Engineering topics

Taylor, D. S.

Publications and source records attributed to Taylor, D. S..

7 records

NASA NTRS1978

Simultaneous velocity and particle size measurement in two phase flows by Laser Anemometry

A technique for particle size measurement by using Laser Doppler Anemometry is discussed. An additional gate photomultiplier has been introduced at right angles to the optical axis in order to select only those particles passing through the central region of the measurement control volume. Particle sizing measurements have been made in sprays of glass particles using the modified Laser Anemometry system. Measurements in fuel sprays are also reported and compared with the results obtained by a photographic technique. The application of the particle sizing technique to opaque particles is investigated and suitable optical arrangements are suggested. Light scattering characteristics of Laser Anemometry systems for different optical geometries are calculated to select the optimum optical arrangement for the particle sizing measurements.

Ungut, A.↗

NASA NTRS1974

Unpowered to powered failure rate ratio - A key reliability parameter

It is shown that the initial assumption of the ratio of unpowered to powered failure rates can have a strong influence on the design of a modular system intended for space missions. The analysis is performed for parallel systems and for triple modular redundant systems. Parallel systems are shown to be much more sensitive to the unpowered to powered failure rate ratio than the TMR/Spares systems, however, regardless of which standby redundancy technique is considered, the dependence of the system reliability on this ratio increases as the number of standby spares increases.

Taylor, D. S.↗

NASA NTRS1973

A reliability and comparative analysis of two standby system configurations.

Equations are derived which enable one to calculate the system reliability for parallel or triple modular redundant systems with standby spares. Software error detection is introduced into the TMR/Spares system configuration in order to utilize fully all of the units. An indication of the sensitivity of the system reliability to an increase in the number of spares, partitioning, switching, variations in the powered and unpowered failures rates, and time is presented. A comparison of the parallel and the TMR/Spares system configurations, under similar conditions, is given.

Taylor, D. S.↗

NASA NTRS1973

Optimum spaceborne computer system design by simulation

A deterministic simulator is described which models the Automatically Reconfigurable Modular Multiprocessor System (ARMMS), a candidate computer system for future manned and unmanned space missions. Its use as a tool to study and determine the minimum computer system configuration necessary to satisfy the on-board computational requirements of a typical mission is presented. The paper describes how the computer system configuration is determined in order to satisfy the data processing demand of the various shuttle booster subsytems. The configuration which is developed as a result of studies with the simulator is optimal with respect to the efficient use of computer system resources.

Williams, T.↗

NASA NTRS1972

Memory interface simulator: A computer design aid

Results are presented of a study conducted with a digital simulation model being used in the design of the Automatically Reconfigurable Modular Multiprocessor System (ARMMS), a candidate computer system for future manned and unmanned space missions. The model simulates the activity involved as instructions are fetched from random access memory for execution in one of the system central processing units. A series of model runs measured instruction execution time under various assumptions pertaining to the CPU's and the interface between the CPU's and RAM. Design tradeoffs are presented in the following areas: Bus widths, CPU microprogram read only memory cycle time, multiple instruction fetch, and instruction mix.

Taylor, D. S.↗

NASA NTRS1972

Optimum spaceborne computer system design by simulation

A deterministic digital simulation model is described which models the Automatically Reconfigurable Modular Multiprocessor System (ARMMS), a candidate computer system for future manned and unmanned space missions. Use of the model as a tool in configuring a minimum computer system for a typical mission is demonstrated. The configuration which is developed as a result of studies with the simulator is optimal with respect to the efficient use of computer system resources, i.e., the configuration derived is a minimal one. Other considerations such as increased reliability through the use of standby spares would be taken into account in the definition of a practical system for a given mission.

Williams, T.↗

NASA NTRS1971

A system reliability analysis for stand-by spares with non-zero unpowered failure rates

Equations which define the reliability of n-fold parallel systems with stand-by spares, and triply redundant, majority-voting systems with stand-by spares have been derived. The stand-by spares have been assumed to have a non-zero failure rate while in the stand-by mode. A Monte Carlo system simulation has been generated and the results compared to the theoretical reliability predictions. A comparison of these two stand-by configurations is also presented for three through six total units.

Taylor, D. S.↗