Search NASA⌕ Search

Engineering topics

Thompson, D.

Publications and source records attributed to Thompson, D..

33 records · Page 2

A search for quasar protoclusters at z greater than 4

In the CDM and many other hierarchical scenarios for the origins of large scale structure, the existence of luminous quasars at very high redshifts (z greater than 3 or 4) is difficult to understand, unless such objects form at the very highest peaks of the density field. One then might expect a strong clustering of quasars at large redshifts. This is a generic prediction for practically any reasonable primordial density fluctuation spectrum. For CDM, Efstathiou & Rees (1988) predicted that quasars at z greater than 4 should be clustered as strongly as the bright galaxies at z approx. than 0. Cole & Kaiser (1989) suggest that z greater than 4 quasars might represent greater than or approximately = 4(sigma) peaks of the density field and thus, should be clustered more strongly than galaxies at z approximately = 0. We are performing the following experiment: a search for quasars, AGN, or other discrete objects, e.g., starforming galaxies, near known, z greater than 4 quasars. In other words, use the early quasars as markers of possible protoclusters. This is a fairly basic test of our understanding of the formation of galaxies, large-scale structure, and the origin of the first quasars themselves.

Smith, J. D.↗

Parameterization of solar cells

The aggregation (sorting) of the individual solar cells into an array is commonly based on a single operating point on the current-voltage (I-V) characteristic curve. An alternative approach for cell performance prediction and cell screening is provided by modeling the cell using an equivalent electrical circuit, in which the parameters involved are related to the physical phenomena in the device. These analytical models may be represented by a double exponential I-V characteristic with seven parameters, by a double exponential model with five parameters, or by a single exponential equation with four or five parameters. In this article we address issues concerning methodologies for the determination of solar cell parameters based on measured data points of the I-V characteristic, and introduce a procedure for screening of solar cells for arrays. We show that common curve fitting techniques, e.g., least squares, may produce many combinations of parameter values while maintaining a good fit between the fitted and measured I-V characteristics of the cell. Therefore, techniques relying on curve fitting criteria alone cannot be directly used for cell parameterization. We propose a consistent procedure which takes into account the entire set of parameter values for a batch of cells. This procedure is based on a definition of a mean cell representing the batch, and takes into account the relative contribution of each parameter to the overall goodness of fit. The procedure is demonstrated on a batch of 50 silicon cells for Space Station Freedom.

Appelbaum, J.↗

Pulsed laser deposition of Tl-Ca-Ba-Cu-O films

Pulsed laser deposition is a technique commonly used to deposit high quality thin films of high temperature superconductors. This paper discusses the results obtained when this technique is applied to the deposition of Tl-Ca-Ba-Cu-O thin films using a frequency doubled Nd:YAG laser operating at 532 nm and an excimer laser operating at 248 nm. Films with onset temperatures of 125 K and zero resistance temperatures of 110 K deposited on (100) oriented MgO from a composite Tl2Ca2Ba2Cu3Ox target were obtained at both wavelengths upon appropriate post deposition annealing. Films deposited at 532 nm exhibit a rough surface, while those deposited at 248 nm are smooth and homogeneous. Upon annealing, films deposited at both wavelengths are single phase Tl2Ca2Ba2Cu3Ox.

Ianno, N. J.↗

Preparation of high T(c) Tl-Ba-Ca-Cu-O thin films by pulsed laser evaporation and Tl2O3 vapor processing

Tl-Ba-Ca-Cu-O superconducting thin films with zero-resistance temperatures up to 115 K have been prepared using a Tl2O3 vapor process on Ba-Ca-Cu-O precursor thin films. The Ba-Ca-Cu-O thin films were made by laser deposition on Y-stabilized ZrO2 substrates. This technique minimizes problems caused by the toxicity of Tl2O3, and its subsequent decomposition to the volatile and toxic Tl2O upon heating. Therefore, it may have practical application in the fabrication of high T(c) Tl-Ba-Ca-Cu-O superconducting thin-film devices.

Johs, B.↗

Highly oriented Tl2Ba2Ca2Cu3O10 thin films by pulsed laser evaporation

Superconducting thin films on MgO (100) substrates with nearly pure Tl2Ba2Ca2Cu3O10 (2:2:2:3) phase using pulsed laser evaporation and postannealing have been fabricated. The films had c axes perpendicular to the substrates. Superconducting films with onset temperatures of 125 K and zero resistance at 110 K were obtained. X-ray microprobe fluorescence measurements indicate that a typical composition of films is Tl(0.66)Ba(1.77)Ca(1.46)Cu3O(x) which is low in Tl compared to that expected for the 2:2:2:3 phase. A typical grain size is greater than 10 microns revealed by scanning electron microscopy.

Liou, S. H.↗

Development and validation of the crew-station system-integration research facility

The various issues associated with the use of integrated flight management systems in aircraft were discussed. To address these issues a fixed base integrated flight research (IFR) simulation of a helicopter was developed to support experiments that contribute to the understanding of design criteria for rotorcraft cockpits incorporating advanced integrated flight management systems. A validation experiment was conducted that demonstrates the main features of the facility and the capability to conduct crew/system integration research.

