Search NASA⌕ Search

Engineering topics

Tedder, Sarah

Publications and source records attributed to Tedder, Sarah.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Bit Error Rate Performance of a Free Space Optical Link Using Double Clad Fibers

Mobile and embedded applications are emerging in the growing field of free space optical links (FSOL). Some mobile applications for FSOL include spacecraft, aircraft, and automotive. These applications by nature require low size weight and power (SWaP) solutions. The main challenge with any FSOL system is the strict pointing requirements. Common solutions to pointing and alignment of FSOL include gimbals, fast steering mirrors, and adaptive optics. All of which provide viable solutions at the cost of increased SWaP. Previously, we presented the use of both large core fibers and double clad fibers (DCF) to interface FSOL transmit and receive optics with small form factor pluggable optical transceivers (SFP). Double clad fibers have been shown to enable a common optical path by transmitting through a single mode core and receiving through a large inner cladding. This enables a single set of symmetric transmit and receive optics, which decreases the SWaP. In addition, using DCF increases the received power stability of the link relative to a multi-mode fiber (MMF) transmitting. To determine the viability of the system, bit error rate performance needs to be investigated. The results of this paper show that at a bit rate of 10 Gbps, double clad fibers offer similar bit error rate performance to single mode fibers when transmitting and multi-mode fibers when receiving enabling a symmetric duplex FSOL reducing SWaP.

Double Clad Fiber↗
NASA NTRS2018

Exploration of Double Clad Fibers for Increased Stability of Bidirectional Free Space Optical Links

Bidirectional, high data rate, low size, weight, and power (SWaP), and low cost free space optical links are needed for space communication applications to send and receive large volumes of data. We are exploring design strategies for optical transceivers to reduce SWaP and cost through increased misalignment tolerance (pointing requirement reduction) and sharing the optical transmit and receive paths (imposing optical symmetry). In applications where the detector is fiber coupled, the fiber numerical aperture is the main driver of the pointing accuracy requirement. Unfortunately, reducing the pointing requirement by increasing the fiber numerical aperture symmetrically causes instability in received power over small environmental changes. This paper explores double clad fibers as a solution to both reduce the power instability and increase the pointing accuracy tolerance. Double clad fibers can transmit a Gaussian beam from a single mode fiber and receive in a multi-mode aperture. Results show that double clad fiber have an improved misalignment tolerance and a higher stability for small changes in temperature when compared to single mode fibers and multimode fibers. Also, double clad fibers are shown to match the performance of an asymmetrical link design with a single mode transmit fiber and a multimode receive fiber.

Double Clad fibers↗
NASA NTRS2018

Bit Error Rate Performance on Passive Alignment in Free Space Optical Links Using Large Core Fibers

A 20-meter free-space optical link (FSOL) is proposed for data transmission between external ISS payload sites and the main cabin at a target rate of 10 Gbps (gigabits per second). Motion between a payload site and the main cabin is predicted to cause up to 5 cm in lateral misalignment and 0.2 degrees of angular misalignment. Due to the harsh environment of space it is advantageous to locate the optical transceivers inside the spacecraft or in a controlled environment. With the optical components and transceivers in separate locations, a fiber optic cable will be required to carry light between the two. In our past work we found that the use of large-core fibers provide an increased misalignment tolerance for such systems and could eliminate the need for active control of the optics. In that work, it was shown that a 105 m core diameter fiber optic cable offered a viable low SWaP (size, weight, and power) solution for the ISS application; however, the effects of modal dispersion were not investigated. This paper will present bit error rate performance of the FSOL using these large-core fibers.

Free Space Optical Link↗
NASA NTRS2018

Bit Error Rate Performance on Passive Alignment in Free Space Optical Links Using Large Core Fibers

A 20-meter free-space optical link (FSOL) is proposed for data transmission between external ISS payload sites and the main cabin at a target rate of 10 Gbps (gigabits per second). Motion between a payload site and the main cabin is predicted to cause up to 5 cm in lateral misalignment and 0.2 degrees of angular misalignment. Due to the harsh environment of space it is advantageous to locate the optical transceivers inside the spacecraft or in a controlled environment. With the optical components and transceivers in separate locations, a fiber optic cable will be required to carry light between the two. In our past work we found that the use of large-core fibers provide an increased misalignment tolerance for such systems and could eliminate the need for active control of the optics. In that work, it was shown that a 105 m core diameter fiber optic cable offered a viable low SWaP (size, weight, and power) solution for the ISS application; however, the effects of modal dispersion were not investigated. This paper will present bit error rate performance of the FSOL using these large-core fibers.

