Engineering topics
Publications and source records attributed to To, Anh.
Cu/BEA was synthesized via incipient wetness impregnation with Cu(NO)3-2.5H2O to achieve 5 wt.% Cu loading. Bronsted acid sites were quantified with isopropylamine temperature programmed desorption.
The conversion of lignocellulosic-derived carbon sources via the creation of a CO2 rich syngas stream provides means to produce liquid hydrocarbon fuels, with advancements intended to create a cost-competitive method of sequential conversion via methanol and dimethyl ether intermediates. Previously developed methods with Cu/Beta zeolites enabled the conversion of dimethyl ether to linear and branched hydrocarbons, with high selectivities towards products with high-octane fuel properties. Through process intensification, use of a single reactor to convert syngas to methanol and DME, then further to hydrocarbons, allows for reduced capitol and operation cost for the same chemistries that typically use 3 reactors instead of one. Utilization of commercially available methanol synthesis catalyst (Megamax 800, Clariant, CZA) and methanol dehydration catalyst with the Cu/Beta catalyst allowed for conversion into hydrocarbon products in this single reactor set up. Reactor configuration with CZA and alumina catalysts mixed with or stacked in a bed physically above the Cu/Beta catalyst provided a system for the direct conversion of the syngas to hydrocarbons with improved yields and selectivities with higher net C1 conversions for stacked bed configurations. Through control of the process conditions, greater conversion of C1 oxygenate intermediates (i.e., methanol and dimethyl ether) was achieved with concomitant increase in selectivities towards gasoline and jet fuel range olefin and paraffin products. Lower hydrocarbon number products and less naphthenes were observed for the conversion of syngas compared to DME conversion on only the Cu/Beta system with prominent selectivities observed for C4, C5, and C7 hydrocarbons. The DME and methanol formation rates, with understanding of the equilibria for both processes, were determined as important factors to allow for improved performance of the Cu/Beta. Determination of the factors which allow for tuning of selectivities and yields created an intensified process which allows for a "market-responsive" biorefinery design, which can produce high octane gasoline or jet fuel range hydrocarbons to meet demands for a more sustainable route to liquid fuels.
The paraffin-to-olefin (P/O) ratio in gasoline fuel is a critical metric affecting fuel properties and engine efficiency. In the conversion of dimethyl ether (DME) to high-octane hydrocarbons over BEA zeolite catalysts, the P/O ratio can be controlled through catalyst design. Here, we report bimetallic catalysts that balance the net hydrogenation and dehydrogenation activity during DME homologation. The Cu-Zn/BEA catalyst exhibited greater relative dehydrogenation activity attributed to higher ionic site density, resulting in a lower P/O ratio (6.6) versus the benchmark Cu/BEA (9.4). The Cu-Ni/BEA catalyst exhibited increased hydrogenation due to reduced Ni species, resulting in a higher P/O ratio (19). The product fuel properties were estimated with an efficiency merit function and compared against finished gasolines and a typical alkylate blendstock. Merit values for the hydrocarbon product from all three BEA catalysts exceeded those of the comparison fuels (0–5.3), with the product from Cu-Zn/BEA exhibiting the highest merit value (9.7).
Grindelia squarrosa (curlycup gumweed) biomass possesses unique biochemistry, cell wall composition, and leaf architecture tailored for prolific growth in arid and semiarid climates. Most notably, this plant has developed high levels of extractable resins that have high effective H/C eff ratios ((mol H - 2 x mol O)/mol C), which is hypothesized to lead to low coke formation during catalytic fast pyrolysis (CFP) over the ZSM-5 catalyst. In microscale experiments with high ZSM-5 loadings (biomass-to-catalyst mass ratio (B/C) ~ 0.1), in situ CFP generated high yields of aromatic hydrocarbons (30% carbon yield) while ex situ CFP favored aliphatic hydrocarbons (25% carbon yield). The difference between the two configurations was attributed to the constant catalyst temperature during ex situ CFP. Deactivation leading to partially deoxygenated vapor products occurred rapidly until B/C ≤ 0.5 by the adsorption of organic species blocking access to acid sites inside the micropores of the catalyst. This was followed by more gradual deactivation leading to primary vapor breakthrough, which we attribute to coke formation on acid sites on the external surface of ZSM-5 crystallites. Noncatalytic fast pyrolysis of Grindelia in a bench scale reactor produced oils with oxygen content (18 wt % on dry basis) and carbon yield (33%) comparable to those of CFP of woody biomass. The CFP of Grindelia further reduced the oxygen content to 7 wt % for in situ CFP and 4 wt % for ex situ CFP at B/C of 2-3. The good deoxygenation was attributed to a combination of a high H/C eff ratio and overall better quality of the pyrolysis vapors that were passed over the ZSM-5 catalyst. The high inorganic content of the Grindelia likely catalyzed pyrolysis to remove oxygenated coke precursors. This integrated CFP study demonstrated that Grindelia could be an important feedstock for generating stabilized noncatalytic and CFP oils for downstream processing into fuels and/or extraction of high-value chemicals. The preprocessing of this feedstock will be required to remove inorganics, which cause an irreversible deactivation of ZSM-5.