Engineering topics

Thome, K. E. (ORCID:0000000248013922)

Publications and source records attributed to Thome, K. E. (ORCID:0000000248013922).

13 records

DOE OSTI2025

Propagation of ion cyclotron emission in the DIII-D tokamak

Experiments in L- and H-mode plasmas performed on the DIII-D tokamak explored ion cyclotron emission (ICE) propagation via the recently upgraded ICE diagnostic. The distance between the plasma and the outer wall was scanned to alter the evanescent region, which was seen to impact the detection of runaway electron-driven whistler modes in a comparable frequency range to typical ICE harmonics (f≳10fci) [Heidbrink et al., Plasma Phys. Controlled Fusion 61, 014007 (2018)]. In L-mode plasmas, core ICE did not exhibit clear trends as the plasma-wall distance was altered. Instead, inadvertent changes to the fast ion density correlated with different ICE fine structures; the most spectral bands (spaced ∼150–200 kHz apart) were observed at the highest fast ion density, and a just single band when nfast decreased by ∼ 40%. The full-wave Petra-M code simulated core ICE propagation through the plasma and to ICE probes, agreeing with experimental findings that these are likely compressional fast waves, which propagate to probe locations with no dependence on plasma-wall gap. Edge ICE in H-mode plasmas was similarly unaffected by plasma-wall distance. Unlike in core ICE cases, there were negligible changes to the edge fast ion distribution and edge bulk plasma profiles. However, changes in ELM frequency seemed most closely tied to ICE behavior. Ultimately, core and edge ICE did not exhibit clear dependencies on the plasma-wall distance, and ICE harmonics were observed with even the largest plasma-wall gaps. This independence bodes well for similar diagnostics in future tokamaks, which might be placed further from high radiation areas without adversely impacting measurement capabilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Understanding the L-H isotope effect at the DIII-D tokamak and advancements in synthetic turbulence diagnostics

Abstract It is determined that while heat flux differences between hydrogen and deuterium isotope experiments result from natural differences in carbon impurity content at DIII-D, it is not the origin of the low to high confinement mode (L-H) transition isotope effect. More specifically, a two times larger edge radial electric field in hydrogen compared to deuterium is uncovered and believed to play an important role. The origin of this radial electric field difference is determined to have two possible origins: differences in poloidal rotation and turbulent Reynolds stress in the closed field line region, and increased outer strike point temperatures and space potentials on open field lines. Experimental observations from both profile and turbulence diagnostics are supported by nonlinear gyrokinetic simulations using the code CGYRO. Simulations illustrated heat transport isotope effects in the plasma edge and shear layer resulting from differences in impurity content, electron non-adiabaticity, and main ion mass dependent E × B shear stabilization. Turbulence prediction comparisons from flux-matched CGYRO simulations to experimental measurements including electron temperature, density and velocity fluctuations are found to be in good agreement with available data. A dedicated DIII-D experiment in hydrogen was performed to seed more carbon than naturally occurring, to match deuterium experiments, and possibly reduce the L-H power threshold based on gyro-kinetic predictions. To our surprise, while ion temperature gradient (ITG) turbulence was stabilized, nodiscernible change in L-H power threshold were observed in these special hydrogen experiments. In particular, it is noticed that the edge radial electric field and Reynolds stress were observed as nearly unchanging in the presence of ITG stabilization. These experimental data have enabled a more comprehensive picture of the multitude of isotope effects at play in fusion experiments, and the important potential connection between the confined and unconfined plasma regions in regulating L-H transition dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Characterization of the ELM-free negative triangularity edge on DIII-D

Tokamak plasmas with strong negative triangularity (NT) shaping typically exhibit fundamentally different edge behavior than conventional L-mode or H-mode plasmas. On DIII-D, every plasma with sufficiently negative triangularity (δ < δ crit ≃ -0.12) is found to be inherently free of edge localized modes (ELMs), even at injected powers well above the predicted L-H power threshold. It is also possible to access an ELM free state at weaker average triangularities provided that at least one of the two x-points is still sufficiently negative. Access to the ELM-free NT scenario is found to coincide with the closure of the second stability region for infinite-n ballooning modes, suggesting that ballooning stability may play a role in limiting the accessible pressure gradient in NT plasmas. Despite this, NT plasmas are able to support small pedestals and are typically characterized by an enhancement of edge pressure gradients beyond those found in traditional L mode plasmas. Further, the pressure gradient inside of this small pedestal is unusually steep, allowing access to high core performance that is competitive with other ELM-free regimes previously achieved on DIII-D. Since ELM-free operation in NT is linked directly to the magnetic geometry, NT fusion pilot plants are predicted to maintain advantageous edge conditions even in burning plasma regimes, potentially eliminating reactor core-integration issues caused by ELMs.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

