Engineering topics

Tipireddy, Ramakrishna

Publications and source records attributed to Tipireddy, Ramakrishna.

7 records

DOE OSTI2023

Accelerating Scientific Simulations with Bi-Fidelity Weighted Transfer Learning

High-fidelity modeling is an essential design tool for many engineering applications. However, for complex systems, computational cost can be a limiting factor. Analyzing parameter sensitivity, uncertainty quantification, and design optimization require many model evaluations. Surrogate models are often used to develop the relationship between model parameters and quantities of interest. However, in the case of complex systems, surrogate models require several degrees of freedom and, thus, a large number of data points to determine the correct dependencies. For many applications, this may be prohibitively expensive. The reduction of computational requirements can be achieved by leveraging low-fidelity models. Low-fidelity models represent the system at a coarser resolution with the advantage of computational efficiency. Therefore, a bi-fidelity modeling paradigm, which augments the accuracy of a low-fidelity model in a computationally efficient manner by invoking limited runs of a high-fidelity model, can be leveraged to sufficiently balance the accuracy and computational requirements. In this work, a bi-fidelity weighted transfer learning method using neural networks was applied to a computational fluid dynamics heat transfer modeling problem. The transfer learning advantage was investigated as a function of hyperparameters. Our main finding is that the use of a bi-fidelity modeling paradigm achieves accuracy close to that of a high-fidelity Gaussian process model while significantly reducing computational cost. The bi-fidelity model achieves comparable performance with 90 high-fidelity samples-that is, 60% less than the samples needed to achieve similar accuracy without the use of bi-fidelity modeling,

Borowiec, Katarzyna↗

DOE OSTI2023

Conditional Karhunen–Loève regression model with Basis Adaptation for high-dimensional problems: Uncertainty quantification and inverse modeling

Here, we propose a methodology for improving the accuracy of surrogate models of the observable response of physical systems as a function of the systems’ spatially heterogeneous parameter fields, with applications to uncertainty quantification and parameter estimation in high-dimensional problems. Practitioners often formulate finite-dimensional representations of spatially heterogeneous parameter fields using truncated unconditional Karhunen–Loève expansions (KLEs) for a certain choice of unconditional covariance kernel and construct surrogate models of the observable response with respect to the KLE coefficients. When direct measurements of the parameter fields are available, we propose improving the accuracy of these surrogate models by representing the parameter fields via conditional Karhunen-Loève expansions (CKLEs). CKLEs are constructed by conditioning the covariance kernel of the unconditional expansion on the direct measurements of the parameter field via Gaussian process regression, and then truncating the corresponding KLE. We apply the proposed methodology to constructing surrogate models via the Basis Adaptation (BA) method of the stationary hydraulic head response, measured at spatially discrete observation locations, of a groundwater flow model of the Hanford Site, as a function of the 1000-dimensional representation of the model’s log-transmissivity field. We find that BA surrogate models of the hydraulic head based on CKLEs are more accurate than BA surrogate models based on unconditional expansions for forward uncertainty quantification tasks. Furthermore, we find that inverse estimates of the hydraulic transmissivity field computed using CKLE-based BA surrogate models are more accurate than those computed using unconditional BA surrogate models.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Extending Conformal Prediction to Hidden Markov Models with Exact Validity via de Finetti’s Theorem for Markov Chains

Conformal prediction is a widely used method to quantify uncertainty in settings where the data is independent and identically distributed (IID), or more generally, exchangeable. Conformal prediction takes in a pre-trained classifier and a calibration dataset as inputs, and returns a function which maps feature vectors to subsets of classes. The output of the returned function for a new feature vector is guaranteed to contain the true class with a pre-specified confidence. Despite its success and usefulness in IID settings, extending conformal prediction to non-exchangeable (e.g., Markovian) data in a manner that provably preserves all desirable theoretical properties has largely remained an open problem. As a solution, we extend conformal prediction to the setting of a Hidden Markov Model (HMM) with unknown parameters. The key idea behind the proposed method is to partition the non-exchangeable Markovian data from the HMM into exchangeable blocks by exploiting the de Finetti’s Theorem for Markov Chains discovered by Diaconis and Freedman (1980). The permutations of the exchangeable blocks are then viewed as randomizations of the observed Markovian data from the HMM. The proposed method provably retains all desirable theoretical guarantees offered by the classical conformal prediction framework and is general enough to be useful in many sequential prediction problems.

Nettasinghe, Don Buddhika Wijayantha↗

DOE OSTI2022

Uncertainty Quantification Framework for Predicting Material Response with Large Number of Parameters: Application to Creep Prediction in Ferritic-Martensitic Steels Using Combined Crystal Plasticity and Grain Boundary Models

