Search NASA⌕ Search

Engineering topics

Tan, Chuting

Publications and source records attributed to Tan, Chuting.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

First-of-a-Kind Fuel-bearing Molten Chloride Irradiation Experiment

As a dozen MSR developers in the U.S. work toward an aggressive commercialization timeline, many of their fueled-salts—notably, chloride-based compositions—have never been irradiated. Licensing and operating these reactors requires an understanding of (1) the source term, radiation chemistry, and gas generation; (2) unanticipated irradiation-induced corrosion effects; and (3) the impact of burnup on thermophysical properties, all of which can be deduced through irradiation testing. Idaho National Laboratory (INL) is ideally suited to leverage its expertise in chloride salt chemistry, as well as its Neutron Radiography Reactor (NRAD) facility in the Hot Fuels Examination Facility (HFEF) at the Materials and Fuels Complex (MFC), to conduct the world’s first fuel-bearing chloride salt irradiation and fill in the knowledge gaps pertaining to salt chemistry under irradiation. Molten-salt Research Temperature-controlled Irradiation (MRTI) consists of a salt-containing capsule that is internally heated inside of a secondary containment. The experiment must rely on resistive heating to melt the salt before irradiation (to avoid the impact of radiolysis) and once the reactor is turned on and fission reactions commence in the salt, the resistive power can then be reduced. Salt-immersed thermocouples coupled to a controller allow for the heater power to be adjusted as needed to meet experimental objectives. The bulk of the experimental results will be achieved through Post-Irradiation Examination (PIE). At which point a range of different measurements are anticipated to assess the salt/plenum/wall composition, the capsule corrosion rate, and the evolution of salt properties.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Design and testing of an enriched uranium fueled molten salt irradiation vehicle

Molten salt reactors (MSRs) have garnered increasing attention recently with several demonstration efforts on the way. A key challenge to the licensing basis for these reactors is the lack of experimental data on fueled salts. This is expected to be crucial to the safety evaluation and licensing basis of reactors of this type deployed in the future. While capability for irradiating molten salts has started being reestablished in the recent decade, no enriched fuel irradiation capability has been developed and tested as of yet. A new experiment vehicle under development at Idaho National Laboratory (INL) is presented here. The Molten-salt Research Temperature-controlled Irradiation (MRTI) experiment was developed to host enriched-uranium bearing salt samples to be irradiated at a test reactor within the lab complex. One of the key scientific objectives is to provide irradiated salt samples for post irradiation examination (PIE) to study the impact of fission product generation and neutron/gamma radioactivity on the salt solution and salt-facing wall material. This paper provides a detailed overview of the mechanical design of the experiment, followed by an overview of the fabrication and assembly of an initial prototype vehicle (with non-fuel bearing salt). A summary of the key analyses conducted as a part of the performance and safety evaluation is then provided. Lastly, an overview of the test conducted in prototypic out-of-pile (non-neutron) environment are shown. These evaluations provide the foundation for a planned irradiation of and enriched uranium-bearing chloride salt sample in the near term. The upcoming irradiation will contain 13cm 3 of UCl 3 -NaCl salt (93% enrichment) generating around 20 W/cm 3 of fission energy during irradiation and a temperature range that can be contained between bounds of 525-900°C.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

CDB-AP: An application for coincidence Doppler broadening spectroscopy analysis

Coincidence Doppler Broadening (CDB) Positron Annihilation Spectroscopy (PAS) is a material analysis technique that can be used to non-destructively measure characteristics of structural defects in samples. Analyzing and comparing large datasets obtained using this technique, however, can be complicated and time intensive. The Coincidence Doppler Broadening Analysis Program (CDB-AP) is a graphical user interface that facilitates rapid analysis of many data files while using transparent processes. It is already used in three laboratories at Idaho National Laboratory and can be used in laboratories worldwide.

36 MATERIALS SCIENCE↗
DOE OSTI2023

The Complex, Unique, and Powerful Imaging Instrument for Dynamics (CUPI 2 D) at the Spallation Neutron Source (invited)

The Oak Ridge National Laboratory is planning to build the Second Target Station (STS) at the Spallation Neutron Source (SNS). STS will host a suite of novel instruments that complement the First Target Station’s beamline capabilities by offering an increased flux for cold neutrons and a broader wavelength bandwidth. A novel neutron imaging beamline, named the Complex, Unique, and Powerful Imaging Instrument for Dynamics (CUPI 2 D), is among the first eight instruments that will be commissioned at STS as part of the construction project. CUPI 2 D is designed for a broad range of neutron imaging scientific applications, such as energy storage and conversion (batteries and fuel cells), materials science and engineering (additive manufacturing, superalloys, and archaeometry), nuclear materials (novel cladding materials, nuclear fuel, and moderators), cementitious materials, biology/medical/dental applications (regenerative medicine and cancer), and life sciences (plant–soil interactions and nutrient dynamics). The innovation of this instrument lies in the utilization of a high flux of wavelength-separated cold neutrons to perform real time in situ neutron grating interferometry and Bragg edge imaging—with a wavelength resolution of δλ/λ ≈ 0.3%—simultaneously when required, across a broad range of length and time scales. This manuscript briefly describes the science enabled at CUPI 2 D based on its unique capabilities. The preliminary beamline performance, a design concept, and future development requirements are also presented.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Design and Fabrication of a Temperature-Controlled Fueled Molten Salt Capsule Irradiation Experiment