NSTX-U research advancing the physics of spherical tokamaks

Abstract The objectives of NSTX-U research are to reinforce the advantages of STs while addressing the challenges. To extend confinement physics of low- A , high beta plasmas to lower collisionality levels, understanding of the transport mechanisms that set confinement performance and pedestal profiles is being advanced through gyrokinetic simulations, reduced model development, and comparison to NSTX experiment, as well as improved simulation of RF heating. To develop stable non-inductive scenarios needed for steady-state operation, various performance-limiting modes of instability were studied, including MHD, tearing modes, and energetic particle instabilities. Predictive tools were developed, covering disruptions, runaway electrons, equilibrium reconstruction, and control tools. To develop power and particle handling techniques to optimize plasma exhaust in high performance scenarios, innovative lithium-based solutions are being developed to handle the very high heat flux levels that the increased heating power and compact geometry of NSTX-U will produce, and will be seen in future STs. Predictive capabilities accounting for plasma phenomena, like edge harmonic oscillations, ELMs, and blobs, are being tested and improved. In these ways, NSTX-U researchers are advancing the physics understanding of ST plasmas to maximize the benefit that will be gained from further NSTX-U experiments and to increase confidence in projections to future devices.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2024

High performance power handling in the absence of an H-mode edge in negative triangularity DIII-D plasmas

Abstract Experiments performed during strongly-shaped high-power diverted negative triangularity (NT) experiments in DIII-D achieved detached divertor conditions and a transient-free edge, showcasing the potential for application of NT to a core-edge integrated reactor-like scenario and providing the first characterization of the parametric dependencies for detachment onset. Detached divertor conditions will be required in future devices to mitigate divertor heat fluxes. Access to dissipative divertor conditions was investigated via an increase in upstream density. Detachment onset at the outer strike point was achieved with H-mode level confinement H 98 − y 2 ∼ 1 and reactor-relevant normalized pressures β N ∼ 2 . Confinement degradation was observed with deeper detachment, associated with the loss of an electron temperature pedestal. Differences in geometry, radial transport, impact of cross field drifts are discussed to explain differences in access to detachment in NT discharges. Higher normalized densities, with respect to equivalent discharges in positive triangularity, were necessary to achieve detachment, partially explained by the shorter parallel connection length to the targets. The effect of cross-field particle drifts ( E × B , B × ∇ B ) on access to detachment was demonstrated by the lower upstream density needed to access detachment with ion B × ∇ B drift directed outside of the active divertor (Greenwald fraction f Gw ∼ 0.9–1.0 vs f Gw ∼ 1.3). The upstream density at detachment onset was observed to increase linearly with plasma current with ion B × ∇ B drift into the divertor, consistent with the observed narrowing of the scrape-off layer heat flux width λ q . Edge fluid simulations capture separatrix densities needed to achieve detachment in NT plasma and their dependence on drift direction. The ability to reproduce detachment dynamics in NT plasma increases the confidence in future design studies for NT divertors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Isotope impact on Alfvén eigenmodes and fast ion transport in DIII-D

Abstract Measurements of beam driven Alfvén Eigenmode (AE) activity in matched deuterium (D) and hydrogen (H) DIII-D plasmas show a dramatic difference in unstable mode activity and fast ion transport for a given injected beam power. The dependence of the unstable AE spectrum in reversed magnetic shear plasmas on beam and thermal species is investigated in the current ramp by varying beam power in a sequence of discharges for fixed thermal and beam species at fixed density. In general, a spectrum of Reversed Shear Alfvén Eigenmodes (RSAEs) and Toroidal Alfvén Eigenmodes (TAEs) are driven unstable with sub-Alfvénic D beam injection while primarily only RSAEs are driven unstable for the H beam cases investigated. Further, for a given beam power, the driven AE amplitude is always reduced with H beams relative to D and for H thermal plasma relative to pure D or mixed D/H plasmas. Estimates of the fast ion stored energy combined with modeling using the hybrid kinetic-MHD code MEGA indicate that the dominant mechanism contributing to the difference between H and D beam drive is the faster classical slowing down of H beam ions relative to D and the resultant lower beam ion pressure. Calculations of the AE induced stored energy deficits using the reduced critical gradient model TGLFEP show quantitative agreement with the observed dependencies on injected power, isotope and minimum safety factor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

The role of isotope mass on neutral fueling and density pedestal structure in the DIII-D tokamak

