Engineering topics

Taylor, John G.

Publications and source records attributed to Taylor, John G..

7 records

NASA NTRS1996

Static Internal Performance of a Two-Dimensional Convergent-Divergent Nozzle with External Shelf

An investigation was conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance of a two-dimensional convergent-divergent nozzle. The nozzle design was tested with dry and afterburning throat areas, which represent different power settings and three expansion ratios. For each of these configurations, three trailing-edge geometries were tested. The baseline geometry had a straight trailing edge. Two different shaping techniques were applied to the baseline nozzle design to reduce radar observables: the scarfed design and the sawtooth design. A flat plate extended downstream of the lower divergent flap trailing edge parallel to the model centerline to form a shelf-like expansion surface. This shelf was designed to shield the plume from ground observation (infrared radiation (IR) signature suppression). The shelf represents the part of the aircraft structure that might be present in an installed configuration. These configurations were tested at nozzle pressure ratios from 2.0 to 12.0.

Lamb, Milton↗

NASA NTRS1993

Internal performance of Highly Integrated Deployable Exhaust Nozzles

The internal performance characteristics of Highly Integrated Deployable Exhaust Nozzles (HIDEN) applicable to advanced short take-off and vertical landing aircraft have been investigated. Four nozzle concepts, designed for fan and core flow installations, were tested with varying contraction ratio and nozzle exit plane shape. In addition, two offtake duct designs, along with several centerbody and blocker geometries were tested to evaluate their effect on the static thrust and flow performance. This investigation was conducted in the static test facility of the NASA Langley 16-Foot Transonic Tunnel. A six-component strain-gage balance collected force and moment data, and static pressure, total pressure, and total temperature measurements were also made internal to the model. Room temperature, dry high-pressure air was used to simulate jet exhaust. The results indicate that the internal performance of these HIDEN concepts is comparable to previously tested nozzle concepts designed for thrust vectoring about a bearing plane. This report presents the configuration design of the HIDEN concepts and the results of the internal performance testing.

Taylor, John G.↗

NASA NTRS1992

Supersonic investigation of two dimensional hypersonic exhaust nozzles

An experimental investigation was conducted in the NASA Lewis 10 x 10 ft supersonic Wind Tunnel to determine the performance characteristics of 2D hypersonic exhaust nozzles/afterbodies at low supersonic conditions. Generally, this type of application requires a single expansion ramp nozzle (SERN) that is highly integrated with the airframe of the hypersonic vehicle. At design conditions (hypersonic speeds), the nozzle generally exhibits acceptable performance. At off-design conditions (transonic to mid-supersonic speeds), nozzle performance of a fixed geometry configuration is generally poor. Various 2-D nozzle configurations were tested at off-design conditions from Mach 2.0 to 3.5. Performance data is presented at nozzle pressure ratios from 1 to 35. Jet exhaust was simulated with high-pressure air. To study performance of different geometries, nozzle configurations were varied by interchanging the following model parts: internal upstream contour, expansion ramp, sidewalls, and cowl.

Carboni, Jeanne D.↗

NASA NTRS1991

Internal performance of a hybrid axisymmetric/nonaxisymmetric convergent-divergent nozzle

An investigation was conducted in the static test facility of the Langley 16-foot transonic tunnel to determine the internal performance of a hybrid axisymmetric/nonaxisymmetric nozzle in forward-thrust mode. Nozzle cross-sections in the spherical convergent section were axisymmetric whereas cross-sections in the divergent flap area nonaxisymmetric (two-dimensional). Nozzle concepts simulating dry and afterburning power settings were investigated. Both subsonic cruise and supersonic cruise expansion ratios were tested for the dry power nozzle concepts. Afterburning power configurations were tested at an expansion ratio typical for subsonic acceleration. The spherical convergent flaps were designed in such a way that the transition from axisymmetric to nonaxisymmetric cross-section occurred in the region of the nozzle throat. Three different nozzle throat geometries were tested for each nozzle power setting. High-pressure air was used to simulate jet exhaust at nozzle pressure ratios up to 12.0.

Taylor, John G.↗

NASA NTRS1990

Static investigation of a two-dimensional convergent-divergent exhaust nozzle with multiaxis thrust-vectoring capability

An investigation was conducted in the Static Test Facility of the NASA Langley 16-Foot Transonic Tunnel to determine the internal performance of two-dimensional convergent-divergent nozzles designed to have simultaneous pitch and yaw thrust vectoring capability. This concept utilized divergent flap rotation of thrust vectoring in the pitch plane and deflection of flat yaw flaps hinged at the end of the sidewalls for yaw thrust vectoring. The hinge location of the yaw flaps was varied at four positions from the nozzle exit plane to the throat plane. The yaw flaps were designed to contain the flow laterally independent of power setting. In order to eliminate any physical interference between the yaw flap deflected into the exhaust stream and the divergent flaps, the downstream corners of both upper and lower divergent flaps were cut off to allow for up to 30 deg of yaw flap deflection. The impact of varying the nozzle pitch vector angle, throat area, yaw flap hinge location, yaw flap length, and yaw flap deflection angle on nozzle internal performance characteristics, was studied. High-pressure air was used to simulate jet exhaust at nozzle pressure ratios up to 7.0. Static results indicate that configurations with the yaw flap hinge located upstream of the exit plane provide relatively high levels of thrust vectoring efficiency without causing large losses in resultant thrust ratio. Therefore, these configurations represent a viable concept for providing simultaneous pitch and yaw thrust vectoring.

Taylor, John G.↗

NASA NTRS1990

Internal performance of two nozzles utilizing gimbal concepts for thrust vectoring

The internal performance of an axisymmetric convergent-divergent nozzle and a nonaxisymmetric convergent-divergent nozzle, both of which utilized a gimbal type mechanism for thrust vectoring was evaluated in the Static Test Facility of the Langley 16-Foot Transonic Tunnel. The nonaxisymmetric nozzle used the gimbal concept for yaw thrust vectoring only; pitch thrust vectoring was accomplished by simultaneous deflection of the upper and lower divergent flaps. The model geometric parameters investigated were pitch vector angle for the axisymmetric nozzle and pitch vector angle, yaw vector angle, nozzle throat aspect ratio, and nozzle expansion ratio for the nonaxisymmetric nozzle. All tests were conducted with no external flow, and nozzle pressure ratio was varied from 2.0 to approximately 12.0.

Berrier, Bobby L.↗

NASA NTRS1988

A static investigation of a simultaneous pitch and yaw thrust vectoring 2-D C-D nozzle

An investigation has been conducted in the static test facility of the Langley 16-Foot Transonic Tunnel to determine the internal performance and flow-turning capability of a two-dimensional convergent-divergent nozzle. Thrust vectoring in the pitch plane was provided by rotation of the divergent flaps. The exhaust stream was turned in the yaw direction by deflection of yaw flaps hinged at the end of the nozzle sidewalls. The yaw flap hinge location was varied along the divergent region of the nozzle at four locations including the exit plane and the throat plane. The three hinge locations upstream of the nozzle exit plane required the downstream corners of both upper and lower divergent flaps to be cut off to eliminate interference when the yaw flaps were deflected. Three different lengths of yaw flaps were tested at several angles of deflection. The nozzle simulated a dry power setting with an expansion ratio typical of subsonic cruise and was tested at nozzle pressure ratios from 2.0 to 7.0.

Taylor, John G.↗