Optical Bit Error Rate Testing↗
NASA NTRS2016

Study of Lateral Misalignment Tolerance of a Symmetric Free-Space Optical Link for Intra International Space Station Communication

This paper describes the study of lateral misalignment tolerance of a symmetric high-rate free-space optical link (FSOL) for use between International Space Station (ISS) payload sites and the main cabin. The link will enable gigabit per second (Gbps) transmission of data, which is up to three orders of magnitude greater than the current capabilities. This application includes 10-20 meter links and requires minimum size, weight, and power (SWaP). The optical power must not present an eye hazard and must be easily integrated into the existing ISS infrastructure. On the ISS, rapid thermal changes and astronaut movement will cause flexure of the structure which will potentially misalign the free space transmit and receive optics 9 cm laterally and 0.2 degrees angularly. If this misalignment is not accounted for, a loss of the link or degradation of link performance will occur. Power measurements were collected to better understand the effect of various system design parameters on lateral misalignment. Parameters that were varied include: the type of small form pluggable (SFP) transceivers, type of fiber, and transmitted power level. A potential solution was identified that can reach the lateral misalignment tolerance (decenter span) required to create an FSOL on the ISS by using 105 m core fibers, a duplex SFP, two channels of light, and two fiber amplifiers.

optical communications↗
NASA NTRS2016

Alternative Bio-Derived JP-8 Class Fuel and JP-8 Fuel: Flame Tube Combustor Test Results Compared using a GE TAPS Injector Configuration

This paper presents results from tests in a NASA Glenn Research Center (GRC) flame tube facility, where a bio-derived alternate fuel was compared with JP-8 for emissions and general combustion performance. A research version of General Electric Aviation (GE) TAPS injector was used for the tests. Results include 2D, planar laser-based imaging as well as basic flow visualization of the flame. Four conditions were selected that simulate various engine power conditions relevant to NASA Fundamental Aeronautics Supersonics and Environmentally Responsible Aviation Projects were tested.

optical diagnostics↗
NASA NTRS2012

OH Planar Laser Induced Fluorescence (PLIF) Measurements for the Study of High Pressure Flames: An Evaluation of a New Laser and a New Camera System

Planar laser induced fluorescence (PLIF) is used by the Combustion Branch at the NASA Glenn Research Center (NASA Glenn) to assess the characteristics of the flowfield produced by aircraft fuel injectors. To improve and expand the capabilities of the PLIF system new equipment was installed. The new capabilities of the modified PLIF system are assessed by collecting OH PLIF in a methane/air flame produced by a flat flame burner. Specifically, the modifications characterized are the addition of an injection seeder to a Nd:YAG laser pumping an optical parametric oscillator (OPO) and the use of a new camera with an interline CCD. OH fluorescence results using the injection seeded OPO laser are compared to results using a Nd:YAG pumped dye laser with ultraviolet extender (UVX). Best settings of the new camera for maximum detection of PLIF signal are reported for the controller gain and microchannel plate (MCP) bracket pulsing. Results are also reported from tests of the Dual Image Feature (DIF) mode of the new camera which allows image pairs to be acquired in rapid succession. This allows acquisition of a PLIF image and a background signal almost simultaneously. Saturation effects in the new camera were also investigated and are reported.

Tedder, Sarah↗
NASA NTRS2007

Development of Supersonic Combustion Experiments for CFD Modeling

This paper describes the development of an experiment to acquire data for developing and validating computational fluid dynamics (CFD) models for turbulence in supersonic combusting flows. The intent is that the flow field would be simple yet relevant to flows within hypersonic air-breathing engine combustors undergoing testing in vitiated-air ground-testing facilities. Specifically, it describes development of laboratory-scale hardware to produce a supersonic combusting coaxial jet, discusses design calculations, operability and types of flames observed. These flames are studied using the dual-pump coherent anti- Stokes Raman spectroscopy (CARS) - interferometric Rayleigh scattering (IRS) technique. This technique simultaneously and instantaneously measures temperature, composition, and velocity in the flow, from which many of the important turbulence statistics can be found. Some preliminary CARS data are presented.

Baurle, Robert↗
NASA NTRS2006

Simultaneous CARS and Interferometric Rayleigh Scattering

This paper reports for the first time the combination of a dual-pump coherent anti-Stokes Raman scattering system with an interferometric Rayleigh scattering system (CARS - IRS) to provide time-resolved simultaneous measurement of multiple properties in combustion flows. The system uses spectrally narrow green (seeded Nd:YAG at 532 nm) and yellow (552.9 nm) pump beams and a spectrally-broad red (607 nm) beam as the Stokes beam. A spectrometer and a planar Fabry-Perot interferometer used in the imaging mode are used to record the spectrally broad CARS spectra and the spontaneous Rayleigh scattering spectra, respectively. Time-resolved simultaneous measurement of temperature, absolute mole fractions of N2, O2, and H2, and two components of velocity in a Hencken burner flame were performed to demonstrate the technique.

Bivolaru, Daniel↗