Search NASA⌕ Search

Engineering topics

Tang, Wei

Publications and source records attributed to Tang, Wei.

At least 37 records · Page 2
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Microstructure Alignment Effects from Engineered Cooling during Additive Manufacturing of Alnico Magnets from Prealloyed Powder

Alnico is a rare-earth free; permanent magnet (PM) which maintains its saturation magnetization while at temperatures up to 550°C but lacks the coercivity and energy product needed for a wide range of demanding applications. With an optimal set of processing and manufacturing techniques, Alnico could replace Dy-free Nd-Fe-B magnets in certain applications if the microstructure is textured in a $\langle$001$\rangle$ direction. Additive manufacturing (AM) of near-net-shape magnets may provide such texture. To investigate the possibility, directed-energy deposition (DED) in conjunction with an actively cooled substrate was used to build samples with a compositionally modified, gas-atomized, Alnico 8 alloy. The resulting samples were solutionized and quenched, followed by magnetic annealing and a heat treatment. Magnetic properties and microstructures are compared to previous work.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comprehensive Characterization of Helium-Induced Degradation of the Friction Stir Weld on Neutron-Irradiated 304L Stainless Steel

The report describes new experimental results on the mechanical performance of the friction stir welds made on neutron-irradiated 304L stainless steel with helium. The report focuses on helium-related issues (e.g., the helium-induced degradation in the welded joint), aiming at the need to repair irradiated components of nuclear power plants. The friction stir welds analyzed here were previously produced at the US Department of Energy’s Oak Ridge National Laboratory, and initial characterization work was performed, mostly addressing the microstructure and if macroscopic cracks and helium bubbles present. The present work attempts to perform a more comprehensive study to assess mechanical performance (i.e., microhardness distribution, tensile properties, tensile deformation behaviors, and fractography analysis).

36 MATERIALS SCIENCE↗
DOE OSTI2023

Root Cause Analysis of Degradation in Protonic Ceramic Electrochemical Cell with Interfacial Electrical Sensors Using Data‐Driven Machine Learning

Abstract Protonic ceramic electrochemical cells (PCECs) offer promising paths for energy storage and conversion. Despite considerable achievements made, PCECs still face challenges such as physiochemical compatibility between componenets and suboptimal solid–solid contact at the interfaces between the electrolytes and electrodes. In this study, a novel approach is proposed that combines in situ electrochemical characterization of interfacial electrical sensor embedded PCECs and machine learning to quantify the contributions of different cell components to total degradation, as well as to predict the remaining useful life. The experimental results suggest that the overpotential induced by the oxygen electrode is 48% less than that of oxygen electrode/electrolyte interfacial contact for up to 1171 h. The data‐driven machine learning simulation predicts the RUL of up to 2132 h. The root cause of degradation is overpotential increase induced by oxygen electrode, which accounts for 82.9% of total cell degradation. The success of the failure diagnostic model is demonstrated by its consistency with degradation modes that do not manifest in electrolysis fade during early real operations. This synergistic approach provides valuable insights into practical failure diagnosis of PCECs and has the potential to revolutionize their development by enabling improved performance prediction and material selection for enhanced durability and efficiency.

25 ENERGY STORAGE↗
DOE OSTI2023

Improved Solid-State Reaction Method for Scaled-Up Synthesis of Ceramic Proton-Conducting Electrolyte Materials

Protonic ceramic electrochemical cells (PCECs) represent promising technologies in the production of clean electricity, decarbonized hydrogen, chemicals, and fuels at intermediate temperatures. One of the challenges in commercializing PCECs is to produce the electrolyte materials on a large scale. The conventional solid-state reaction (SSR) method suffers from tedious synthesis procedures and low phase purity of the products due to the formation of unwanted secondary phases. Herein, we report an improved SSR (i-SSR) method for kilogram-scale production of high phase-purity electrolyte material BaZr 0.4 Ce 0.4 Y 0.1 Yb 0.1 O 3–δ (BZCYYb4411). In this method, the ball-milled precursor powders are pelletized prior to calcination, which effectively reduces the length of the diffusion paths between the components during perovskite phase formation. In this study, the synthesis procedure and calcination temperature are carefully optimized for efficient and repeatable production based on the powder crystallization behavior. A combined technoeconomic analysis and life cycle assessment modeling suggest that the i-SSR method could reduce the total production cost and greenhouse gas emissions by up to 19% and 39%, respectively, compared to the conventional SSR method. The high quality of the synthesized electrolyte material is corroborated by the excellent electrical conductivity and electrochemical performance of the fabricated PCEC cells.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Mechanical responses of 316L stainless steel printed by wire arc additive manufacturing with different thermal histories