This paper presents an uncertainty quantification (UQ) framework for the physics-based model prediction of material response with a large number of parameters. The application problem presented in this work is that of predicting creep in Grade 91 steel at 600°C. The material response is defined with a physically based microstructural model with constitutive equations emulating several observed phenomena in Grade 91 and embodied into an explicit geometry mesoscale finite element model for prior austenite grains and grain boundaries. Creep within the grains and in grain boundaries are represented by crystal plasticity for dislocation motion and a physics-based model for cavity growth and nucleation, respectively. The creep behavior of this material is influenced by several parameters, some of which have a wide range of variation based on experimental data. UQ combined with microstructural modeling can discover the core microstructural causes of experimental variability, leading to improved materials with lower variability in critical long-term material properties. In this study, we investigate the model's uncertainty to identify material properties that may be modified during production to increase creep life and analyze different components of the crystal plasticity model for improvements. For this purpose, a quantity of interest is defined as time to minimum creep rate, which correlates well to the creep failure of the material. A deep neural network model was trained and validated to be used as a surrogate for the finite element model. Then, a variance-based sensitivity analysis is performed on the surrogate model to find the Sobol indices of the input parameters in respect to the output quantity of interest. The Sobol indices are used to reduce the dimensionality of the model. Generalized polynomial chaos expansion is used on the reduced basis models to propagate the uncertainty from the input parameters to the quantity of interest using the deep neural network surrogate model. These results are benchmarked against uncertainty propagation using Monte Carlo simulations. In conclusion, the UQ performed through the reduced basis model captures almost all the uncertainty in the model with significantly fewer simulations, making it possible to perform the UQ directly via simulations with the finite element model rather than surrogate machine-learned models.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Physics-Informed Gaussian Process Regression for States Estimation and Forecasting in Power Grids

Real-time state estimation and forecasting are critical for the efficient operation of power grids. In this paper, a physics-informed Gaussian process regression (PhI-GPR) method is presented and used for forecasting and estimating the phase angle, angular speed, and wind mechanical power of a three-generator power grid system using sparse measurements. In standard data-driven Gaussian process regression (GPR), parameterized models for the prior statistics are fit by maximizing the marginal likelihood of observed data. In the PhI-GPR method, we propose to compute the prior statistics offline by solving stochastic differential equations (SDEs) governing the power grid dynamics. The short-term forecast of a power grid system dominated by wind generation is complicated by the stochastic nature of the wind and the resulting uncertainty in wind mechanical power. Here, we assume that the power grid dynamics are governed by swing equations, with the wind mechanical power fluctuating randomly in time. We solve these equations for the mean and covariances of the power grid states using the Monte Carlo simulation method. We demonstrate that the proposed PhI-GPR method can accurately forecast and estimate observed and unobserved states. For the considered problem, PhI-GPR has computational advantages over the ensemble Kalman filter (EnKF) method: In PhI-GPR, ensembles are computed offline and independently of the data acquisition process, whereas for EnFK, ensembles are computed online with data acquisition, rendering real-time forecast more challenging. We also demonstrate that the PhI-GPR forecast is more accurate than the EnKF forecast when the random mechanical wind power is non-Markovian. In contrast, the two methods produce similar forecasts for the Markovian mechanical wind power. For observed states, we show that PhI-GPR provides a forecast comparable to the standard data-driven GPR; both forecasts are significantly more accurate than the autoregressive integrated moving average (ARIMA) forecast. We also show that the ARIMA forecast is more sensitive to observation frequency and measurement errors than the PhI-GPR forecast.

24 POWER TRANSMISSION AND DISTRIBUTION↗

DOE OSTI2022

Sequential Decision Making (SDM) for Mesh Refinement and Model Selection in Multiscale, Multi-Physics Applications

Intelligent automation and decision support are needed to enhance computational efficiency and robustness in multiscale and multi-physics problems, including materials science, manufacturing, and climate and weather modeling. Current scientific computing approaches for enabling decisions by scientists fail to explore the role of learning, reasoning, and probabilistic planning. Often these decisions are not performed in real-time during the computation but are made prior to the start of the computation, which must be interrupted in order to make changes to the prior choices. Such interruptions at different stages of the computation increase the total computing time and the need for a human expert to frequently monitor the results. State of art scientific computing methods consist of rule-based algorithms that cannot automatically adapt to a dynamically changing computing environment. The development of a Sequential Decision Making (SDM) framework will automate scientific computing by optimizing the policies for mesh refinement, time-stepping, model and algorithm selection, resource allocation, and pre and post-processing. Our agent SDM framework for scientific computing will consist of data-driven learning (Classifier), automated reasoning (contextual knowledge), and probabilistic planning (Reinforcement Learning). In this project, we focused on three problems to demonstrate our SDM framework on a set of ordinary and partial differential equations. Classification of Lorenz system regions using Feed-Forward Neural Networks examined learning in the SDM framework. On the other hand, reasoning and planning in the SDM framework were used in two problems: adaptive time-stepping for nonlinear ODEs using on-policy RL algorithms, and adaptive mesh refinement for 2-D PDEs using off-policy RL algorithms.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2022

MULTISTEP AND CONTINUOUS PHYSICS-INFORMED NEURAL NETWORK METHODS FOR LEARNING GOVERNING EQUATIONS AND CONSTITUTIVE RELATIONS

In this work, we investigate the applicability and relative merit of discrete and continuous versions of physics-informed neural network (PINN) methods for learning unknown governing equations or constitutive relations in a nonlinear dynamical system. In the case of unknown dynamics, entire right-hand-side (RHS) equations of the ordinary differential equations are unknown. In the case of unknown constitutive relations, however, the RHS equations are known up to the specification of constitutive relations (that may depend on the state of the system). We use a deep neural network to model unknown governing equations or constitutive relations. The discrete PINN approach combines classical multistep discretization methods for dynamical systems with neural-network-based machine learning methods. On the other hand, the continuous versions utilize deep neural networks to minimize the residual function for the continuous governing equations. We use the case of a fedbatch bioreactor system to study the effectiveness of these approaches and discuss conditions for their applicability. Our results indicate that the accuracy of the trained neural network models is much higher for the cases where we only have to learn a constitutive relation instead of all dynamics. This finding corroborates the well-known fact from scientific computing that building as much structural information as is available into an algorithm can enhance its efficiency and/or accuracy.

97 MATHEMATICS AND COMPUTING↗