Engineering topics

Tatom, J. W.

Publications and source records attributed to Tatom, J. W..

5 records

NASA NTRS1972

An analytical investigation of the impingement of jets on curved deflectors.

Numerical solutions are obtained for the cases of straight circular jets impinging on axisymmetric curved surfaces, and plane jets impinging symmetrically on two-dimensional curved surfaces. These geometries are representative of some types of thrust reversers for transport aircraft. The solutions are based on the assumptions of incompressible and potential flow. The velocity field, pressure distribution at the deflector surface, and reverser effectiveness are predicted for deflector turning angles of 15 to 75 deg, deflector width to jet diameter ratios of 1.5-2.0, and ratios of deflector clearance to jet diameter of 1.0-3.0. Reverser effectiveness is found to be a maximum for a ratio of deflector clearance to jet diameter of about 2.0. The effect of back pressuring resulting from the presence of the deflector is predicted.

Schnurr, N. M.↗

NASA NTRS1972

A method for increasing thrust reverser utilization on STOL aircraft.

A technique for increasing the utilization of thrust reversers on STOL aircraft is described. The technique involves asymmetric orientation of the reversed exhaust in such a manner as to avoid the problems of self-ingestion, even in the presence of a cross wind, and cross ingestion between adjacent engines. Experimental results of ingestion in a single nacelle inlet are discussed and flow visualization pictures are presented. An analytical model of ingestion is described and sample results are shown.

Tatom, J. W.↗

NASA NTRS1972

Temperature and velocity field of the two-dimensional transverse hot-air jet in a freestream flow.

Experimental investigation of the low subsonic, two-dimensional transverse hot-air jet. In the study jet-to-freestream angles of 90, 120, 135, and 150 deg and jet-to-freestream velocity ratios of 5, 10, and 20 were investigated. In the tests the jet velocity and temperature fields were measured using a temperature-compensated hot-wire anemometer. Photographs of the flowfield were also made. The tests results are compared with the available data and analysis. Results indicate a relatively minor deflection of the freestream by the jet and the presence of a large separated flow region behind the jet.

Tatom, J. W.↗

NASA NTRS1972

A study of jet impingement on curved surfaces followed by oblique introduction into a freestream flow

An experimental investigation of the temperature and velocity fields generated by a two-dimensional transverse jet was conducted. An approximate analysis of a deflected radial plane jet was developed. An analytical model of aircraft ingestion was extended to include computation of the inlet flow field. An investigation of the use of flaps as thrust reversers was initiated. Analyses of the impingement of a round incompressible and a round compressible jet on a arbitrary axisymmetric surface were completed. A computer study of the effects on performance of thrust reverser geometry was completed and the results compared with existing data. An experimental investigation of three-dimensional jet impingement on nonplane surfaces was also initiated.

Tatom, J. W.↗

NASA NTRS1972

An analytical investigation of the impingement jets on curved deflectors

Numerical solutions are obtained for the cases of straight circular jets impinging on axisymmetric curved surfaces and plane jets impinging symmetrically on two-dimensional curved surfaces. These geometries are representative of some types of thrust reversers for transport aircraft. The solutions are based on the assumptions of incompressible and potential flow. The velocity field, pressure distribution at the deflector surface and reverser effectiveness are predicted for deflector turning angles of 15 to 75 deg, deflector width to jet diameter ratios of 1.5 to 2.0, and ratios of deflector clearance to jet diameter of 1.0 to 3.0. Reverser effectiveness is found to be a maximum for a ratio of deflector clearance to jet diameter of about 2.0. The effect of back pressuring due to the presence of the deflector is predicted. Experimental verification of the theoretical predictions is obtained. A compressible solution obtained for a limited number of cases indicates that the incompressible solution is satisfactory for jet exit Mach numbers less than 0.8.

Schnurr, N. M.↗