In this paper, 316L stainless steel walls were printed using single-bead pass and multiple-bead pass wire arc additive manufacturing (WAAM), which represent the internal basket wall and external wall of a spent nuclear fuel (SNF) canister; respectively. Scanning electron microscopy (SEM) microstructure characterization and tensile tests at room temperature (21 °C) and elevated temperature (250 °C) were performed on specimens extracted along the length and height directions of the printed walls. Results showed that grain morphology, grain angles, and retained ferrite are different between the two printed walls, which received different heat input in WAAM. The single-bead pass printed wall exhibited higher yield strength than the multiple-bead pass printed wall because of more retained ferrite and larger portion of random-high angle boundaries (RHAB) grains.

Tang, Wei↗
DOE OSTI2023

ADDITIVE MANUFACTURING AND REGULATORY TESTING OF CANISTERS FOR SPENT NUCLEAR FUEL MANAGEMENT

The back end of the fuel cycle focuses on the interim storage, transportation, and final disposition of the spent nuclear fuel from nuclear reactors. Commercial light water nuclear power stations across the United States operate with fuel assemblies being irradiated for up to 6 years (planned) in the reactor pressure vessel. After their planned irradiation, the fuel assemblies are moved to a spent fuel pool within the facility complex. After the spent nuclear fuel is removed from the fuel pool, it is typically inserted into a welded metal canister that can be transferred between overpacks for storage, transportation and possibly disposal. Most dry storage systems being used by industry today use dual purpose canisters (DPCs), designed for use in storage and transportation overpacks, but not specifically designed for disposal. Triple purpose-canisters, designed for disposal in addition to storage and transportation, have also been researched. Traditional manufacturing methods for spent fuel canisters involve fusion welding along the length or circumference of the canister which results in high tensile residual stresses in the joint weld zone (WZ) and heat affected zone (HAZ). In this paper, spent fuel canister designs were printed by wire arc additive manufacturing (AM) using the 316L SS welding wire to demonstrate: 1. Feasibility of spent nuclear fuel canister fabrication using this advanced manufacturing method, 2. Dynamic response of the additive manufacture canister design when subjected to the federally mandated Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC) physical tests for Type B packages. This paper will focus on the canister printing design and structural tests. The AM 3D printed design, regulatory testing, and post-test evaluation of the canister tested to the 10 CFR 71.71 and 10 CFR 71.73 requirements will be presented. One AM canister design was subjected to the penetration, free drop, and puncture test. Before and after the dynamic structural tests, the AM canister design was scanned with a handheld scanner to capture a 3D CAD geometry to compare to the 3D printed canister design in the deformed shape. The scanned geometry was sectioned in areas with deformation and the cross-section profile was measured to determine accurate and repeated results of the deformed shape of the AM canister design.

Martinez, Oscar↗
DOE OSTI2023

Effect of chromium on corrosion resistance of Ni-Cr-Mo-Gd alloys in seawater

Neutron absorbing materials are being considered within commercial spent nuclear fuel disposal canisters to maintain nuclear subcriticality in storage. To select candidate alloys for the canisters, both neutron absorption and corrosion resistance should be considered. This work examines corrosion resistance of Ni-Cr-Mo-Gd alloys developed specifically for neutron absorption. The addition of Gd results in a secondary gadolinide phase (Ni 5 Gd) that significantly changes the corrosion properties. Testing was performed primarily in seawater at 30°C. Seawater was selected as the most prevalent terrestrial brine and is characterized by a high chloride concentration. Various electrochemical corrosion techniques were carried out to evaluate Ni-Cr-Mo-Gd alloys with different Cr compositions and investigate the role of Ni 5 Gd phase on corrosion behavior. C22 was included as a benchmark material, due to the similarity in composition and the significant corrosion data available. Here, test results showed a tendency to passivate over time which is attributed to dissolution of surface exposed Ni 5 Gd phase. Cross-sectional analysis indicated that dissolution could penetrate hundreds of micrometers deep under aggressive conditions. It was found that higher Cr variant (21.01%) showed much shallower impact, suggesting Cr prevented primary phase corrosion and thus reduced Ni 5 Gd phase dissolution. Acid pickling of the specimens showed much less dissolution for a higher Cr material and suggested some primary phase dissolution for the low Cr specimen. Acid pickled specimens showed positive shifts in the repassivation potential, suggesting increased surface passivation.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Development of Dy-free Nd-Fe-B-based sintered magnet through grain boundary engineering using Pr-Cu alloys