Abstract Experimental measurements on DIII-D of hydrogen neutral penetration lengths ( λ n 0 ) on the high field side (HFS) are longer by a factor of 2 than for deuterium consistent with the thermal velocity ratio for neutrals at the same temperature ( v t h H / v t h D = 2 ) . This ratio is constant for both low and high pedestal electron density. At low pedestal density ( n e ∼ 4 × 10 19 m − 3 ) , the neutral penetration length is greater than the density pedestal width for both isotopes, and the additional 40% increase of neutral penetration in hydrogen widens the pedestal by the same amount. As the density pedestal height increases ( n e ∼ 6 × 10 19 m − 3 ) , the neutral penetration lengths drop below the density pedestal widths for both isotopes, and the increased penetration of hydrogen has no increased effect on the pedestal width compared to deuterium. Extrapolating to future reactor-relevant high electron density pedestals, the isotope-mass change in neutral fueling on the HFS from the deepest neutral penetration of hydrogen, to the shortest neutral penetration of tritium will be negligible (0.2–0.4 cm) in comparison to estimates of the density pedestal width (6–8.5 cm).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Density wavenumber spectrum measurements, synthetic diagnostic development, and tests of quasilinear turbulence modeling in the core of electron-heated DIII-D H-mode plasmas

Abstract Measurements of the turbulent density wavenumber spectrum, δ n ˆ e ( k ⊥ ) , using the Doppler Back-Scattering (DBS) diagnostic are reported from DIII-D H-mode plasmas with electron cyclotron heating as the only auxiliary heating method. These electron-heated plasmas have low collisionality, ν e ∗ < 1 , T e / T i > 1 , and zero injected torque—a regime expected to be relevant for future fusion devices. We probe density fluctuations in the core ( ρ ≈ 0.7) over a broad wavenumber range, 0.5 ⩽ k ⊥ ⩽ 16 cm −1 ( 0.1 ⩽ k ⊥ ρ s ⩽ 5 ), to characterize plasma instabilities and compare with theoretical predictions. We present a novel synthetic DBS diagnostic to relate the back-scattered power spectrum, P s ( k ⊥ ) —which is directly measured by DBS—to the underlying electron density fluctuation spectrum, δ n ˆ e ( k ⊥ ) . The synthetic DBS P s ( k ⊥ ) spectrum is calculated by combining the SCOTTY beam-tracing code with a model δ n ˆ e ( k ⊥ ) predicted either analytically or numerically. In this work we use the quasi-linear code Trapped Gyro-Landau Fluid (TGLF) to approximate the δ n ˆ e ( k ⊥ ) spectrum. We find that TGLF, using the experimental profiles, is capable of closely reproducing the DBS measurements. Both the DBS measurements and the TGLF-DBS synthetic diagnostic show a wavenumber spectrum with variable decay. The measurements show weak decay ( k −0.6 ) for k < 3.5 cm −1 , with k −2.6 at intermediate- k ( 3.5 ⩽ k ⩽ 8.5 cm −1 ), and rapid decay ( k −9.4 ) for k > 8.5 cm −1 . Scans of physics parameters using TGLF suggest that the normalized ∇ T e scale-length, R / L T e , is an important factor for distinguishing microturbulence regimes in these plasmas. A combination of DBS observations and TGLF simulations indicate that fluctuations remain peaked at ITG-scales (low k ) while R / L T e -driven TEM/ETG-type modes (intermediate/high k ) are marginally sub-dominant.

synthetic diagnostics↗

DOE OSTI2023

Robust Avoidance of Edge-Localized Modes alongside Gradient Formation in the Negative Triangularity Tokamak Edge

In a series of high performance diverted discharges on DIII-D, we demonstrate that strong negative triangularity (NT) shaping robustly suppresses all edge-localized mode (ELM) activity over a wide range of plasma conditions: ⟨n⟩ = 0.1 − 1.5 × 1020 m−3, Paux = 0 − 15 MW and |Bt| = 1 − 2.2 T, corresponding to Ploss/PLH08 ∼ 8. The full dataset is consistent with the theoretical prediction that magnetic shear in the NT edge inhibits access to ELMing H-mode regimes; all experimental pressure profiles are found to be at or below the infinite-n ballooning stability limit. Our present dataset also features edge pressure gradients in strong NT that are closer to an H–mode than a typical L-mode plasma, supporting the consideration of NT for reactor design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

