Search NASA⌕ Search

Engineering topics

Taylor, Robert A.

Publications and source records attributed to Taylor, Robert A..

Solar Energy Integration in Buildings

Energy consumption in buildings has been steadily increasing and contributing up to 40% of the total energy use in developed countries [1]. In developing countries, the share of building energy consumption is smaller, but given population growth, urbanization, and rising demands for building services and comfort, the sharp rise of building energy use is probably inevitable. Thus, reducing building energy consumption plays a very important role in controlling global energy demand and mitigating climate change, so as to develop a sustainable environment. Solar energy, as the most important source of renewable energy, features the characteristics of clean, renewable, inexhaustible, and widely distributed energy, relative to other kinds of energy sources. Solar energy systems can now generate electricity at a cost equal to or lower than local grid-supplied electricity [2]. More importantly, solar energy can provide almost all forms of energy needed by buildings, through active or passive methods.

buildings↗

Distributed Energy Systems: Security Implications of the Grid of the Future

Distributed Energy Resources (DER) are being added to the nation's electric grid, and as penetration of these resources increases, they have the potential to displace or offset large-scale, capital-intensive, centralized generation. Integration of DER into operation of the traditional electric grid requires automated operational control and communication of DER elements, from system measurement to control hardware and software, in conjunction with a utility's existing automated and human-directed control of other portions of the system. Implementation of DER technologies suggests a number of gaps from both a security and a policy perspective.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Non-polar InGaN quantum dot emission with crystal-axis oriented linear polarization

Polarization sensitive photoluminescence is performed on single non-polar InGaN quantum dots. The studied InGaN quantum dots are found to have linearly polarized emission with a common polarization direction defined by the [0001] crystal axis. Around half of ∼40 studied dots have a polarization degree of 1. For those lines with a polarization degree less than 1, we can resolve fine structure splittings between −800 μeV and +800 μeV, with no clear correlation between fine structure splitting and emission energy.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Observations of Rabi oscillations in a non-polar InGaN quantum dot

Experimental observation of Rabi rotations between an exciton excited state and the crystal ground state in a single non-polar InGaN quantum dot is presented. The exciton excited state energy is determined by photoluminescence excitation spectroscopy using two-photon excitation from a pulsed laser. The population of the exciton excited state is seen to undergo power dependent damped Rabi oscillations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Experimental investigation of the latent heat of vaporization in aqueous nanofluids

This paper reports an experimental investigation of the latent heat of vaporization (h{sub fg}) in nanofluids. Two different types of nanoparticles, graphite and silver, suspended in deionized water were exposed to a continuous laser beam (130 mW, 532 nm) to generate boiling. The latent heat of vaporization in the nanofluids was determined by the measured vapor mass generation and the heat input. To ensure that the measured h{sub fg} values are independent of heating method, the experiments were repeated with an electrically heated hot wire as a primary heat input. These experiments show considerable variation in the h{sub fg} of nanofluids. That is, graphite nanofluid exhibits an increased h{sub fg} and silver nanofluid shows a decrease in h{sub fg} compared to the value for pure water. As such, these results indicate that relatively low mass fractions of nanoparticles can apparently create large changes in h{sub fg}.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Pressure Distributions at Transonic Speeds for Bumpy and Indented Midsections of a Basic Parabolic-Arc Body

The measured static-pressure distributions at the model surface and in the surrounding flow field are presented for a basic parabolic-arc body having a fineness ratio of 14 and for three additional bodies obtained by modifying the basic parabolic-arc body along the middle portion of the body length by adding a bump, by indenting, or by quadripole shaping. The data were obtained with the various bodies at zero angle of attack. The Mach number varied from 0.80 to 1.20 with a corresponding Reynolds number (based on body length) variation of 27 x 10(exp 6) to 38 x 10(exp 6). The data are subject to tunnel-wall interference and do not represent free-air conditions.

Taylor, Robert A.↗