Engineering topics

Thomas, Randy

Publications and source records attributed to Thomas, Randy.

7 records

NASA NTRS2020

Combustion Dynamics Characteristics and Fuel Pressure Modulation Responses of a Three-Cup Third-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

This paper presents the combustion dynamic data and fuel modulation response of a three-cup Lean Direct Injection combustor developed by Woodward, FST. The test was conducted at the NASA Glenn Research Center CE-5 flame tube test facility. The facility provided inlet air up to 922 K and pressure up to 19.0 bar. At the low-power configuration, the combustion noise was quiet. Large combustion pressure oscillations were observed with the High-power configuration at an off design condition, with low inlet air temperature and pressure conditions and a high equivalence ratio (about T3=600 K, P3 = 800 kPa, and ER =0.46). The noise amplitude was as high as 1.5 psi at around 220 Hz. As inlet air pressure and temperature increased, this combustion instability decreased. Fuel modulated signals were produced with the WASK fuel modulator located in the fuel line upstream of the center cup pilot fuel-air mixer. The amplitudes of the modulated signals detected in the combustor were low. Only less than 0.13% (0.06 psi) of the input energy was detected, and the signal amplitudes decreased as the modulated frequencies increased. Interaction between the modulated signals and the combustion noise varied with operating conditions. At a condition with low combustion noise around 150 hz, modulating a signal at around the same frequency would increase the combustion noise from 0.2 psi to as high as 0.6 psi, whereas at a condition with a high combustion instability around 250 hz, the modulated signal did not seem to have much effect on the combustion noise.

Fuel flexible combustor↗

NASA NTRS2018

An Overview of High Bandwidth Liquid Fuel Flow Modulators Developed for Active Combustion Control Research

This paper presents a description of the general construction of three high bandwidth liquid fuel modulators along with data corresponding to their respective modulation performance. These devices are a critical element of the National Aeronautics and Space Administration Glenn Research Center's (NASA GRC) Active Combustion Control (ACC) task. These devices are not commercially-off-the-shelf available, primarily due to a one kHz bandwidth requirement. Given their special nature, NASA GRC developed specifications for the modulation devices and then, through Small Business Innovative Research (SBIR) contracts, had vendors with expertise in valve design manufacture them. The modulators described in this paper are the Active Signal Modulator (ASM), the Jansen's Aircraft System Controls (JASC) modulator, and the WASK Engineering (WASK) modulator. These modulators utilize magnetostrictive, electric motor, or piezoelectric actuation, respectively. The specifications for these devices evolved over time to meet the needs of changing objectives in the ACC research task. This is primarily true with respect to flow number as their designs accommodate a range from one to eight (lbm./hr-psi0.5). These designs also exhibit relatively small volume, weight, and power consumption with an ability to modulate approximately +/- 30% from the mean on a pressure basis. The modulators have been characterized and have undergone laboratory performance tests by the vendors. Their data indicated suitability for continued use in ACC research testing.

Saus, Joseph R.↗

NASA NTRS2018

In-Line Electromagnetic Actuator for Fuel Modulation

An in-line electromagnetic actuator with normally-open configuration has been developed for the purpose of exploring its application as a fuel modulator for the active control of combustor thermo-acoustic instabilities. The actuator is based on the spring-coil-plunger mechanism with the plunger designed to be suspended by crossed cantilever beam springs. Operational specification was set for a 1000 psi maximum inlet fuel pressure and modulation for a broad frequency bandwidth that encompasses frequencies that are typically associated with combustor thermo-acoustic instabilities. Various test results demonstrated fuel modulation up to 1200 Hz for coil excitation voltage between 2.3 and 4.6 V and current between 16 and 48 mA, respectively. The initial goal of this work was to demonstrate fuel modulation based on the concept of a normally-open fuel modulator with tethered plunger displacement.

Actuator↗

NASA NTRS2018

In-Line Electromagnetic Actuator for Fuel Modulation

Okojie, Robert S.↗

NASA NTRS2013

Combined Cycle Engine Large-Scale Inlet for Mode Transition Experiments: System Identification Rack Hardware Design

The System Identification (SysID) Rack is a real-time hardware-in-the-loop data acquisition (DAQ) and control instrument rack that was designed and built to support inlet testing in the NASA Glenn Research Center 10- by 10-Foot Supersonic Wind Tunnel. This instrument rack is used to support experiments on the Combined-Cycle Engine Large-Scale Inlet for Mode Transition Experiment (CCE‒ LIMX). The CCE‒LIMX is a testbed for an integrated dual flow-path inlet configuration with the two flow paths in an over-and-under arrangement such that the high-speed flow path is located below the lowspeed flow path. The CCE‒LIMX includes multiple actuators that are designed to redirect airflow from one flow path to the other; this action is referred to as "inlet mode transition." Multiple phases of experiments have been planned to support research that investigates inlet mode transition: inlet characterization (Phase-1) and system identification (Phase-2). The SysID Rack hardware design met the following requirements to support Phase-1 and Phase-2 experiments: safely and effectively move multiple actuators individually or synchronously; sample and save effector control and position sensor feedback signals; automate control of actuator positioning based on a mode transition schedule; sample and save pressure sensor signals; and perform DAQ and control processes operating at 2.5 KHz. This document describes the hardware components used to build the SysID Rack including their function, specifications, and system interface. Furthermore, provided in this document are a SysID Rack effectors signal list (signal flow); system identification experiment setup; illustrations indicating a typical SysID Rack experiment; and a SysID Rack performance overview for Phase-1 and Phase-2 experiments. The SysID Rack described in this document was a useful tool to meet the project objectives.

Thomas, Randy↗

NASA NTRS2013

Integrated Tools for Future Distributed Engine Control Technologies

Turbine engines are highly complex mechanical systems that are becoming increasingly dependent on control technologies to achieve system performance and safety metrics. However, the contribution of controls to these measurable system objectives is difficult to quantify due to a lack of tools capable of informing the decision makers. This shortcoming hinders technology insertion in the engine design process. NASA Glenn Research Center is developing a Hardware-inthe- Loop (HIL) platform and analysis tool set that will serve as a focal point for new control technologies, especially those related to the hardware development and integration of distributed engine control. The HIL platform is intended to enable rapid and detailed evaluation of new engine control applications, from conceptual design through hardware development, in order to quantify their impact on engine systems. This paper discusses the complex interactions of the control system, within the context of the larger engine system, and how new control technologies are changing that paradigm. The conceptual design of the new HIL platform is then described as a primary tool to address those interactions and how it will help feed the insertion of new technologies into future engine systems.

Culley, Dennis↗

NASA NTRS2007

Concepts for Distributed Engine Control

Gas turbine engines for aero-propulsion systems are found to be highly optimized machines after over 70 years of development. Still, additional performance improvements are sought while reduction in the overall cost is increasingly a driving factor. Control systems play a vitally important part in these metrics but are severely constrained by the operating environment and the consequences of system failure. The considerable challenges facing future engine control system design have been investigated. A preliminary analysis has been conducted of the potential benefits of distributed control architecture when applied to aero-engines. In particular, reductions in size, weight, and cost of the control system are possible. NASA is conducting research to further explore these benefits, with emphasis on the particular benefits enabled by high temperature electronics and an open-systems approach to standardized communications interfaces.

Culley, Dennis E.↗