Search NASA⌕ Search

Engineering topics

Thareja, Rajiv R.

Publications and source records attributed to Thareja, Rajiv R..

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Computational studies of a fluid spike as a leading edge protection device for shock-shock interference heating

The effectiveness of a fluid spike as a device to protect leading edges of hypersonic atmospheric flight vehicles from high aerothermal loads produced by complex shock-shock interference is studied. The two-dimensional Navier-Stokes equations are solved using an unstructured cell-centered, fully implicit, flux-difference split algorithm. Adaptively generated unstructured meshes are employed. A type IV shock-shock interference for Mach 8 flow on a cylindrical leading edge with and without a small contraflow supersonic jet (fluid spike) placed at two different locations on the body is solved. A typical flow past a blunt body with a type IV shock-shock interference produces very high pressures and heat fluxes on the leading edge. Present results indicate that a fluid spike displaces the bow shock further in front of the body and modifies the shock-shock interference pattern. This leads to reduced peak pressures and heat fluxes on the body.

Prabhu, Ramadas K.↗
NASA NTRS1990

Shock interference studies on a circular cylinder at Mach 16

This paper presents the results of a computational study on the shock interference problems on a cylindrical body typical of an engine inlet cowl leading edge at a nominal Mach number of 16. The two-dimensional Navier-Stokes equations are solved assuming the flow to be in chemical and thermal equilibrium and using a finite element method. The algorithm employs a cell-centered fully implicit upwind scheme. Adaptively generated unstructured meshes of triangles and quadrilaterals are employed. Under certain conditions the finite element code resulted in oscillatory solutions for shock interference at Mach 16. Some of the causes of the unsteady behavior are identified, and to the extent possible, such situations are avoided in the present application. Two shock interference conditions involving a Type IV (supersonic jet) and a Type III (attaching shear layer) are solved. The results are compared with available experimental data and reasonable agreement is observed. A semi-empirical method is also used to estimate the maximum surface heat flux and static pressure.

Prabhu, Ramadas K.↗
NASA NTRS1989

A three-dimensional upwind finite element point implicit unstructured grid Euler solver

A three-dimensional upwind finite element technique that uses cell-centered quantities and implicit and/or explicit time marching was developed for computing hypersonic inviscid flows using adaptive unstructured grids. This technique was used to predict shock interference on a swept cylinder. An attempt was made to determine the flowfield and, in particular, the pressure augmentation caused by an impinging shock on the swept leading edge of a cowl lip of an engine inlet.

Thareja, Rajiv R.↗
NASA NTRS1989

A Navier-Stokes solver for high speed equilibrium flows and application to blunt bodies

This paper presents a finite element method for the solution of Navier-Stokes equations with the assumption of thermodynamic and chemical equilibrium. The method employs an upwind finite element technique with an implicit time-marching scheme for the solution, and uses an adaptively generated unstructured triangular mesh with several layers of quadrilateral elements near solid walls. The complexity associated with the assumption that the flow is in equilibrium is treated consistently, and the inviscid flux Jacobian matrices are derived. Several problems involving inviscid and viscous hypersonic flow past blunt are solved. Results are compared with other numerical results and experimental data, and generally good agreement is observed.

Prabhu, Ramadas K.↗
NASA NTRS1989

Euler and Navier-Stokes solutions for hypersonic flows

An upwind finite-element technique that uses cell-centered quantities and implicit and/or explicit time marching has been developed for computing hypersonic laminar viscous flows using adaptive unstructured grids in two and three dimensions. A perfect gas model as well as an equilibrium air model is implemented for solving high-speed flows. A first-order basic scheme and a higher-order flux-corrected transport (FCT) scheme have been implemented. This technique has been used to predict 'Type III and IV' shock interactions on a cylinder in two dimensions and a swept cylinder in three dimensions, with a view to determine the pressure and heating rate augmentation caused by an impinging shock on the leading edge of a cowl lip of an engine inlet. The predictions of wall pressure and heating rates compare very well with experimental data. The flow features are very distinctly captured with a sequence of adaptively-generated grids. Three-dimensional corner flow, typically encountered in engine inlets due to compression of the flow by ramps in the walls, is also modeled. This procedure is the first step in developing an integrated fluid, thermal, structural analysis capability for hypersonic flight vehicles like the National Aero-Space Plane.

Thareja, Rajiv R.↗
NASA NTRS1988

A point implicit unstructured grid solver for the Euler and Navier-Stokes equations

An upwind finite element technique that uses cell centered quantities and implicit and/or explicit time marching has been developed for computing hypersonic laminar viscous flows using adaptive unstructured triangular grids. A structured grid of quadrilaterals is laid out near the body surface. For inviscid flows the method is stable at Courant numbers of over 100,000. A first order basic scheme and a higher order flux corrected transport (FCT) scheme have been implemented. This technique has been applied to the problem of predicting type III and IV shock wave interactions on a cylinder, with a view of simulating the pressure and heating rate augmentation caused by an impinging shock on the leading edge of a cowl lip of an engine inlet. The predictions of wall pressure and heating rates compare very well with experimental data. The flow features are very distinctly captured with a sequence of adaptively generated grids. The adaptive mesh generator and the upwind Navier-Stokes solver are combined in a set of programs called LARCNESS, an acronym for Langley Adaptive Remeshing Code and Navier-Stokes Solver.

Thareja, Rajiv R.↗
NASA NTRS1988

Application of finite element and remeshing technique to shock interference on a cylindrical leading edge

The problem of planar oblique shock impingement on a cylindrical leading edge in hypersonic flow is modeled using a Galerkin-Runge Kutta finite element method. The method utilizes a four stage Runge-Kutta time stepping scheme to solve the compressible Euler equations. Freestream Mach numbers of 6.5, 8.0 and 16.0 are studied. The computed surface pressure distributions consistently agree well with available experimental data. The peak pressure amplification ranges from 5.45 at M = 6.5 to approximately 17.0 at M = 16.0. Stagnation point heat transfer rate amplifications are calculated from the inviscid solution using the method of Fay and Riddell. The value and wall location of the peak pressure and heat transfer rate amplifications are extremely sensitive to the location of the impinging shock/bow shock intersection point.

Stewart, James R.↗
NASA NTRS1987

Efficient single-level solution of hierarchical problems in structural optimization

A demonstration is made of the use of single-level hierarchical solution techniques for engineering design, which, unlike the formulation stage-applied multilevel techniques, are applied at the solution stage. A single-level decomposition technique is developed which reduces computational costs and memory requirements without incurring the disadvantages of multilevel optimization. Savings of 75 percent are obtained in a case involving 500 design variables and 2408 constraints.

Thareja, Rajiv R.↗