Search NASA⌕ Search

Engineering topics

Tjiptowidjojo, Kristianto

Publications and source records attributed to Tjiptowidjojo, Kristianto.

Experimental and computational design tools for industrial drying processes: Challenges in process‐limit prediction

Abstract The coating and drying of inks and slurries are important steps to manufacture a plethora of products. Drying processes, particularly, comprise energy‐intensive steps that affect product cost and quality. Prior work has highlighted failures of various multicomponent diffusivity models to conserve mass in dryer modeling and challenges in predicting process limits given variability in published values of key thermodynamic parameters. Herein, we develop a computational model and benchtop drying experiments to investigate these concerns for drying polymer‐laden coatings. Model predictions of process limits in a single‐zone drying oven demonstrate that published variability in Flory–Huggins parameter yields large variations in predicted operating temperatures above which blistering occurs. This indicates that caution should be exercised when choosing approaches to obtain or predict the Flory–Huggins parameter, and that both benchtop drying experiments and a set of additional experiments, such as sorption experiments, are needed to fully characterize and optimize a given drying process.

Parrish, Chance↗

A level set approach for the computational study of a yield stress fluid filling a thin mold

Many important engineering and scientific applications such as cement slurries, foams, crude oil, and granular avalanches involve the concept of yield stress. Therefore, modeling yield stress fluids in different flow configurations, including the accurate prediction of the yield surface, is important. In this paper, we present a computational model based on the finite element method to study the flow of yield stress fluids in a thin mold and compare the results with data from flow visualization experiments. Here, we use the level set method to describe the interface between the filling fluid and air. We use polypropylene glycol as a model Newtonian fluid and Carbopol for the model yield stress fluid, as the Carbopol solution demonstrates yielding without thixotropy. To describe the yielding and shear-thinning behavior, we use a generalized Newtonian constitutive equation with a Bingham–Carreau–Yasuda form. We compare the results obtained from the mold filling experiments with the results from the three-dimensional (3D) model and from a reduced-order Hele-Shaw (HS) model that is two-dimensional, including the effect of shear-thinning along the thin direction only approximately. We show that both the 3D and the HS model can capture the experimental meniscus shape reasonably well for all the fluids considered at three different flow rates. This indicates that the shape evolution is insensitive to the dimensionality of the model. However, the viscosity and yield surfaces predicted by the 3D and HS models are different. The HS model underestimates the high viscosity and unyielded regions compared to the estimation by the 3D model.

42 ENGINEERING↗

Slot-die-coating operability windows for polymer electrolyte membrane fuel cell cathode catalyst layers

Roll-to-roll (R2R) slot-die coating of polymer electrolyte membrane fuel cell (PEMFC) catalyst layers represents a scalable deposition method for producing 10–20 m 2 ·min -1 of catalyst-coated gas diffusion layers (GDLs). This high-throughput production technique will help lower the cost of PEMFC catalyst layers. The uniformity of the wet layer applied by slot die deposition is affected by process parameters such as substrate speed, vacuum pressure applied at the upstream meniscus, gap between the slot die lips and substrate, ink rheology, and other ink and substrate properties. The set of conditions for producing a defect-free coating with a dilute ink typically requires little to no upstream vacuum pressure, so suitable operating conditions can be found easily through trial and error and operator intuition. However, the higher viscosity of more concentrated inks dramatically shifts the range of settings that result in a homogeneous coating to higher vacuum levels, which are harder to find through hit or miss. A predictive model showing the range of operable conditions decreases material wastage inherent in experimentally searching for suitable parameters. In this study, the defect-free coating parameter window is explored experimentally and theoretically for two concentrations of PEFC cathode inks. Both a full capillary hydrodynamic model and a computationally cheaper viscocapillary model successfully predict the experimentally determined coating window within the experimental and model uncertainty limits for inks with 5.3 wt% and 12.0 wt% solids ink while maintaining the 0.1 mg Pt ·cm -2 Pt areal loading target. Here, this paper demonstrates a viable pathway for meeting the $30/kW net ultimate cost target of the United States Department of Energy (U.S. DOE) Hydrogen Fuel Cells Technologies Office (HFTO). The concentrated ink lowers the thermal energy and capital expenditure (CapEx) budget of the coating process by decreasing the amount of time, energy, and floorspace required for drying the coating.

25 ENERGY STORAGE↗

Process model for multilayer slide coating of polymer electrolyte membrane fuel cells

Slide coating is a precision method suitable for depositing multiple liquid-film layers simultaneously. Originally developed in the photographic film industry, it has been deployed for manufacturing of other products that benefit from multilayer coatings. One emerging application is the manufacture of polymer electrolyte membrane fuel cells (PEMFCs), which are used to produce electricity through electrochemical reactions of hydrogen and oxygen gas. The membrane-electrode assembly (MEA), in which key electrochemical reactions occur, consists of three layers that are typically deposited separately in serial fashion and then laminated together to form the three-layer MEA, i.e., three sequential steps of coat and dry. Adapting the process to simultaneous, multilayer slide coating of all three layers will save equipment cost and space while minimizing possible exposure to contaminants during transition between the steps. We are developing a three-layer slide coating model to aid the manufacturing process design of PEMFC. The model accounts for rheology of each layer, which typically exhibit shear thinning behavior. Model predictions are used to investigate simultaneous coatability of catalyst inks and to determine the best layer-by-layer ink selection.

