Engineering topics
Timmerman, Paul
Publications and source records attributed to Timmerman, Paul.
Electric Propulsion System Selection Process for Interplanetary Missions
The disparate design problems of selecting an electric propulsion system, launch vehicle, and flight time all have a significant impact on the cost and robustness of a mission. The effects of these system choices combine into a single optimization of the total mission cost, where the design constraint is a required spacecraft neutral (non-electric propulsion) mass. Cost-optimal systems are designed for a range of mass margins to examine how the optimal design varies with mass growth. The resulting cost-optimal designs are compared with results generated via mass optimization methods. Additional optimizations with continuous system parameters address the impact on mission cost due to discrete sets of launch vehicle, power, and specific impulse. The examined mission set comprises a near-Earth asteroid sample return, multiple main belt asteroid rendezvous, comet rendezvous, comet sample return, and a mission to Saturn.
Analysis of System Margins on Missions Utilizing Solar Electric Propulsion
NASA's Jet Propulsion Laboratory has conducted a study focused on the analysis of appropriate margins for deep space missions using solar electric propulsion (SEP). The purpose of this study is to understand the links between disparate system margins (power, mass, thermal, etc.) and their impact on overall mission performance and robustness. It is determined that the various sources of uncertainty and risk associated with electric propulsion mission design can be summarized into three relatively independent parameters 1) EP Power Margin, 2) Propellant Margin and 3) Duty Cycle Margin. The overall relationship between these parameters and other major sources of uncertainty is presented. A detailed trajectory analysis is conducted to examine the impact that various assumptions related to power, duty cycle, destination, and thruster performance including missed thrust periods have on overall performance. Recommendations are presented for system margins for deep space missions utilizing solar electric propulsion.
Spin-Stabilized Microsatellites with Solar Concentrators
A document proposes the development of spin-stabilized microsatellites powered by solar photovoltaic cells aided by solar concentrators. Each such satellite would have a cylindrical or other axisymmetric main body with solar cells mounted in a circumferential belt-like array on its exterior surface. The solar concentrator would be a halo-like outrigger cylindrical Fresnel lens array that would be deployed from and would surround the main body, connected to the main body via spokes or similar structural members. The spacecraft would be oriented with its axis of symmetry perpendicular to the line of sight to the Sun and would be set into rotation about this axis. In effect, the solar cells and concentrator would be oriented and rotated in a "rotisserie" mode, making it possible to take advantage of the concentration of solar light while preventing localized overheating of the solar cells. In addition, the mechanical stabilization inherently afforded by the rotation could be exploited as a means of passive attitude control or, at least, of reducing the requirement for active attitude control.
High Power, High Voltage Electric Power System for Electric Propulsion
This paper provides an overview of the 30 KW, 600 V MRHE power subsystem. Descriptions of the power subsystem elements, the mode of power transfer, and power and mass estimates are presented. A direct-drive architecture for electric propulsion is considered which reduces mass and complexity. Solar arrays with concentrators are used for increased efficiency. Finally, the challenges due to the environment of a hypothetical lunar mission as well as due to the advanced technologies considered are outlined.
Improved Control of Charging Voltage for Li-Ion Battery
The protocol for charging a lithium-ion battery would be modified, according to a proposal, to compensate for the internal voltage drop (charging current internal resistance of the battery). The essence of the modification is to provide for measurement of the internal voltage drop and to increase the terminal-voltage setting by the amount of the internal voltage drop. Ordinarily, a lithium-ion battery is charged at constant current until its terminal voltage attains a set value equal to the nominal full-charge potential. The set value is chosen carefully so as not to exceed the lithium-plating potential, because plated lithium in metallic form constitutes a hazard. When the battery is charged at low temperature, the internal voltage drop is considerable because the electrical conductivity of the battery electrolyte is low at low temperature. Charging the battery at high current at any temperature also gives rise to a high internal voltage drop. In some cases, the internal voltage drop can be as high as 1 volt per cell. Because the voltage available for charging is less than the terminal voltage by the amount of the internal voltage drop, the battery is not fully charged (see figure), even when the terminal voltage reaches the set value. In the modified protocol, the charging current would be periodically interrupted so that the zero-current battery-terminal voltage indicative of the state of charge could be measured. The terminal voltage would also be measured at full charging current. The difference between the full-current and zero-current voltages would equal the internal voltage drop. The set value of terminal voltage would then be increased beyond the nominal full-charge potential by the amount of the internal voltage drop. This adjustment would be performed repeatedly, in real time, so that the voltage setting would track variations in the internal voltage drop to afford full charge without risk of lithium plating. If the charging current and voltage settings were controlled by a computer, then this method of charge control could readily be implemented in software.
The year in review : power systems in space exploration
Explore the source record for details and available documents.
Application of First Principles Ni-Cd and Ni-H2 Battery Models to Spacecraft Operations
The conclusions of the application of first principles model to spacecraft operations are: the first principles of Bi-phasic electrode presented model provides an explanation for many behaviors on voltage fading on LEO cycling.
Application of First Principles Model to Spacecraft Operations
Previous models use a single phase reaction; cycled cell predicts cannot be met with a single phase; interphase conversion provides means for film aging; aging cells predictions display typical behaviors: pressure changes in NiH² cells; voltage fading upon cycling; second plateau on discharge of cycled cells; negative limited behavior for Ni-Cds.
Electrical characterization of the Magellan batteries after storage
Two 22 cell batteries designed by Martin Marietta were tested. The batteries were rated at 26.5 Amp-Hr. The battery design is characterized by the following: Gates Aerospace 42B030AB15, 11 pos/12 neg, Pellon 2536 separator, passivated pos/teflonated neg. The tests can be summarized as follows: (1) no noticeable capacity loss after storage period; and (2) batteries exhibited larger non-uniformity of cell voltages during constant current charge.
The JPL/NASA/TAMU nickel-cadmium battery model development status
A discussion of the development of a fundamental cell model is presented in vugraph format. The nickel oxide layer is described in terms of the electronic conductivity of the oxide layer and proton diffusion through the oxide layer. The kinetic and conductivity expressions for the cadmium electrode were improved. The development process yielded performance predictions that are significantly improved.