Engineering topics
Publications and source records attributed to Taylor, Robert P..
This report documents the research conducted to update computer models for dynamic fluid flow simulation of the E-1 test stand subsystems at te NASA John C. Stennis Space Center.Work also involved significant upgrades to the capabilities of EASY/ROCKETS library through the inclusion of the NIST-12 thermodynamic property database and development of new control system modules.
The objective of this research was to experimentally investigate the combined effects of freestream acceleration and surface roughness on heat transfer and fluid flow in the turbulent boundary layer. The experiments included a variety of flow conditions ranging from aerodynamically smooth to transitionally rough to fully rough boundary layers with accelerations ranging from moderate to moderately strong. The test surfaces used were a smooth-wall test surface and two rough-wall surfaces which were roughened with 1.27 mm diameter hemispheres spaced 2 and 4 base diameters apart in a staggered array. The measurements consisted of Stanton number distributions, mean temperature profiles, skin friction distributions, mean velocity profiles, turbulence intensity profiles, and Reynolds stress profiles. The Stanton numbers for the rough-wall experiments increased with acceleration. For aerodynamically smooth and transitionally rough boundary layers, the effect of roughness is not seen immediately at the beginning of the accelerated region as it is for fully rough boundary layers; however, as the boundery layer thins under acceleration, the surface becomes relatively rougher resulting in a sharp increase in Stanton number.
The view factors which are used in diffuse-gray radiation enclosure calculations are often computed by approximate numerical integrations. These approximately calculated view factors will usually not satisfy the important physical constraints of reciprocity and closure. In this paper several view-factor rectification algorithms are reviewed and a rectification algorithm based on a least-squares numerical filtering scheme is proposed with both weighted and unweighted classes. A Monte-Carlo investigation is undertaken to study the propagation of view-factor and surface-area uncertainties into the heat transfer results of the diffuse-gray enclosure calculations. It is found that the weighted least-squares algorithm is vastly superior to the other rectification schemes for the reduction of the heat-flux sensitivities to view-factor uncertainties. In a sample problem, which has proven to be very sensitive to uncertainties in view factor, the heat transfer calculations with weighted least-squares rectified view factors are very good with an original view-factor matrix computed to only one-digit accuracy. All of the algorithms had roughly equivalent effects on the reduction in sensitivity to area uncertainty in this case study.
An uncertainty analysis of diffuse-gray enclosure problems is presented. The genesis was a diffuse-gray enclosure problem which proved to be hypersensitive to the specification of view factors. This genesis is discussed in some detail. The uncertainty analysis is presented for the general diffuse-gray enclosure problem and applied to the hypersensitive case study. It was found that the hypersensitivity could be greatly reduced by enforcing both closure and reciprocity for the view factors. The effects of uncertainties in the surface emissivities and temperatures are also investigated.
A report on the progress of porting the ROCETS (ROCket Engine Transient Simulator) into the EASY5x simulation environment is presented. Brief descriptions of each of the software systems, information regarding the actual port process, and examples comparing the results of the two systems are given. It is shown that EASY5x is a suitable environment for utilization of the ROCETS engineering modules, and that, for the example systems shown, EASY5x actually seems to give more accurate solutions than the straight ROCETS code.
The work reported here was motivated by concern over the use of smooth heat flux gages for heat transfer measurements on the otherwise rough turbine blades. Stanton number distributions and boundary layer profiles of mean temperature, mean velocity, and turbulence intensity are reported for a surface with a step change from a rough to a smooth surface. In most cases, the Stanton number immediately downstream of the change in roughness drops below the all-smooth-wall data at the same x-Reynolds number. The alignment of the smooth surface between the bases and crests of the roughness elements is shown to have only a weak effect on the Stanton number distribution. It is concluded that the use of smooth heat flux gages on otherwise rough surfaces can cause large errors. It is recommended that heat transfer data collected in this manner be used with caution.
The use is studied of smooth heat flux gages on the otherwise very rough SSME fuel pump turbine blades. To gain insights into behavior of such installations, fluid mechanics and heat transfer data were collected and are reported for a turbulent boundary layer over a surface with a step change from a rough surface to a smooth surface. The first 0.9 m length of the flat plate test surface was roughened with 1.27 mm hemispheres in a staggered, uniform array spaced 2 base diameters apart. The remaining 1.5 m length was smooth. The effect of the alignment of the smooth surface with respect to the rough surface was also studied by conducting experiments with the smooth surface aligned with the bases or alternatively with the crests of the roughness elements. Stanton number distributions, skin friction distributions, and boundary layer profiles of temperature and velocity are reported and are compared to previous data for both all rough and all smooth wall cases. The experiments show that the step change from rough to smooth has a dramatic effect on the convective heat transfer. It is concluded that use of smooth heat flux gages on otherwise rough surfaces could cause large errors.
Measurements of Stanton numbers, velocity profiles, temperature profiles, and turbulence intensity profiles are reported for turbulent flat plate boundary layer flows with a step change in surface roughness. The first 0.9 m length of the test surface is roughened with 1.27 mm diameter hemispheres spaced 2 base diameters apart in a staggered array. The remaining 1.5 m length is smooth. The experiments show that the step change from a rough to a smooth surface has a dramatic effect on the convective heat transfer. In many cases, the Stanton number drops below the smooth-wall correlation immediately downstream of the change in roughness. The Stanton number measurements are compared with predictions using the discrete element method with excellent results.