25 ENERGY STORAGE↗

An Experimental Investigation of Multilayer Flow in a Slide Die Coating Process

Roll-to-roll coating technology has been actively applied not only for conventional film production but also for emerging energy devices such as organic solar cells, organic light emitting diodes, batteries, smart windows, and fuel cells. The devices are multilayer structures requiring several coating and drying steps when implemented in a serial fashion, which increases capital costs and energy consumption. Simultaneous multilayer (ML) coating technologies present an opportunity for cost reductions and improved process efficiency by reducing equipment footprint and the number of process steps. In this talk, we experimentally investigate ML slide die coating flow for the manufacturing of fuel cell membrane electrode assemblies (MEAs). For ML slide coating, understanding fluid properties such as density, surface tension, and viscosity are necessary for stable flows and limiting intermixing of the miscible layers. Here, we utilize a design-of-experiment methodology - Box-Behnken design (BBD) - to correlate ink formulation parameters to fluid properties. Using the ink properties obtained from the BBD, we performed numerical flow simulations to obtain a proper process conditions to guide experimental coating trials. Finally, experimental verification is performed on a ML slide die and a degree of miscibility was observed for various ink formulation conditions.

28 EE - Advanced Manufacturing Office (EE-5A)↗

Elastohydrodynamics of roll-to-roll UV-cure imprint lithography

Inextensible cylindrical shell theory and lubrication theory combine into a model for the elastohydrodynamics of a rolling-imprint modality of nanoimprint lithography (NIL). Foil-bearing theory describes the formation of the lubrication gap due to relative motion between a tensioned substrate and a rigid, cylindrical surface. Reproduction of the results of foil-bearing theory for both stiff and perfectly-flexible substrates validates this coupled model and reveals a highly predictable region of uniformity that provides low shear stress conditions ideal for UV-cure. Here, these results show theoretical limitations that are used to construct an operating window for predicting rolling-mode NIL process feasibility.

42 ENGINEERING↗

Finite element simulations of viscoelastic flow of blade coating using the log-conformation tensor

Previous studies have demonstrated the benefits of the log-conformation formulation to model viscoelastic fluids; it increases stability at high Weissenberg numbers and ensures that the conformation tensor remains positive-definite. Many studies have applied the log-conformation tensor formulation to benchmark cases; however, relatively few studies investigate using the formulation on more complex flows. In this paper, we extend the log-conformation formulation to the manufacturing-relevant flow of blade coating. We first verify the log-conformation formulation on the benchmark problem of flow past a cylinder using the finite element method, and then apply it to the blade-coating process, in which a viscoelastic fluid entrained by a moving substrate passes under a blade at a constant web speed. We investigate various rheological effects and the resulting film thickness for the blade-coating problem, and compare the results from the log-conformation formulation to those of the original stress formulation. To this end, we show that the log-conformation formulation agrees well with other established methods, and also increases the maximum achievable web speed in the blade-coating problem.

36 MATERIALS SCIENCE↗

A computational model for doctoring fluid films in gravure printing

The wiping, or doctoring, process in gravure printing presents a fundamental barrier to resolving the micron-sized features desired in printed electronics applications. This barrier starts with the residual fluid film left behind after wiping, and its importance grows as feature sizes are reduced, especially as the feature size approaches the thickness of the residual fluid film. In this work, various mechanical complexities are considered in a computational model developed to predict the residual fluid film thickness. Lubrication models alone are inadequate, and deformation of the doctor blade body together with elastohydrodynamic lubrication must be considered to make the model predictive of experimental trends. Moreover, model results demonstrate that the particular form of the wetted region of the blade has a significant impact on the model's ability to reproduce experimental measurements.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanomanufacturing: Nano-Structured Materials Made Layer-by-Layer

Large-scale, high-throughput production of nano-structured materials (i.e. nanomanufacturing) is a strategic area in manufacturing, with markets projected to exceed $\$$1T by 2015. Nanomanufacturing is still in its infancy; process/product developments are costly and only touch on potential opportunities enabled by growing nanoscience discoveries. The greatest promise for high-volume manufacturing lies in age-old coating and imprinting operations. For materials with tailored nm-scale structure, imprinting/embossing must be achieved at high speeds (roll-to-roll) and/or over large areas (batch operation) with feature sizes less than 100 nm. Dispersion coatings with nanoparticles can also tailor structure through self- or directed-assembly. Layering films structured with these processes have tremendous potential for efficient manufacturing of microelectronics, photovoltaics and other topical nano-structured devices. This project is designed to perform the requisite R and D to bring Sandia's technology base in computational mechanics to bear on this scale-up problem. Project focus is enforced by addressing a promising imprinting process currently being commercialized.

36 MATERIALS SCIENCE↗

Dynamics of discontinuous coating and drying of nanoparticulate films.

Heightened interest in micro-scale and nano-scale patterning by imprinting, embossing, and nano-particulate suspension coating stems from a recent surge in development of higher-throughput manufacturing methods for integrated devices. Energy-applications addressing alternative, renewable energy sources offer many examples of the need for improved manufacturing technology for micro and nano-structured films. In this presentation we address one approach to micro- and nano-pattering coating using film deposition and differential wetting of nanoparticles suspensions. Rather than print nanoparticle or colloidal inks in discontinuous patches, which typically employs ink jet printing technology, patterns can be formed with controlled dewetting of a continuously coated film. Here we report the dynamics of a volatile organic solvent laden with nanoparticles dispensed on the surfaces of water droplets, whose contact angles (surface energy) and perimeters are defined by lithographic patterning of initially (super)hydrophobic surfaces.. The lubrication flow equation together with averaged particle transport equation are employed to predict the film thickness and particle average concentration profiles during subsequent drying of the organic and water solvents. The predictions are validated by contact angle measurements, in situ grazing incidence small angle x-ray scattering experiments, and TEM images of the final nanoparticle assemblies.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