Search NASA⌕ Search

Engineering topics

Tesch, W. A.

Publications and source records attributed to Tesch, W. A..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Blade row dynamic digital compression program. Volume 2: J85 circumferential distortion redistribution model, effect of Stator characteristics, and stage characteristics sensitivity study

The results of dynamic digital blade row compressor model studies of a J85-13 engine are reported. The initial portion of the study was concerned with the calculation of the circumferential redistribution effects in the blade-free volumes forward and aft of the compression component. Although blade-free redistribution effects were estimated, no significant improvement over the parallel-compressor type solution in the prediction of total-pressure inlet distortion stability limit was obtained for the J85-13 engine. Further analysis was directed to identifying the rotor dynamic response to spatial circumferential distortions. Inclusion of the rotor dynamic response led to a considerable gain in the ability of the model to match the test data. The impact of variable stator loss on the prediction of the stability limit was evaluated. An assessment of measurement error on the derivation of the stage characteristics and predicted stability limit of the compressor was also performed.

Tesch, W. A.↗
NASA NTRS1976

Linearized blade row compression component model. Stability and frequency response analysis of a J85-3 compressor

NASA developed stability and frequency response analysis techniques were applied to a dynamic blade row compression component stability model to provide a more economic approach to surge line and frequency response determination than that provided by time-dependent methods. This blade row model was linearized and the Jacobian matrix was formed. The clean-inlet-flow stability characteristics of the compressors of two J85-13 engines were predicted by applying the alternate Routh-Hurwitz stability criterion to the Jacobian matrix. The predicted surge line agreed with the clean-inlet-flow surge line predicted by the time-dependent method to a high degree except for one engine at 94% corrected speed. No satisfactory explanation of this discrepancy was found. The frequency response of the linearized system was determined by evaluating its Laplace transfer function. The results of the linearized-frequency-response analysis agree with the time-dependent results when the time-dependent inlet total-pressure and exit-flow function amplitude boundary conditions are less than 1 percent and 3 percent, respectively. The stability analysis technique was extended to a two-sector parallel compressor model with and without interstage crossflow and predictions were carried out for total-pressure distortion extents of 180 deg, 90 deg, 60 deg, and 30 deg.

Tesch, W. A.↗
NASA NTRS1976

Blade row dynamic digital compressor program. Volume 1: J85 clean inlet flow and parallel compressor models

The results are presented of a one-dimensional dynamic digital blade row compressor model study of a J85-13 engine operating with uniform and with circumferentially distorted inlet flow. Details of the geometry and the derived blade row characteristics used to simulate the clean inlet performance are given. A stability criterion based upon the self developing unsteady internal flows near surge provided an accurate determination of the clean inlet surge line. The basic model was modified to include an arbitrary extent multi-sector parallel compressor configuration for investigating 180 deg 1/rev total pressure, total temperature, and combined total pressure and total temperature distortions. The combined distortions included opposed, coincident, and 90 deg overlapped patterns. The predicted losses in surge pressure ratio matched the measured data trends at all speeds and gave accurate predictions at high corrected speeds where the slope of the speed lines approached the vertical.

Tesch, W. A.↗
NASA NTRS1976

Dynamic blade row compression component model for stability studies

This paper describes a generalized dynamic model which has been developed for use in compression component aerodynamic stability studies. The model is a one-dimensional, pitch-line, blade row, lumped volume system. Arbitrary placement of blade free volumes upstream, within, and downstream of the compression component as well as the removal of bleed flow from the exit of any rotor or stator are model options. The model has been applied to a two-stage fan and an eight-stage compressor. The clean inlet pressure ratio/flow maps and the surge line have been reproduced, thereby validating the capability of the dynamic model to reproduce the steady-flow characteristics of the compression component. A method for determining the onset of an aerodynamic instability which is associated with surge is described. Sinusoidally time-varying inlet and exit boundary conditions have been applied to the eight stage compressor as examples of the manner in which this model may be used for stability studies.

Tesch, W. A.↗