Search NASA⌕ Search

Engineering topics

Thackeray, Michael M.

Publications and source records attributed to Thackeray, Michael M..

At least 19 records

Topotactic Phase Transformation of Lithiated Spinel to Layered LiMn0.5Ni0.5O2: The Interaction of 3-D and 2-D Li-ion Diffusion

This study investigates the structural evolution of LiMn0.5Ni0.5O2 cathode materials for Li-ion batteries as a function of synthesis temperature and its effect on electrochemical performance. It is demonstrated that, as the synthesis temperature increases from 400 to 900 ?C, a gradual topotactic transformation occurs between a lithiated spinel structure, denoted herein as “lithium-excess spinel” LxS-LiMn0.5Ni0.5O2 (or LxS-LMNO), and the well-known layered LiMn0.5Ni0.5O2 structure prepared at high temperature, HT-LiMn0.5Ni0.5O2 (HT-LMNO). The electrochemical capacity of the LiMn0.5Ni0.5O2 electrodes follows a parabolic trend with increasing synthesis temperature, which is attributed primarily to the gradual transformation of 3-dimensional (3-D) to 2-dimensional (2-D) diffusion pathways for the Li ions. When synthesized at 400 °C, LxS-LiMn0.5Ni0.5O2 electrodes perform well, benefitting from the 3-D network of channels within the LxS structure. By contrast, when prepared at 500-700 °C, LiMn0.5Ni0.5O2 electrodes operate poorly, which is attributed to the formation of locally disordered structural arrangements that impede Li-ion diffusion. Such an increase in local disorder in the mid-temperature synthesis range is attributed to the structural frustration between the lithium-excess spinal and layered end-members. The transformation from the locally disordered to more ordered layered components between 700 °C and 900 °C enhances electrochemical performance. The study opens new avenues for designing next-generation Mn-rich cathode materials by fine-tuning the synthesis conditions as well as the composition and structure of LxS-LMNO electrodes.

energy storage↗

Unraveling the Structure and Composition of Li 4 Mn 2 O 4.5 (Li 2 O·Li 0.667 Mn 1.333 O 2 ) Electrodes for Lithium Batteries Using a High-Temperature Synthesis Approach

This paper addresses the debate about the composition and structure of a lithium-rich manganese oxide electrode with a fully disordered rock salt component, Li 4 Mn 2 O 5 (or Li 2 O·2LiMnO 2 ), first reported by Freire et al. in 2016; it is typically prepared by a high-energy ball milling procedure. It has now been demonstrated that, when prepared at 800°C, the formula of this compound is Li 4 Mn 2 O 4.5 , alternatively Li 2 O·Li 0.667 Mn 1.333 O 2 , or close thereto. The cubic, disordered Li 0.667 Mn 1.333 O 2 (or Li 0.333 Mn 0.667 O) rock salt component, in which the manganese ions adopt an average oxidation state of 2.5+, transforms to a clearly-defined spinel configuration during electrochemical cycling. The electrochemical activation process that occurs during the initial charge reaction includes the oxidation of the manganese ions by oxygen released by the Li 2 O component between 4.5 and 4.6 V. In complete contrast, nickel- and nickel-cobalt-substituted electrodes, such as Li 2 O·2LiMn 0.5 Ni 0.5 O 2 (Li 4 MnNiO 5 ) and Li 2 O·2LiMn 0.475 Ni 0.475 Co 0.050 O 2 (Li 4 Mn 0.95 Ni 0.95 Co 0.10 O 5 ), in which the manganese ions adopt a tetravalent state, have completely disordered rock salt components that are electrochemically inactive.

25 ENERGY STORAGE↗

Lithium battery electrodes

Electrode materials for electrochemical cells and batteries and methods of producing such materials are disclosed herein. The electrode materials comprise an active lithium metal oxide material prepared by: (a) contacting the lithium metal oxide material with an aqueous acidic solution containing one or more metal cations; and (b) heating the so-contacted lithium metal oxide from step (a) to dryness at a temperature below 200° C. The metal cations in the aqueous acidic solution comprise one or more metal cations selected from the group consisting of an alkaline earth metal ion, a transition metal ion, and a main group metal ion.

25 ENERGY STORAGE↗

Review–From LiMn 2 O 4 to Partially-Disordered Li 2 MnNiO 4 : The Evolution of Lithiated-Spinel Cathodes for Li-Ion Batteries

This personal narrative relates to the discovery in 1981 of stoichiometric LiM 2 O 4 spinel electrodes (where M = metal cation) for lithium-ion batteries by the Goodenough group at Oxford University, UK, and the subsequent identification and evolution of stable lithiated-spinel Li 2 M 2 O 4 (or LiMO 2 ) cathodes at the Council for Scientific and Industrial Research in South Africa and Argonne National Laboratory (USA). In this work, the competition that occurs between the formation of lithiated-spinel and layered (LiMO 2 ) structures at 400 °C, and recent efforts to design high-capacity, Mn-rich composite cathodes with partial disorder, are discussed. The paper is written in honor of John Goodenough's 100th birthday.