Nedell, B.↗

High-spatial-resolution studies of young stellar objects. II - A thick disk surrounding Lynds 1551, IRS 5

Heavily oversampled, small (2 arcsec) beam 2 micron maps of the region surrounding Lynds 1551, IRS 5 provide the basis for reconstructing maximum-entropy 'images' which have an effective spatial resolution of about 0.6 arcsec. These images reveal an extended, cusp-like structure surrounding IRS 5. This structure most likely results as light from IRS 5 is scattered in our direction by dust grains located in a thick disk of diameter 1000 AU. The disk is viewed nearly edge-on and has a mass in dust grains of 2 to 5 x 10 to the -5th solar masses. Its polar axis lies along the observed direction of the bipolar mass outflow inferred from molecular line observations of the L1551 cloud. It is possible that the observed infrared disk may represent the inner regions of a much larger thick-disk structure, whose shape derives from the combined effects of disk rotation and the gravitational field of IRS 5.

Strom, S. E.↗

High spatial resolution IR observations of young stellar objects - A possible disk surrounding HL Tauri

High spatial resolution images of the T Tauri star HL Tau were obtained at 1.6 microns and 2.2 microns. The original images as well as maximum entropy image reconstructions reveal a circumstellar envelope structure, similar at both wavelenghts, and extended along P.A. = 112 deg; the 10 percent width of the structure is 1.9 sec (300 AU at 160 pc). The extended structure is interpreted as light scattered toward earth by dust in a disk surrounding this young stellar object. Polarization measurements made at 2.2 microns support this hypothesis. The total solid particle mass is, at minimum, 5 x 10 to the -7th solar mass.

Grasdalen, G. L.↗

Agricultural applications of TM data

Multitemporal Thematic Mapper, Thematic Mapper Simulator, and detailed ground truth data were collected for a 9- by 11-km sample segment in Webster County, Iowa, in the summer of 1982. Three dates were acquired each with Thematic Mapper Simulator (June 7, June 23, and July 31) and Thematic Mapper (August 2, September 3, and October 21). The additional TM spectral bands in the middle infrared were found to substantially improve corn/soybean separability in both single date and multitemporal analyses.

Pitts, D. E.↗

Flame characteristics of a NASA contra swirler module

Results are presented for an investigation of the structure of unconfined propane flames stabilized on a NASA contra-swirl can. General flame characterization, flame visualization by sodium chloride, temperature measurements, combustion products analysis, nitric oxide concentrations, and laser anemometer studies are considered. The results are discussed relative to sodium chloride visualization, temperature distributions, chemical composition of flames, nitric oxide distributions, and velocity distributions. It is shown that unconfined propane-air flames can be stabilized downstream of a NASA contra-swirl can under a wide range of airflow rates and fuel-air ratios. However, on increasing fuel input from the lowest at which flames can be stabilized, a compact recirculation zone-stabilized flame is formed. The effect of confinement on changes in flame shape and structure is determined.

Thompson, D.↗

The effect of preheat on the structure of a swirl stabilized flame

The effect of preheat on the temperature and species distributions in propane flames stabilized on a NASA contraswirl can has been examined. Flames with compact stable structure, inner-swirler airflow of 0.0091 kg/s, outer-swirler-plus-bypass airflow of 0.0203 kg/s, and propane injected 1 mm upstream of the inner swirler hub have been selected for detailed study. Over the inlet-air-temperature range from 300 to 673 K the maximum temperature in the flame increased by 40 to 60 K per 100-K increase in inlet air temperature. The point of maximum temperature on the center line approached the exit plane as inlet air temperature was increased. Oxygen, CO, H2, and methane were found together in gas samples taken from the flame, including the regions of maximum flame temperature.

Thompson, D.↗

Flame characteristics of a NASA contra swirler module

The structure of unconfined flames stabilized on a NASA contra-swirl can has been examined. The structure depends on reference velocity and fuel-air ratio, and photographic illustrations of representative examples of each flame type are shown. A highly compact flame is obtained over a narrow band of fuel-air ratios, within the total range over which flames may be stabilized, at high reference velocity (27.8 m/s). The compact structure can only be obtained with careful fuel nozzle location. Chemical concentration profiles, temperature profiles and sodium chloride seeding experiments all confirm the visual impression of compactness. A flame with 50% greater fuel throughput has a much less compact structure, which is reflected in lower maximum temperature, much more complex chemical concentration distributions and a more diffuse recirculation boundary as observed by sodium chloride seeding than in the compact flame. Each of these flames has not only an evident axial recirculation core but also a toroidal recirculation region over the bluff region between the inner and outer swirlers. In contrast, laser Doppler velocimetry measurements carried out on a flame with lower reference velocity (5.65 m/s) do not indicate the presence of a secondary recirculation region in this flame.

Thompson, D.↗

Production of gamma rays with energies greater than 30 MeV in the atmosphere

A three-dimensional study of atmospheric gamma rays with energy greater than 30 MeV has been carried out. Experimental results were obtained from four balloon flights from Palestine, Texas, with a 15 cm by 15 cm digitized wire grid spark chamber. The energy spectrum for downward-moving gamma rays steepens with increasing atmospheric depth. Near the top of the atmosphere, the spectrum steepens with increasing zenith angle. Experimental results compare reasonably well with a three-dimensional Monte Carlo calculation of atmospheric gamma ray production. Inclusion of upward-moving gamma rays makes possible the use of atmospheric secondaries for in-flight calibration of satellite gamma ray detectors.

Thompson, D.↗