For this study, Dy-free sintered magnets were fabricated by mixing Nd-Fe-B powder with various amounts of Pr-Cu powder followed by the common procedures for making Nd-Fe-B based sintered magnets. With the Pr-Cu addition increasing from 0 to 10 wt.%, the obtained magnets’ H cj increases from the original 14.5 kOe to 18.6 kOe. The highest (BH) max achieved was 35.0 MGOe with 7.5 wt.% PrCu. The distribution of the Pr and Cu elements was primarily at grain boundary and triple junctions, leading to a reduced coupling among grains, thus an enhanced H cj .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Temperature-Dependent Thermal and Mechanical Properties of a Wire Arc Additively Manufactured Low Transformation Temperature Steel

Recent research has studied the use of low transformation temperature (LTT) martensite steel as feedstock for wire arc additive manufacturing (WAAM) and low tensile residual stresses or compressive residual stresses were detected in the printed walls. These residual stress states help to improve printed product properties such as fatigue strength and corrosion resistance. However, the thermal and mechanical properties of WAAM printed LTT martensite steel walls are largely unknown. In this work, a printed LTT martensite steel was characterized for its thermal, metallurgical, and mechanical behavior at room and elevated temperatures. The temperature-dependent specific heat capacity, thermal expansion, atomic lattice spacing, and tensile properties were measured during both heating and cooling and related to observed microstructural features and computational thermodynamics predictions. These results revealed a large hysteresis in the martensitic transformation, with a martensite start temperature of 240 °C and austenite start temperature of 680 °C. Additional thermal cycles and specimen orientation did not affect the printed specimen austenite and martensite transformations. However, it was observed that the printed metal may exhibit tempering embrittlement at about 350 °C but further studies are needed to confirm that. Further, these results suggest that a temperature control of 250 °C to 350 °C during WAAM is needed to maximize the stress reduction potential of the LTT250 martensite steel. Opportunities for future implementation of LTT martensite steels and optimization of additive manufacturing process conditions are identified.

36 MATERIALS SCIENCE↗
DOE OSTI2022

316L Stainless Steel Wire Arc Additive Manufacturing and Characterization for Potential SNF Canister Production

In this paper, 316L stainless steel (316L SS) straight walls, curved walls, and vessels were printed by wire arc additive manufacturing (WAAM) using the 316L SS welding wire, to demonstrate the feasibility of spent nuclear fuel (SNF) canisters using this advanced manufacturing technique. Helium leak test with leak tight criteria of 1 × 10-7 ref-cc/s were performed on printed vessels with various wall thickness, and testing pressures were from 0.345 MPa (50 psi) to 1.724 MPa (250 psi). Printed wall microstructures were characterized using optical microscopy (OM) and scanning electron microscopy (SEM). Tensile specimens were machined out from printed walls along the length, height, and thickness directions, respectively, and tested at different temperature conditions, room temperature, 80 °C, 150 °C and 250 °C, respectively. Results showed t hat, all five WAAM-printed canisters with different thickness passed the helium leaktight criteria of radioactive materials containers by the ANSI N14.5; Dispersed micrometer-level size inclusions/voids were observed at printed wall cross sections, dendritic microstructures were found with grain size variation through the welding torch shifting direction, and very small amount of δ-ferrite and σ-phase were also observed in those cross sections; The printed walls were ductile, all tensile specimens broke with large plastic deformation/elongation and without brittle failure, and printed specimens yield strengths and tensile strengths under room temperature and 80 °C conditions are higher than minimum values of 316L SS for pressure vessels and for general applications at room temperature required by the ASTM standard, respectively.