25 ENERGY STORAGE↗

Cobalt-stabilized lithium metal oxide electrodes for lithium batteries

An electrode material comprising a composite lithium metal oxide, which in an initial state has the formula: y[xLi2MO3.(1−x)LiM′O2].(1−y)Li1+dMn2−z−dM″zO4; wherein 0≤x≤1; 0.75≤y<1; 0<z≤2; 0≤d≤0.2; and z−d≤2. M comprises one or more metal ions that together have an average oxidation state of +4; M′ comprises one or more metal ions that together have an average oxidation state of +3; and M″ comprises one or more metal ions that together with the Mn and any excess proportion of lithium, “d”, have a combined average oxidation state between +3.5 and +4. The Li1+dMn2−z−dM″zO4 component comprises a spinel structure, each of the Li2MO3 and the LiM′O2 components comprise layered structures, and at least one of M, M′, and M″ comprises Co. Cells and batteries comprising the electrode material also are described.

25 ENERGY STORAGE↗

Graphene-coated metal oxide spinel cathodes

Disclosed herein are graphene-coated lithium manganese oxide spinels cathodes for high-performance batteries Li-ion batteries and methods for making thereof. A single-layer graphene coating is shown to significantly reduce manganese loss in the cathodes while concurrently promoting the formation of a well-defined solid electrolyte interphase layer.

25 ENERGY STORAGE↗

Surface treatment for lithium battery electrode materials

Electrode materials for electrochemical cells and batteries and methods of producing such materials are disclosed herein. A method of preparing an active lithium metal oxide material suitable for use in an electrode for a lithium electrochemical cell comprises the steps of: (a) contacting the lithium metal oxide material with an aqueous acidic solution containing one or more metal cations; and (b) heating the so-contacted lithium metal oxide from step (a) to dryness at a temperature below 200° C. The metal cations in the aqueous acidic solution comprise one or more metal cations selected from the group consisting of an alkaline earth metal ion, a transition metal ion, and a main group metal ion.

25 ENERGY STORAGE↗

Exploiting the Spinel Structure for Li-ion Battery Applications: A Tribute to John B. Goodenough

This review provides a personal account of career-long efforts, interwoven with the contributions of others, to exploit the [B 2 ]O 4 framework of an A[B 2 ]O 4 spinel structure for lithium-ion battery applications, where A = Li, and B is one or more metal cations. The narrative begins at the Council for Scientific and Industrial Research (CSIR) in South Africa in the mid-1970s when, in response to the Middle East oil crisis, worldwide efforts were turned to develop high-temperature sodium and lithium batteries to power electric vehicles. In 1981, results in CSIR's program on a high-temperature lithium battery led to a collaborative project on room-temperature lithium cells with Prof. John B. Goodenough at Oxford University, where studies of Fe 3 O 4 , Mn 3 O 4 , and LiMn 2 O 4 cathodes led to the recognition of the broad utility of the [B2]O4 spinel framework as an anode, cathode, or solid electrolyte for rechargeable lithium cells. This finding has had a profound and lasting impact, influencing further ideas and discoveries at the CSIR, Argonne National Laboratory, and elsewhere. The narrative emphasizes the compositional versatility of the spinel structure and the opportunities to tailor the electrochemical potential and stability of a Li-ion cell.

25 ENERGY STORAGE↗

Layered-spinel electrodes for lithium batteries

An electrode for a lithium-ion cell comprising a ‘layered-spinel’ composite oxide material is disclosed. The ‘layered-spinel’ can be a material of formula xLiMO2.(1−x)LiyM′zO4, wherein 0 < x < 1; LiMO2 is a lithium metal oxide having a layered structure in which M comprises one or more transition metals and optionally lithium, and has a combined average oxidation state of +3; and LiyM′zO4 is a lithium metal oxide having a spinel structure, 1≤y≤1.33, 1.66≤z≤2, and M′ comprises one or more transition metals, and has a combined average metal oxidation state in the range of about +3.5 to about +4.