Idaho National Laboratory (INL) is developing a Molten salt Research Temperature-controlled Irradiation (MRTI) experimental capsule for the Neutron Radiography (NRAD) reactor. The experiment is envisaged to be versatile and able to host a variety of salt-wall material combinations. The first test is designed to contain actinide-bearing chloride salt, which previously has not been subjected to a neutron field. The main objectives of the experiment are to produce irradiated salt samples for Post Irradiation Examination (PIE), to evaluate salt behavior under irradiation, and to test in-situ sensors/instrumentation. The final design for the experiment completed in 2022, and fabrication of the experiment is underway. The salt is double encapsulated providing insulation and redundancy in the case of leakage. A gas-gap between the inner capsule and the outer container enables tuning of thermal conduction to the NRAD coolant by altering its thickness and its gas-mixture. An inert gas mixture ratio in the gas-gap ensures the configurations reached a targeted average salt temperature of 600oC, while avoiding salt freezing or exceeding material limits. A resistive heater placed within a thermowell and controls the temperature of the experiment (both when the reactor is on or off). The selected configurations can contain over 10 cm3 of fuel-bearing chloride salt, which is sufficient for the purposes of the post-irradiation examination (PIE) and provides sufficient volume for two submerged thermocouple probes to monitor salt temperature. The capsule wall material is Inconel 625, and weld qualifications for the assembly have been developed. A glove-box laser weld technique was refined as part of this process to ensure a leak-tight assembly for the salt-bearing assembly and reduce the risks of impurities permeating into the salt. This work was supported through the INL Laboratory Directed Research & Development (LDRD) Program under DOE Idaho Operations Office Contract DE-AC07-05ID14517.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Accurate activity determination of a californium neutron source

Accurately counting analog events requires constructing an electronics chain that produces one count for each input pulse. Here, in this work, we review the use of Nuclear Instrumentation Module electronic units for counting neutron capture events in a 3He tube. We identify two unique types of false trigger events in a leading-edge discriminator and show how a dual timer module can be used to produce a veto window to exclude these events. We use the constructed electronics chain to build an apparatus to measure neutron pulses from a 252 Cf neutron source. We compare the measurements with a Monte Carlo N-Particle (MCNP) model to determine the activity of the neutron source. Furthermore, by making additional measurements with borated polyethylene attenuators between the source and detector, we are able to determine the boron concentration of the polyethylene. This technique provides accurate determination of the source activity to a precision of 2.8% at the k=1 level. The method used is simple, inexpensive, and requires no additional calibrated instruments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2022

Recent Progress in U-10Mo Mechanical and Thermophysical Property Characterization

Results are presented on the mechanical and thermophysical property characterization of U-10Mo as part of the MP-1 qualification campaign. The thermal diffusivity, specific heat and thermal conductivity of as fabricated U-10Mo fuel foils and plates were measured using the thermal conductivity microscope (TCM), differential scanning calorimeter (DSC) and laser flash analyzer (LFA) all of which located in a shielded glove box – thermal property cell (TPC). A novel inverse method based on finite element analysis was developed to evaluate the thermal diffusivity of composite/layered materials via the LFA technique such as the 5-lyered U-10Mo monolithic fuel mini-plates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Recent Progress in U-10Mo Mechanical and Thermophysical Property Characterization -- Poster

Results are presented on the mechanical and thermophysical property characterization of U-10Mo as part of the MP-1 qualification campaign. The thermal diffusivity, specific heat and thermal conductivity of as fabricated U-10Mo fuel foils and plates were measured using the thermal conductivity microscope (TCM), differential scanning calorimeter (DSC) and laser flash analyzer (LFA) all of which located in a shielded glove box – thermal property cell (TPC). A novel inverse method based on finite element analysis was developed to evaluate the thermal diffusivity of composite/layered materials via the LFA technique such as the 5-lyered U-10Mo monolithic fuel mini-plates.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Conceptual Design of Temperature-Controlled Fueled-Salt Irradiation Experiment to Support Demonstration of Advanced Nuclear Reactors

The irradiation testing of fuel-bearing molten salts is critical to supporting the development and demonstration of molten salt reactors (MSRs). These experiments can inform several important reactor design and safety parameters, including source term modeling, evolution of thermophysical properties with burn-up, and the degradation of structural materials under reactor relevant conditions. Idaho National Laboratory is designing an instrumented and heated high temperature molten salt-fueled irradiation capsule to study the behavior of the fuel salt during in-pile irradiation. This paper details the neutronics, thermal, and mechanical analysis performed to-date. Parametric studies are performed to assess a range of material, different experiment dimensions, two in-reactor positions, and the fuel enrichment used. Principal recommendations are to opt for a peripheral reactor position to alleviate neutronic constraints, a thin salt annulus to alleviate thermal constraints, and high-temperature alloys that provide additional safety margins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

DESIGN AND PROTOYPING OF A FISSILE-BEARING CHLORIDE SALT IRRADIATION EXPERIMENT

Limited data exists on the properties of irradiated fueled chloride-based salts for use in advanced nuclear reactors. The design and prototyping of a salt irradiation experiment is underway. Mechanical design will integrate the experiment into existing assemblies in TRIGA type cores. Neutronics modeling demonstrated how targeted power densities can be reached and provide insight on radionuclide source term generation within the experiment. Thermal-hydraulic and computational fluid dynamics (CFD) analysis indicated that temperature ranges in the salt can satisfy both safety and programmatic requirements. Initial prototyping tests provided confidence in the ability to extract the salt post-irradiation, and in the heater performance. Future planned prototyping will provide an integral assessment of the proposed design prior to insertion in the reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