lower cation mixing. X-ray absorption near edge spectroscopy (XANES) data indicated that the redox activity of Ni and Co was dominant in the electrochemistry, while the participation of Mn or Fe was minimal. The level of Ni oxidation state change between charge and discharge related to the heat treatment temperature where the samples with high cation mixing showed lower capacity consistent with some Ni 3+ in the transition metal layer inaccessible for electron transfer. Longer heat treatment times at 800 °C did not continue to provide a benefit in electrochemical function even with some additional reduction in cation mixing.
25 ENERGY STORAGE↗
Elucidating the Discharge Behavior of Aqueous Zinc Sulfur Batteries in the Presence of Molybdenum(IV) Chalcogenide Catalyst: The Criticality of Interfacial Electrochemistry
The aqueous zinc-sulfur battery holds promise for significant capacity and energy density with low cost and safe operation based on environmentally benign materials. However, it suffers from the sluggish kinetics of the conversion reaction. Here, we highlight the efficacy of molybdenum(IV) sulfide (MoS 2 ) to reduce the overpotential of S-ZnS conversion in aqueous electrolytes and study the discharge products formed at the solid-solid and solid-liquid interfaces using experimental and theoretical approaches. Specifically, the MoS 2 -catalyzed electrochemical conversion reaction is characterized via ex situ X-ray diffraction (XRD), transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS), Raman spectroscopy, synchrotron-based Mo K-edge X-ray absorption spectroscopy (XAS), and in situ synchrotron-based X-ray computed tomography (XCT). Additionally, operando synchrotron-based S K-edge XAS and X-ray fluorescence (XRF) maps are collected to determine the spatial evolution of sulfur-based species at the electrode-electrolyte interface. Further, coupling the operando S K-edge XAS data with the simulated spectra and fitting the data suggested a possible ZnS 2 intermediate phase.
25 ENERGY STORAGE↗
Fully Fluorinated Local High Concentration Electrolytes Enabling High Energy Density Si Anodes
To develop fluorinated localized high concentration electrolytes as a novel approach for constructing a functional SEI on Si based anodes. The technological approach combines the SEI modification strategies of fluorinated carbonate solvents and local high concentration electrolytes. The resulting synergy of anion and fluorinated solvent decomposition will form a mechanically robust, fluorinated SEI that enables extended cycling with high capacity retention. The electrolytes will enable demonstration of silicon-graphite anodes with high Si content, paired with NMC811 cathodes. Characterization will focus on galvanostatic cycling to evaluate electrochemical performance.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Magnetically oriented nanosheet interlayer for dynamic regeneration in lithium metal batteries
Lithium (Li) metal has been recognized as a promising anode to advance the energy density of current Li-based batteries. However, the growth of the solid–electrolyte interphase (SEI) layer and dendritic Li microstructure pose significant challenges for the long-term operation of Li metal batteries (LMBs). Herein, we propose the utilization of a suspension electrolyte with dispersed magnetically responsive nanosheets whose orientation can be manipulated by an external magnetic field during cell operation for realizing in situ regeneration in LMBs. The regeneration mechanism arises from the redistribution of the ion flux and the formation of an inorganic-rich SEI for uniform and compact Li deposition. With the magnetic-field-induced regeneration process, we show that a Li||Li symmetric cell stably operates for 350 h at 2 mA cm −2 and 2 mA h cm −2 , ~5 times that of the cell with the pristine electrolyte. Furthermore, the cycling stability can be significantly extended in the Li||NMC full cell of 3 mA h cm −2 , showing a capacity retention of 67% after 500 cycles at 1C. The dynamic Li metal regeneration demonstrated here could bring useful design considerations for reviving the operating cells for achieving high-energy, long-duration battery systems.
Ju, Zhengyu↗
In Situ Alloying Enabled by Active Liquid Metal Filler for Self‐Healing Composite Polymer Electrolytes
Abstract Solid inorganics, known for kinetically inhibiting polymer crystallization and enhancing ionic conductivity, have attracted significant attention in solid polymer electrolytes. However, current composite polymer electrolytes (CPEs) are still facing challenges in Li metal batteries, falling short of inhibiting severe dendritic growth and resulting in very limited cycling life. This study introduces Ga 62.5 In 21.5 Sn 16 (Galinstan) liquid metal (LM) as an active liquid alternative to conventional passive solid fillers, aiming at realizing self‐healing protection against dendrite problems. Compared to solid inorganics, for example silica, LM droplets could more significantly reduce polymer crystallinity and enhance Li‐ion conductivity due to their liquid nature, especially at temperatures below the polymer melting point. More importantly, LMs are unraveled as dynamic chemical traps, which are capable of blocking and consuming lithium dendrites upon contact via in situ alloying during battery operation and further inhibiting dendritic growth due to the lower deposition energy barrier of the formed Li‐LM alloy. As a proof of concept, by strategically designing an asymmetric CPE with the active LM filling, a solid‐state Li/LiFePO 4 battery achieves promising full‐cell functionality with notable rate performance and stable cycle life. This active filler‐mediated self‐healing approach could bring new insights into the battery design in versatile solid‐state systems.