On the origin of the DIII-D L-H power threshold isotope effect

Abstract The increased low to high confinement mode (L to H-mode) power threshold P L H in DIII-D low collisionality hydrogen plasmas (compared to deuterium) is shown to result from lower impurity (carbon) content, consistent with reduced (mass-dependent) physical and chemical sputtering of graphite. Trapped gyro-Landau fluid (TGLF) quasilinear calculations and local non-linear gyrokinetic CGYRO simulations confirm stabilization of ion temperature gradient (ITG) driven turbulence by increased carbon ion dilution as the most important isotope effect. In the plasma edge, electron non-adiabaticity is also predicted to contribute to the isotope dependence of thermal transport and P L H , however its effect is subdominant compared to changes from impurity isotopic behavior. This L-H power threshold reduction with increasing carbon content at low collisionality is in stark contrast to high collisionality results, where additional impurity content appears to increase the power necessary for H-mode access.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Flexible, integrated modeling of tokamak stability, transport, equilibrium, and pedestal physics

The STEP (Stability, Transport, Equilibrium, and Pedestal) integrated-modeling tool has been developed in OMFIT to predict stable, tokamak equilibria self-consistently with core-transport and pedestal calculations. STEP couples theory-based codes to integrate a variety of physics, including magnetohydrodynamic stability, transport, equilibrium, pedestal formation, and current-drive, heating, and fueling. The input/output of each code is interfaced with a centralized ITER-Integrated Modelling & Analysis Suite data structure, allowing codes to be run in any order and enabling open-loop, feedback, and optimization workflows. This paradigm simplifies the integration of new codes, making STEP highly extensible. STEP has been verified against a published benchmark of six different integrated models. Core-pedestal calculations with STEP have been successfully validated against individual DIII-D H-mode discharges and across more than 500 discharges of the H98,y2 database, with a mean error in confinement time from experiment less than 19%. STEP has also reproduced results in less conventional DIII-D scenarios, including negative-central-shear and negative-triangularity plasmas. Predictive STEP modeling has been used to assess performance in several tokamak reactors. Simulations of a high-field, large-aspect-ratio reactor show significantly lower fusion power than predicted by a zero-dimensional study, demonstrating the limitations of scaling-law extrapolations. STEP predictions have found promising scenarios for an EXhaust and Confinement Integration Tokamak Experiment, including a high-pressure, 80%-bootstrap-fraction plasma. ITER modeling with STEP has shown that pellet fueling enhances fusion gain in both the baseline and advanced-inductive scenarios. Finally, STEP predictions for the SPARC baseline scenario are in good agreement with published results from the physics basis.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Investigation of core impurity transport in DIII-D diverted negative triangularity plasmas

Abstract Tokamak operation at negative triangularity has been shown to offer high energy confinement without the typical disadvantages of edge pedestals (Marinoni et al 2021 Nucl. Fusion 61 116010). In this paper, we examine impurity transport in DIII-D diverted negative triangularity experiments. Analysis of charge exchange recombination spectroscopy reveals flat or hollow carbon density profiles in the core, and impurity confinement times consistently shorter than energy confinement times. Bayesian inferences of impurity transport coefficients based on laser blow-off injections and forward modeling via the Aurora package (Sciortino et al 2021 Plasma Phys. Control. Fusion 63 112001) show core cross-field diffusion to be higher in L-mode than in H-mode. Impurity profile shapes remain flat or hollow in all cases. Inferred radial profiles of diffusion and convection are compared to neoclassical, quasilinear gyrofluid, and nonlinear gyrokinetic simulations. Heat transport is observed to be better captured by reduced turbulence models with respect to particle transport. State-of-the-art gyrokinetic modeling compares favorably with measurements across multiple transport channels. Overall, these results suggest that diverted negative triangularity discharges may offer a path to a highly-radiative L-mode scenario with high core performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Novel internal measurements of ion cyclotron frequency range fast-ion driven modes

Abstract Novel internal measurements and analysis of ion cyclotron frequency range fast-ion driven modes in DIII-D are presented. Observations, including internal density fluctuation ( n ~ ) measurements obtained via Doppler backscattering, are presented for modes at low harmonics of the ion cyclotron frequency localized in the edge. The measurements indicate that these waves, identified as coherent ion cyclotron emission (ICE), have high wave number, k ⊥ ρ fast ≳ 1, consistent with the cyclotron harmonic wave branch of the magnetoacoustic cyclotron instability, or electrostatic instability mechanisms. Measurements show extended spatial structure (at least ∼1/6 the minor radius). These edge ICE modes undergo amplitude modulation correlated with edge localized modes (ELM) that is qualitatively consistent with expectations for ELM-induced fast-ion transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