25 ENERGY STORAGE↗

Advancing Lithium- and Manganese-Rich Cathodes through a Combined Electrolyte Additive/Surface Treatment Strategy

Lithium- and manganese-rich (LMR) materials provide cost and environmental advantages to other competing cathodes based on nickel or cobalt chemistries. Within the LMR family, layered-layered-spinel (LLS) cathodes have unique properties, detailed herein, that address several of the challenges faced in large-scale implementation of LMR cathodes. This paper details how a LLS//graphite system was considerably improved by combining optimization strategies. First, a cathode surface-treatment process was optimized. Interestingly, cathodes surface-treated at a low temperature (similar to 100 degrees C) exhibited the best results. The optimized LLS cathode was tested vs. graphite using small amounts of lithium difluoro(oxalate)borate electrolyte additive. The combined approach improved various aspects of the electrochemical performance (e.g., impedance, cycle life, and coulombic efficiency) more than each strategy used alone by mitigating Mn dissolution from the cathode and the ensuing deposition on the anode. The report describes a unique method to improve the performance of practically relevant LMR//graphite cells.

25 ENERGY STORAGE↗

Development of manganese-rich cathodes as alternatives to nickel-rich chemistries

High-energy, inexpensive and safe electrochemistries have been the main goals of lithium-ion battery research for many years. Historically, manganese-based cathodes have long been studied for their attractive cost and safety characteristics [1]. However, due to issues related to both surface and bulk instabilities, manganese-rich electrodes have yet to find substantial success in the high-energy lithium-ion battery market. With current trends in cathode chemistries leaning heavily toward Ni-rich compositions, the factors of cost and safety are again at the forefront of research and development efforts. This paper reports the recent progress made at Argonne National Laboratory (USA) to stabilize manganese-rich cathode structures and surfaces with a specific focus on composite materials with intergrown layered and spinel components; it presents an overview of their electrochemical properties in terms of capacity, energy, and cycle-life in cells with metallic lithium, graphite, and Li 4 Ti 5 O 12 anodes. These layered-spinel cathodes show promise as alternatives to highly nickel-rich electrode compositions, which bodes well for continued advances.

25 ENERGY STORAGE↗

Stabilized electrodes for lithium batteries

A structurally inhomogeneous lithium metal oxide material having the Formula (I): y[xLi2MO3•(1-x)LiM′O2]•(1-y)Li1+dM″2−dO4; wherein 0≤x≤1; 0<y<1; 0≤d≤0.33; and wherein the Li1+dM″2−dO4 component comprises a spinel structure, and each of the Li2MO3 and the LiM′2 components thereof comprise layered structures. Each of M, M′, and M″ independently comprises one or more metal ions. The composition of the material of Formula (I) varies across the electrode particles by changing at least one of x, y, d, M, M′ and M″. Electrodes, cells and batteries comprising the lithium metal oxide material are also described.

Thackeray, Michael M.↗

Dynamic imaging of crystalline defects in lithium-manganese oxide electrodes during electrochemical activation to high voltage

Crystalline defects are commonly generated in lithium-metal-oxide electrodes during cycling of lithium-ion batteries. Their role in electrochemical reactions is not yet fully understood because, until recently, there has not been an effective operando technique to image dynamic processes at the atomic level. In this study, two types of defects were monitored dynamically during delithiation and concomitant oxidation of oxygen ions by using in situ high-resolution transmission electron microscopy supported by density functional theory calculations. One stacking fault with a fault vector b/6[110] and low mobility contributes minimally to oxygen release from the structure. In contrast, dissociated dislocations with Burgers vector of c/2[001] have high gliding and transverse mobility; they lead to the formation, transport and release subsequently of oxygen related species at the surface of the electrode particles. This work advances the scientific understanding of how oxygen participates and the structural response during the activation process at high potentials.

36 MATERIALS SCIENCE↗

Probing Electrochemically Induced Structural Evolution and Oxygen Redox Reactions in Layered Lithium Iridate

In order to exploit electrochemical capacity beyond the traditionally-utilized transition metal redox reactions in lithium-metal-oxide cathode materials, it is necessary to understand the role that oxygen ions play in the charge compensation mech-anisms, i.e., to know the conditions triggering electron transfer on the oxygen ions and whether this transfer is correlated with battery capacity. Theoretical and experimental investigations of a model cathode material, Li-rich layered Li 2 IrO 3 , have been performed to study the structural and electronic changes induced by electrochemical delithiation in a lithium-ion cell. First-principles density functional theory (DFT) calculations were used to compute the voltage profile of a Li/Li 2-x IrO 3 cell at various states of charge, and the results were in good agreement with electrochemical data. Electron energy loss spectroscopy (EELS), X-ray absorption near-edge spectroscopy (XANES), resonant/non-resonant X-ray emission spectroscopy (XES), and first principles core-level spectra simulations using the Bethe Salpeter Equation (BSE) approach were used to probe the change in oxygen electronic states over the $x$ = 0 to 1.5 range. The correlated Ir M 3 -edge XANES and O K-edge XANES data provided evidence that oxygen hole states form during the early stage of delithiation at ~3.5 V due to the interaction between O $p$ and Ir $d$ states, with Ir oxidation being the dominant source of electrochemical capacity. At higher potentials, the charge capacity was predominantly attributed to oxidation of the O 2- ions. It is argued that the emergence of oxygen holes alone is not necessarily indicative of electrochemical capacity beyond transition metal oxidation, since oxygen hole states can appear as a result of enhanced mixing of O $p$ and Ir $d$ states. Prevailing mechanisms accounting for the oxygen redox mechanism in Li-rich materials were examined by theoretical and experimental X-ray spectroscopy; however, no unambiguous spectroscopic signatures of oxygen dimer interaction or non-bonding oxygen states were identified.

