Engineering topics
Tao, Xinyong
Publications and source records attributed to Tao, Xinyong.
Rejuvenating dead lithium supply in lithium metal anodes by iodine redox
Inactive lithium (more frequently called dead lithium) in the forms of solid-electrolyte interphase and electrically isolated metallic lithium is principally responsible for the performance decay commonly observed in lithium metal batteries. A fundamental solution of recovering dead lithium is urgently needed to stabilize lithium metal batteries. In this paper, we quantify the solid-electrolyte interphase components, and determine their relation with the formation of electrically isolated dead lithium metal. We present a lithium restoration method based on a series of iodine redox reactions mainly involving I 3 - /I - . Using a biochar capsule host for iodine, we show that the I 3 - /I - redox takes place spontaneously, effectively rejuvenating dead lithium to compensate the lithium loss. Through this design, a full-cell using a very limited lithium metal anode exhibits an excellent lifespan of 1,000 cycles with a high Coulombic efficiency of 99.9%. We also demonstrate the design with a commercial cathode in pouch cells. Cycling lithium batteries often results in inactive lithium that no longer participates in redox reactions, leading to performance deterioration. Here the authors use an iodic species to react with inactive lithium, bringing it back to life and thus making batteries last longer.
Visualizing Lithium Dendrite Formation within Solid-State Electrolytes
Solid-state electrolyte (SSE) is promising for application in allsolid-state lithium metal batteries because of its reliable safety and longevity. The failure of SSE to suppress dendrite formation of Li metal anodes has been conventionally explained by uneven Li deposition at Li/SSE interfaces and its subsequent dendritic growth. While Li deposition within SSE has been recently proposed as another key cause for SSE failure, little is known regarding the Li growth details inside the SSE itself. In this work, we performed in situ microscopic observation of Li deposition inside the SSE and obtained visualized evidence regarding the dynamic process of Li dendrite formation and growth. Here, Li is seen to directly nucleate and propagate within the SSE, leading to its structural cracking. Such behavior should be caused by the presence of P- and S-based crystalline defects in Li 3 PS 4 SSE, which is consistent with the cryo-transmission electron microscopy observations and theoretical calculations. This observation provides important insights into the growth mechanisms of Li dendrites within a working lithium battery.
Bipolar Electrodes for Next‐Generation Rechargeable Batteries
Abstract The development of advanced rechargeable batteries provides a great opportunity for basic and applied researchers to collectively overcome challenging scientific and technological barriers that directly address a critical need for energy storage. In addition to novel battery chemistries often scientifically reviewed, advanced battery structures via technological innovations that boost battery performance are also worthy of attention. In this context, bipolar electrodes (BEs) are capable of improving the specific power, simplifying cell components, and reducing manufacturing costs for rechargeable batteries. By focusing on the fundamentals and applications of BEs in rechargeable batteries, the rational utilization of BEs from an academic perspective is considered. The progress and challenges of BEs are discussed and summarized in detail. Key techniques and materials for enabling BEs are highlighted and an outlook for the future directions of BEs that involve emerging concepts, such as wearable devices, all‐solid‐state batteries, fast spraying fabrication, and recyclable secondary batteries, is also presented.
Magnetic Field-Suppressed Lithium Dendrite Growth for Stable Lithium-Metal Batteries
Lithium metal is the most attractive anode material due to its extremely high specific capacity, minimum potential, and low density. However, uncontrollable growth of lithium dendrite results in severe safety and cycling stability concerns, which hinders the application in next generation secondary batteries. In this paper, a new and facile method imposing a magnetic field to lithium metal anodes is proposed. That is, the lithium ions suffering Lorentz force due to the electromagnetic fields are put into spiral motion causing magnetohydrodynamics (MHD) effect. This MHD effect can effectively promote mass transfer and uniform distribution of lithium ions to suppress the dendrite growth as well as obtain uniform and compact lithium deposition. The results show that the lithium metal electrodes within the magnetic field exhibit excellent cycling and rate performance in a symmetrical battery. Additionally, full batteries using limited lithium metal as anodes and commercial LiFePO 4 as cathodes show improved performance within the magnetic field. In summary, a new and facile strategy of suppressing lithium dendrites using the MHD effect by imposing a magnetic field is proposed, which may be generalized to other advanced alkali metal batteries.
Direct electrochemical generation of supercooled sulfur microdroplets well below their melting temperature
Significance Since the first discovery of supercooling in 1724, the study of supercooled matter has been mainly limited to varying temperature or pressure. Here we demonstrate an electrochemical approach to generate and observe supercooled sulfur. Our methodology combines dark-field microscopy, a transparent electrochemical cell, and a fast camera to visualize the process at single microdroplet with millisecond time resolution. This platform may open up opportunities for studying supercooled liquids as the droplets approach either homogeneous nucleation to the crystalline state or enter into the glass transition. Relevant to understanding lithium-sulfur battery chemistry, liquid sulfur is observed to form in the electrochemical cell and elucidates a long-debated reaction pathway for sulfur redox reaction in this environment.
Submicron silica as high−capacity lithium storage material with superior cycling performance
Highlights: • The electrochemical performance of SiO{sub 2} is strongly associated with ball milling. • Submicron silica show superior cycling performance for lithium storage. • Mechanism of electrochemical performance of SiO{sub 2} depended on milling was discussed. - Abstract: Submicron silica (SiO{sub 2}) is prepared via directly milling bulk SiO{sub 2}, which is the major constituent of the abundant sand on the earth. The electrochemical lithium storage performance of SiO{sub 2} is found to be strongly associated with the ball milling treatment. The reversible capacity of SiO{sub 2} gradually increases from 163 to 803 mAh g{sup −1} as the milling time is extended from 0 to 72 h. For the SiO{sub 2} milled for 24 h, it exhibits excellent cycling performance with a discharge capacity of 602 mAh g{sup −1} over 150 cycles, corresponding to the capacity retention of 99.8% relative to the 2nd cycle. The different particle sizes distribution and electrochemical activity of SiO{sub 2} are responsible for the effect of ball milling on its electrochemical lithium storage performance such as reversible capacity, cycling stability, electrode polarization and initial Coulombic efficiency.
