Engineering topics

Tevelde, J. A.

Publications and source records attributed to Tevelde, J. A..

5 records

NASA NTRS1982

Experimental study of external fuel vaporization

The fuel properties used in the design of a flash vaporization system for aircraft gas turbine engines were evaluated in experiments using a flowing system to determine critical temperature and pressure, boiling points, dew points, heat transfer coefficients, deposit formation rates, and deposit removal. Three fuels were included in the experiments: Jet-A, an experimental referree broad specification fuel, and a premium No. 2 diesel fuel. Engine conditions representing a NASA Energy Efficient Engine at sea-level take-off, cruise, and idle were simulated in the vaporization system and it was found that single phase flow was maintained in the heat exchanger and downstream of the throttle. Deposits encountered in the heat exchanger represented a thermal resistance as high as 1300 sq M K/watt and a deposit formation rate over 1000 gC/sq cm hr.

Szetela, E. J.↗

NASA NTRS1981

Autoignition characteristics of no. 2 diesel fuel

Parametric tests to map the ignition delay characteristics were conducted at pressures of 3, 4, and 5 atm, inlet air temperatures up to 1150 K and fuel air equivalence ratios ranging from 0.2 to 1.0. Ignition delay times in the range of 6 msec to 60 msec at freestream flow velocities ranging from 10 m/sec to 40 m/sec were obtained. The ignition delay times appeared to correlate with the inverse of pressure and the inverse exponent of temperature.

Tevelde, J. A.↗

NASA NTRS1981

Autoignition characteristics of aircraft-type fuels

An investigation was conducted of the ignition delay characteristics of five liquid hydrocarbon fuels in air. The test apparatus developed permitted independent variation and control of temperature, pressure, air flow rate, and fuel/air ratio in order that the effects of each parameter could be investigated independently. All of the fuels tested behaved in a predictable manner, that is, ignition delay time decreased as temperature, pressure, and fuel/air ratio increased. The results for the different fuels tested (Jet-A, MP-4, No. 2 diesel, ERBS, and cetane) were directly comparable, since it can be shown that the fuel spray characteristics from the multiple conical tube injector are relatively insensitive to small changes in fuel properties (viscosity, surface tension, and density).

Spadaccini, L. J.↗

NASA NTRS1980

Autoignition characteristics of aircraft-type fuels

The ignition delay characteristics of Jet A, JP 4, no. 2 diesel, cetane and an experimental referee broad specification (ERBS) fuel in air at inlet temperatures up to 1000 K, pressures of 10, 15, 20, 25 and 30 atm, and fuel air equivalence ratios of 0.3, 0.5, 0.7 and 1.0 were mapped. Ignition delay times in the range of 1 to 50 msec at freestream flow velocities ranging from 20 to 100 m/sec were obtained using a continuous flow test apparatus which permitted independent variation and evaluation of the effect of temperature, pressure, flow rate, and fuel/air ratio. The ignition delay times for all fuels tested appeared to correlate with the inverse of pressure and the inverse exponent of temperature. With the exception of pure cetane, which had the shortest ignition delay times, the differences between the fuels tested did not appear to be significant. The apparent global activation energies for the typical gas turbine fuels ranged from 38 to 40 kcal/mole, while the activation energy determined for cetane was 50 kcal/mole. In addition, the data indicate that for lean mixtures, ignition delay times decrease with increasing equivalence ratio. It was also noted that physical (apparatus dependent) phenomena, such as mixing (i.e., length and number of injection sites) and airstream cooling (due to fuel heating, vaporization and convective heat loss) can have an important effect on the ignition delay.

Spadaccini, L. J.↗

NASA NTRS1976

Shock wave ignition of metal powders

The interaction between isolated metal particles and shock-induced flowfields is analyzed to characterize physical events and determine experimental feasibility for shock wave ignition studies. Emphasis is placed on incident shock wave phenomenon as opposed to reflected shock wave. A pre-ignition particle-flow interaction is hypothesized which presumes a vapor phase ignition reaction and an absence of significant vaporization prior to particle melting and erosion. Rapid vaporization of eroded mass is expected, with ignition reaction in the particle wakes. Experimental observation of the 6438-A Cd line and the 3721-A MgO band support the ignition mechanism hypothesized. Scattered cloud data are believed to substantiate the hypothesis that ignition delays could be correlated with predicted melting times.

Fox, T. W.↗