Tang, Wei↗
DOE OSTI2022

Engineering microstructure to improve coercivity of bulk MnBi magnet

MnBi is a candidate material for high-temperature magnets because of its increasing coercivity with increasing temperatures up to 255 °C. However, most efforts in fabricating bulk MnBi magnets have run into the problem of preserving the coercivity (H cj) of its feedstock powders. About 70% of powder’s H cj would be lost during the densification process. Our micromagnetic modeling shows that the coercivity mechanism of the MnBi bulk magnet is controlled by nucleation of the reversal magnetization domains, and the large H cj loss that occurred during the powder consolidation process can be attributed to the inter-grain magnetic coupling. To attain a high H cj , the grains in the MnBi bulk magnet must be separated with a non-magnetic grain boundary phase (GBP). To validate this GBP hypothesis, we engineered MnBi bulk magnets with two different types of GBP. The first type of GBP was created in-situ by precipitating excessive Bi from the grains; the second type was created ex-situ by coating silicates on the feedstock powders before the consolidation. While both GBP work, the ex-situ approach resulted in a better H cj due to a more uniform GBP distribution. We report the H cj loss was reduced from 70% to 15%, and the (BH)max of a warm sintered bulk magnet reached 8.9 MGOe.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Friction Stir Welding – an Advanced Approach to Repair Nuclear Power Plant Components

Solid phase joining technique friction stir welding (FSW) has been shown to mitigate helium-related issues in fusion welding of irradiated steels. Here, we present detailed characterization results of the first friction stir weld of an irradiated 304L stainless steel (SS) coupon contained 5.2 atomic parts per million (appm) helium. Scanning electron microscopy (SEM) was used to characterize a cross section specimen removed from the friction stir weld. No macro helium induced crack was observed at the analyzed cross-section, and only 1 – 1.5 µm size pores were found in the stir zone (SZ) and the thermal-mechanical affected zone (TMAZ). Moreover, some minor helium aggregations (Maximum ~20 µm in length) appeared along grain boundaries inside the TMAZ. Thereafter, miniature tensile specimens were extracted from the SZ, TMAZ and heat affected zone (HAZ), and base metal (BM) and tested. All welded specimens showed high total elongations (> 60%) and strengths (> 75% BM strengths). Overall, the weld made by FSW showed much better results comparing with traditional fusion welding on irradiated SS.

Tang, Wei↗
DOE OSTI2022

Performance of stainless steel interconnects with (Mn,Co) 3 O 4 -Based coating for solid oxide electrolysis

Mixed transition-metal oxide coatings are commonly applied to stainless steel interconnects for solid oxide cell stacks. Such coatings reduce oxidation and Cr evaporation rates, leading to improved degradation rate and stack lifetime. Here, the ChromLok™ MCO-based composition (Mn,Co) 3 O 4 is applied to Crofer 22 APU stainless steel and evaluated specifically for application in solid oxide electrolyzer stacks operating around 800 °C and utilizing oxygen-ion-conducting solid oxide cells. The MCO coating is found to decrease the stainless steel oxidation rate by about one order of magnitude, and decrease the Cr evaporation rate by fourfold. Furthermore, the coating also dramatically lowers the rate of area-specific resistance increase for stainless steel coupons oxidized for 500 h with constant current applied, from 33 mΩ*cm 2 kh -1 for an uncoated coupon to less than 4 mΩ*cm2 kh -1 for coated coupons. The coating is demonstrated on full-scale interconnects for single-cells, where the coating dramatically reduces degradation rate, and for a stack, which displays stable operation for 700 h.

08 HYDROGEN↗
DOE OSTI2022

Spatiotemporal mapping of microscopic strains and defects to reveal Li-dendrite-induced failure in all-solid-state batteries

Solid-state electrolytes (SSEs) are key to the success and reliability of all-solid-state lithium batteries, potentially enabling improvements in terms of safety and energy density over state-of-the-art lithium-ion batteries. However, there are several critical challenges to their implementation, including the interfacial instability stemming from the dynamic interaction of as-formed dendritic lithium during cycling. Here, we emphasize the importance of studying the spatial distribution and temporal evolution of strains and defects in crystalline solid-state electrolytes at the micro-scale, and how this affects dendrite growth. A proof-of-principle study is demonstrated using the synchrotron radiation based micro Laue X-ray diffraction method, and a custom-developed in-situ cycling device. Defects and residual strains are mapped, and the evolution of intragranular misorientation is observed. The feasibility of using this technique is discussed, and recommendations for micro-strain engineering to address the Li/SSEs interfacial issues are given. Additionally, work directions are pointed out with the consideration of combining multi-techniques for “poly-therapy”.