25 ENERGY STORAGE↗

Identifying the Chemical Origin of Oxygen Redox Activity in Li-Rich Anti-Fluorite Lithium Iron Oxide by Experimental and Theoretical X-ray Absorption Spectroscopy

Harnessing oxygen redox reactions is an intriguing route to increasing capacity in Li-ion batteries (LIBs). Despite numerous experimental and theoretical attempts to unravel the mechanism of oxygen redox behavior, the electronic origin of oxygen activities in energy storage of Li-rich LIB materials remains under intense debate. In this work, the onset of oxygen activity was examined using a Li-rich material that has been reported to exhibit oxygen redox, namely, Li 5 FeO 4 . By comparing experimental measurements and first-principles Bethe-Salpeter equation calculations of oxygen K-edge X-ray absorption spectra (XAS), it was found that experimentally-observed changes in XAS originate from the non-bonding oxygen states in cation-disordered delithiated Li 5 FeO 4 , and the spectral features of oxygen dimers were also determined. This combined experimental and theoretical study offers an effective approach to disentangle the intertwined signals in XAS and can be further utilized in broader contexts for characterizing other energy storage and conversion materials.

25 ENERGY STORAGE↗

Cobalt-stabilized lithium metal oxide electrodes for lithium batteries

An electrode material comprising a composite lithium metal oxide, which in an initial state has the formula: y[xLi 2 MO 3 .(1-x)LiM'O 2 ].(1-y)Li 1+d Mn 2-z-d M" -z O 4 ; wherein 0.ltoreq.x.ltoreq.1; 0.75.ltoreq.y<1; 0 1+d Mn 2-z-d M" z O 4 component comprises a spinel structure, each of the Li 2 MO 3 and the LiM'O 2 components comprise layered structures, and at least one of M, M', and M" comprises Co. Cells and batteries comprising the electrode material also are described.

Thackeray, Michael M.↗

First-Principles Study of Lithium Cobalt Spinel Oxides: Correlating Structure and Electrochemistry

Embedding a lithiated cobalt oxide spinel (Li 2 Co 2 O 4 , or LiCoO 2 ) component or a nickel-substituted Li2Co 1-x NixO 2 analogue in structurally integrated cathodes such as xLi 2 MnO 3 .(1-x)LiM'O 2 (M' = Ni/Co/Mn) has been recently proposed as an approach to advance the performance of lithium-ion batteries. Here, we first revisit the phase stability and electrochemical performance of LiCoO 2 synthesized at different temperatures using density functional theory calculations. Consistent with previous studies, we find that the occurrence of low- and high-temperature structures (i.e., cubic lithiated spinel LT-LiCoO 2 ; or Li 2 Co 2 O 4 (Fd$\overline{3m}$) vs trigonal-layered HT-LiCoO 2 (R$\overline{3m}$), respectively) can be explained by a small difference in the free energy between these 20 30 40 50 60 70 80 26 two compounds. Additionally, the observed voltage profile of a Li/LiCoO 2 cell for both cubic and trigonal phases of LiCoO 2 , as well as the migration barrier for lithium diffusion from an octahedral (O h ) site to a tetrahedral site (T d ) in Fd$\overline{3m}$ LT-Li 1-x CoO 2 , has been calculated to help understand the complex electrochemical charge/discharge processes. A search of LiCo x M 1-x O 2 lithiated spinel (M' = Ni or Mn) structures and compositions is conducted to extend the exploration of the chemical space of Li-Co-Mn-Ni-O electrode materials. We predict a new lithiated spinel material, LiNi 0.8125 Co 0.1875 O 2 (Fd$\overline{3m}$), with a composition close to that of commercial, layered LiNi 0.8 Co 0.05 Al 0.05 O 2 , which may have the potential for exploitation in structurally integrated, layered spinel cathodes for next generation lithium-ion batteries.

25 ENERGY STORAGE↗