Transforming from planar to three-dimensional lithium with flowable interphase for solid lithium metal batteries
Solid-state lithium (Li) metal batteries are prominent among next-generation energy storage technologies due to their significantly high energy density and reduced safety risks. Previously, solid electrolytes have been intensively studied and several materials with high ionic conductivity have been identified. However, there are still at least three obstacles before making the Li metal foil-based solid-state systems viable, namely, high interfacial resistance at the Li/electrolyte interface, low areal capacity, and poor power output. The problems are addressed by incorporating a flowable interfacial layer and three-dimensional Li into the system. The flowable interfacial layer can accommodate the interfacial fluctuation and guarantee excellent adhesion at all time, whereas the three-dimensional Li significantly reduces the interfacial fluctuation from the whole electrode level (tens of micrometers) to local scale (submicrometer) and also decreases the effective current density for high-capacity and high-power operations. As a consequence, both symmetric and full-cell configurations can achieve greatly improved electrochemical performances in comparison to the conventional Li foil, which are among the best reported values in the literature. Noticeably, solid-state full cells paired with high–mass loading LiFePO4 exhibited, at 80°C, a satisfactory specific capacity even at a rate of 5 C (110 mA·hour g -1 ) and a capacity retention of 93.6% after 300 cycles at a current density of 3 mA cm -2 using a composite solid electrolyte middle layer. In addition, when a ceramic electrolyte middle layer was adopted, stable cycling with greatly improved capacity could even be realized at room temperature.
Sulfiphilic nickel phosphosulfide enabled Li 2 S impregnation in 3D graphene cages for Li-S batteries
A 3D graphene cage with a thin layer of electrodeposited nickel phosphosulfide for Li 2 S impregnation, using ternary nickel phosphosulphide as a highly conductive coating layer for stabilized polysulfide chemistry, is accomplished by the combination of theoretical and experimental studies. As a result, the 3D interconnected graphene cage structure leads to high capacity, good rate capability and excellent cycling stability in a Li 2 S cathode.
Catalytic oxidation of Li 2 S on the surface of metal sulfides for Li−S batteries
Significance A series of metal sulfides were systematically investigated as polar hosts to reveal the key parameters correlated to the energy barriers and polysulfide adsorption capability in Li−S batteries. The investigation demonstrates that the catalyzing oxidation capability of metal sulfides is critical in reducing the energy barrier and contributing to the remarkably improved battery performance. Density functional theory simulation allows us to identify the mechanism for how binding energy and polysulfides trapping dominate the Li 2 S decomposition process and overall battery performance. The understanding can serve as a general guiding principle for the rational design and screening of advanced materials for high-energy Li−S batteries.
Balancing surface adsorption and diffusion of lithium-polysulfides on nonconductive oxides for lithium–sulfur battery design
Lithium–sulfur batteries have attracted attention due to their six-fold specific energy compared with conventional lithium-ion batteries. Dissolution of lithium polysulfides, volume expansion of sulfur and uncontrollable deposition of lithium sulfide are three of the main challenges for this technology. State-of-the-art sulfur cathodes based on metal-oxide nanostructures can suppress the shuttle-effect and enable controlled lithium sulfide deposition. However, a clear mechanistic understanding and corresponding selection criteria for the oxides are still lacking. Herein, various nonconductive metal-oxide nanoparticle-decorated carbon flakes are synthesized via a facile biotemplating method. The cathodes based on magnesium oxide, cerium oxide and lanthanum oxide show enhanced cycling performance. Adsorption experiments and theoretical calculations reveal that polysulfide capture by the oxides is via monolayered chemisorption. Moreover, we show that better surface diffusion leads to higher deposition efficiency of sulfide species on electrodes. Lastly, oxide selection is proposed to balance optimization between sulfide-adsorption and diffusion on the oxides.
Ultrafast and Highly Reversible Sodium Storage in Zinc-Antimony Intermetallic Nanomaterials
The progress on sodium-ion battery technology faces many grand challenges, one of which is the considerably lower rate of sodium insertion/deinsertion in electrode materials due to the larger size of sodium (Na) ions and complicated redox reactions compared to the lithium-ion systems. Here, it is demonstrated that sodium ions can be reversibly stored in Zn-Sb intermetallic nanowires at speeds that can exceed 295 nm s -1 . Remarkably, these values are one to three orders of magnitude higher than the sodiation rate of other nanowires electrochemically tested with in situ transmission electron microscopy. It is found that the nanowires display about 161% volume expansion after the first sodiation and then cycle with an 83% reversible volume expansion. Despite their massive expansion, the nanowires can be cycled without any cracking or facture during the ultrafast sodiation/desodiation process. Additionally, most of the phases involved in the sodiation/desodiation process possess high electrical conductivity. More specifically, the NaZnSb exhibits a layered structure, which provides channels for fast Na + diffusion. This observation indicates that Zn-Sb intermetallic nanomaterials offer great promise as high rate and good cycling stability anodic materials for the next generation of sodium-ion batteries.
Magnetic Field-Controlled Lithium Polysulfide Semiliquid Battery with Ferrofluidic Properties
Explore the source record for details and available documents.
Highly Nitridated Graphene-Li 2 S Cathodes with Stable Modulated Cycles
Explore the source record for details and available documents.