36 MATERIALS SCIENCE↗
DOE OSTI2022

An Unbalanced Battle in Excellence: Revealing Effect of Ni/Co Occupancy on Water Splitting and Oxygen Reduction Reactions in Triple–Conducting Oxides for Protonic Ceramic Electrochemical Cells

Porous electrodes that conduct electrons, protons, and oxygen ions with dramatically expanded catalytic active sites can replace conventional electrodes with sluggish kinetics in protonic ceramic electrochemical cells. In this work, a strategy is utilized to promote triple conduction by facilitating proton conduction in praseodymium cobaltite perovskite through engineering non-equivalent B-site Ni/Co occupancy. Surface infrared spectroscopy is used to study the dehydration behavior, which proves the existence of protons in the perovskite lattice. The proton mobility and proton stability are investigated by hydrogen/deuterium (H/D) isotope exchange and temperature-programmed desorption. It is observed that the increased nickel replacement on the B-site has a positive impact on proton defect stability, catalytic activity, and electrochemical performance. This doping strategy is demonstrated to be a promising pathway to increase catalytic activity toward the oxygen reduction and water splitting reactions. The chosen PrNi 0.7 Co 0.3 O 3–δ oxygen electrode demonstrates excellent full-cell performance with high electrolysis current density of –1.48 A cm –2 at 1.3 V and a peak fuel-cell power density of 0.95 W cm –2 at 600 °C and also enables lower-temperature operations down to 350 °C, and superior long-term durability.

08 HYDROGEN↗
DOE OSTI2022

Electrical, thermal, and H 2 O and CO 2 poisoning behaviors of PrNi 0.5 Co 0.5 O 3-δ electrode for intermediate temperature protonic ceramic electrochemical cells

PrNi 0.5 Co 0.5 O 3-δ (PNC) exhibits adequate total electrical conductivity (~300 S/cm at 400–600 °C) and moisture has no significant effect on it. The thermal expansion coefficient of PNC is 17.6 × 10 –6 /K by dilatometry and 18.43 × 10 –6 /K by in situ XRD. PNC also demonstrates chemical stability against H 2 O and CO 2 . However, PNC symmetrical cell over proton-conducting BaZr 0.4 Ce 0.4 Y 0.1 Yb 0.1 O 3-δ (BZCYYb4411) electrolyte shows significant H 2 O and CO 2 poisoning when those are introduced into O 2 –N 2 mixture. In comparison, symmetrical cells with PNC electrode over the oxygen ion conducting Ce 0.9 Gd 0.1 O 2-δ (GDC) electrolyte show no H 2 O and CO 2 poisoning under similar conditions. Here, it is hypothesized that poisoning from H 2 O and CO 2 of the PNC proton conducting symmetrical cell is caused by their adsorption on the BZCYYb4411 electrolyte instead of PNC electrode. Such a hypothesis is supported by the H 2 O and CO 2 adsorption behaviors on PNC and BZCYYb4411 powder surfaces, as measured by temperature programmed desorption (TPD).

08 HYDROGEN↗
DOE OSTI2022

Revitalizing interface in protonic ceramic cells by acid etch

Protonic ceramic electrochemical cells hold the promise to be operated at intermediate temperatures below 600 °C. Although the high proton conductivity of the bulk electrolyte has been demonstrated, it cannot be fully utilized in electrochemical full cells due to unknown causes. A practical solution is thus urgently needed. Here we showed that it comes from poor contacts between the low-temperature processed oxygen electrode-electrolyte interface. We demonstrated that a simple acid treatment can effectively rejuvenate the high-temperature annealed electrolyte surface, resulting in reactive bonding between the oxygen electrode and the electrolyte and improved electrochemical performance and stability. This enables exceptional protonic ceramic fuel-cell performance down to 350 °C, with peak power densities of 1.6 W cm -2 at 600 °C, 650 mW cm -2 at 450 °C, and 300 mW cm -2 at 350 °C, as well as stable electrolysis operations at large current densities above 3.9 A cm -2 under 1.4 V applied voltage at 600 °C. Furthermore, our work highlights the critical role of interfacial engineering in ceramic electrochemical devices and offers new understanding and practices towards sustainable energy infrastructure.

08 HYDROGEN↗