Wu, Kai↗
Electrochemistry Beyond Solutions: Modeling Particle Self-Crowding of Nanoparticle Suspensions
Not Available
25 ENERGY STORAGE↗
Lithium-ion battery functionality over broad operating conditions via local high concentration fluorinated ester electrolytes
Delivered capacities of non-flammable LHCE vs. flammable LiPF 6 EC:DMC electrolyte at low temperature, high voltage charge, and fast charge.
25 ENERGY STORAGE↗
Manganese-rich high entropy oxides for lithium-ion batteries:materials design approaches to address voltage fade
Lithium- and manganese-rich oxides are of interest as lithium-ion battery cathode materials as Mn is earth abundant, low cost, and can deliver high capacity. Herein, a high entropy strategy was used to prepare Mn rich high entropy oxide (HEO) materials by including four additional metals (Ni, Co, Fe and Al) in the compositions using a mild co-precipitation method. Two HEOs (Li x Ni 0.1 Mn 0.6 Co 0.1 Al 0.1 Fe 0.1 O y , where x = 1.5 for HEO-L and x = 0.5 for HEO-H) with layered and spinel-layered hybrid structures were investigated where the morphology, elemental composition, structure, atomic level phase distribution, and electrochemistry were determined. The HEO-L samples involve a Li 2 TMO 3 layered structure with ~39% stacking faults. HEO-H is a hybrid structure comprised of 80 wt% spinel and 20 wt% LiMO 2 layered structure. The high entropy manganese-rich HEO-L showed higher capacity and 93% retention of the average voltage after 100 cycles while HEO-H showed higher capacity retention and near 100% average voltage retention. Finally, operando X-ray absorption spectroscopy revealed that the Ni, Co, and Mn are redox active in both materials while the Fe center remains at the Fe 3+ oxidation state throughout cycling, where the changes in the oxidation states for both materials during discharge were consistent with the delivered electrochemical capacity rationalizing the observed electrochemistry.
25 ENERGY STORAGE↗
Identifying point defects and ordering in the high-entropy layered oxide Li 1.5 MO 3-δ (M=Mn, Al, Fe, Co, Ni) for energy storage applications
High-entropy layered oxides (HELOs) represent a very promising class of next-generation battery cathodes, combining the well-studied properties of layered cathode materials such as LiCoO 2 with the chemical tunability and stability of high-entropy materials. HELO materials often form particles with complex defects and domain structures, complicating accurate characterization of structure and cation mixing. Understanding disorder and order in HELO materials is necessary for understanding their performance and utility as cathodes. Here we demonstrate the characterization of the HELO Li 1.5 MO 3-δ (M = Mn, Al, Fe, Co, Ni), wherein X-ray powder diffraction, transmission electron microscopy imaging, and electron diffraction patterns are analyzed to reveal the presence of ordering in the HELO, with imaging and diffraction simulation employed to compare experimental results to atomic modeling. Finally, without rigorous characterization at the atomic scale, important features such as defect ordering can be easily overlooked and therefore remain unconsidered when interpreting experimental results.
36 MATERIALS SCIENCE↗
Defect-Driven Configurational Entropy in the High-Entropy Oxide Li 1.5 MO 3-δ
Layered lithiated oxides are promising materials for next generation Li-ion battery cathode materials; however, instability during cycling results in poor performance over time compared to the high capacities theoretically possible with these materials. Here, in this paper, we report the characterizations of a Li 1.47 Mn 0.57 Al 0.13 Fe 0.095 Co 0.105 Ni 0.095 O 2.49 high-entropy layered oxide (HELO) with the Li 2 MO 3 structure where M = Mn, Al, Fe, Co, and Ni. Using electron microscopy and X-ray spectroscopy, we identify a homogeneous Li 2 MO 3 structure stabilized by the entropic contribution of oxygen vacancies. This defect-driven entropy would not be attainable in the LiMO 2 structure sometimes observed in similar materials as a secondary phase owing to the presence of fewer O sites and a 3+ oxidation state for the metal site; instead, a Li 2-γ MO 3-δ is produced. Beyond Li 2 MO 3 , this defect-driven entropy approach to stabilizing novel compositions and phases can be applied to a wide array of future cathode materials including spinel and rock salt structures.
25 ENERGY STORAGE↗
Rational optimization of substituted α–MnO 2 cathode for aqueous zinc–ion battery
Density functional theory (DFT) is utilized to explore the effects of increasing concentrations of vanadium (V) and chromium (Cr) substitution on the discharge of α-MnO 2 cathode in hydrated zinc-ion batteries (ZIBs). During H + -intercalation and Zn 2+ -intercalation, Cr-substitution proves to be more effective than V-substitution in promoting discharge behaviors. Transitioning from Mn 0.875 Cr 0.125 O 2 , Mn 0.75 Cr 0.25 O 2 to Mn 0.625 Cr 0.375 O 2 is found to consistently enhance the discharge voltage, along with improved tunnel structure retention and volume expansion suppression. In comparison, the promoting effect of increasing V-substitution is relatively small at initial discharge stages and leads to degradation at later stages, primarily due to an increased concentration of unstable Mn 2+ ion. The superior effect of Cr-substitution is attributed to the unique atomic and electronic structures of substituted Cr 4+ and reduced Cr 3+ ions during discharge. These ions serve as active electron acceptors to limit the formation of Mn 3+ and Mn 2+ ions, and as anchors to stabilize the α-MnO 2 framework and intercalated H + /Zn 2+ ions, respectively. Finally, our study highlights fine-tuning through substitution to enhance the performance of α-MnO 2 -based cathode materials in ZIBs.
25 ENERGY STORAGE↗
Synthetic methods for crystallite size control of bimetallic polyanionic battery compositions
Bimetallic polyanionic materials, such as silver vanadium phosphorus oxide (Ag 2 VO 2 PO 4 , SVOP), are promising cathode materials for Li batteries due in part to their large capacity and high current capability. A new synthesis of Ag 2 VO 2 PO 4 based on microwave heating is disclosed, where the reaction time is reduced by approximately 100 times relative to other reported methods, and the crystallite size is controlled via synthesis temperature, showing a linear positive correlation of crystallite size with temperature. Reaction times of an hour or less are sufficient to render phase-pure material after reaction at 50° C. to 180° C., significantly lower than the temperatures reported for other methods. Crystallite sizes between 42 nm and 60 nm are achieved by the novel method, smaller than by other methods. Silver/vanadium atomic ratios of 1.96 to 2.04 in the as-synthesized SVOP result and appear temperature-dependent. Notably, under galvanostatic reduction, the Ag 2 VO 2 PO 4 sample with the smallest crystallite size delivers the highest capacity and shows the highest loaded voltage.
Takeuchi, Kenneth J.↗
A framework for integrating supply chain, environmental, and social justice factors during early stationary battery research
The transition to a decarbonized economy will drive dramatically higher demand for energy storage, along with technological diversification. To avoid mistakes of the past, the supply chain implications and environmental and social justice (ESJ) impacts of new battery technologies should be considered early during technological development. We propose herein a systematic framework for analyzing these impacts for new stationary battery technologies and illustrate the framework with a case study. The goal is to promote future development of technologies with secure supply chains and favorable ESJ profiles to avoid expensive corrective actions after substantial resources have been invested. This framework should be a useful tool for public and private researchers and sponsors who want to ensure that supply chain and ESJ concerns are considered and integrated as part of decision making throughout the research and development process.
29 ENERGY PLANNING, POLICY, AND ECONOMY↗
Origin of Phase Separation in Ni-Rich Layered Oxide Cathode Materials During Electrochemical Cycling
In intercalation materials, the kinetics and uniformity of mass transport across the nanocrystalline domains dictate the structural reversibility and transport capability at the macroscopic level. (De)intercalation-induced interlayer disintegrations exhibit anisotropic crystallite size change. Due to the anisotropic mass transport mechanism, separated phases are inherently crystallographically oriented. One such material is LiNi $1–x–y$ Mn $x$ Co $y$ O 2 , which plays a pivotal role in advanced Li-ion batteries but suffers from severe phase inhomogeneities under fast charge or electrochemical aging. Here, using operando synchrotron techniques, we probe the mechanistic origins of the compositional and orientational-dependent phase separations during the electrochemical cycling of LiNi 0.8 Mn 0.1 Co 0.1 O 2 by comprehensive analysis of both in-plane and out-of-plane reflections. In the H2/H3 phase regime, in-plane domain propagation occurs due to increased covalency despite the severe decay of interlayer crystallographic order, resulting in the change of crystalline domain shape from 3D spheres to two-dimensional nanosheets. The crystallographically selective XRD line splitting is linked to the geometry of the facets as mass transfers along the ab plane. In conclusion, this work provides mechanistic insights into crystallographic orientation-dependent phase inhomogeneity under fast charge and extended cycling.
36 MATERIALS SCIENCE↗