Engineering topics

Todd R White

Publications and source records attributed to Todd R White.

10 records

NASA NTRS2022

Mars Entry Instrumentation Flight Data and Mars 2020 Entry Environments

On February 18th, 2021, the Mars 2020 entry vehicle delivered the Perseverance rover to the surface of Mars. The entry vehicle carried a set of instrumentation installed on the heatshield and backshell to measure aerodynamic and aerothermal performance, named the Mars Entry, Descent, and Landing Instrumentation 2. This set of instrumentation included pressure transducers, thermocouples, heatflux sensors, and a radiometer, as well as a dedicated sensor support electronics system. All MEDLI2 hardware operated as expected during cruise and entry. MEDLI2 sensors gathered accurate pressure measurements in hypersonic through supersonic regimes to reconstruct vehicle attitude and atmospheric profiles. MEDLI2 on the heatshield sensors indicated that surface temperatures, caused by turbulent heating beginning 70 seconds after entry, remained at or below 1430 °C, while heatshield bondline temperatures rose less than 45 °C. Backshell surface TPS temperatures peaked at 630 °C, which was caused primarily by radiative heating measured by several separate sensors. The MEDLI2 temperature and pressure measurements enabled further detailed characterization of the Mars 2020 entry performance, and the flight dataset will provide a wealth of information for the EDL community and future mission designers.

thermal protection system↗

NASA NTRSDate not supplied

Data Fusion of In-Flight Aerothermodynamic Heating Measurements Using Kalman Filtering

On February 18th, 2021, the Mars 2020 entry system successfully delivered the Perserverance rover to the surface of Mars at Jezero Crater. The entry capsule carried a set of instrumentation installed on the heat shield and backshell, named the Mars 2020 Entry, Descent, and Landing Instrumentation. The instruments include pressure transducers, thermocouples, heat flux gauges, and radiometers to measure the aerodynamic and aerothermodynamic performance of the entry vehicle. Three of these sensors, a thermocouple plug, heat flux gauge, and a radiometer, are located in close proximity on the backshell. Each sensor is exposed to roughly the same environment, but measured these environments in different ways, each with its own set of modeling and measurement error complications. This paper develops a method for blending each of these measurements together in a single algorithm to produce estimates of the aerothermodynamic environments at that location on the backshell. The approach makes use of the Kalman filter methodology for solving state estimation problems. The filter has a predictor/corrector structure in which simplified process models are used to propagate the aeroheating states forward through time, which are then updated based on the measurement data. The method has been tested on simulated datasets.

Christopher D. Karlgaard↗

NASA NTRSDate not supplied

Inverse Estimation of Mars 2020 Entry Aeroheating Environments Using MEDLI2 Flight Data

The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite collected heating and pressure data during entry into Mars' atmosphere of the Mars 2020 Perseverance rover. MEDLI2 included thermocouples, heat flux sensors, and pressure transducers on both the heatshield and the backshell. This paper covers the inverse estimation of heatshield and backshell surface heating based on the MEDLI2 Instrumented Sensor Plugs (MISPs), a network of thermocouples embedded in thermal protection system plugs across the aeroshell. Monte Carlo analysis was conducted to assess the sensitivity of the surface heat rate and temperature to uncertainties in thermocouple depth and material properties such as density, specific heat capacity, and thermal conductivity. Data from each MISP was also used to estimate the local time of transition from laminar to turbulent flow at each plug location.

Hannah S Alpert↗

NASA NTRSDate not supplied

MEDLI2 Material Response Model Development and Validation

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating and temperatures. Discrepancies between MEDLI’s recorded in-depth heating data and the predicted thermal response and recession led to a campaign to characterize and test Mars Entry, Descent, and Landing Instrument 2 (MEDLI2) flight lot thermal protection materials (TPS) at relevant temperatures and pressures for Martian entry conditions. This paper covers the development and validation of MEDLI2 flight lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material Super-Lightweight Ablator (SLA-561V). Virgin and char thermal conductivities were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties such as virgin and char density, emissivity, absorptivity, and specific heat capacitance was also characterized and compared to the “Heritage” models used during the TPS design phase of Mars 2020. Fully Implicit Ablation and Thermal response (FIAT) simulations were completed using the Heritage and MEDLI2 material response models to provide evidence of the increased accuracy of the MEDLI2 model. FIAT predicted in-depth temperatures were compared to flight lot certification ground-test arc jet test data and MEDLI2 flight thermocouple data.

Material response↗

NASA NTRSDate not supplied

MEDLI2: MISP Measured Aftbody Aerothermal Environments

The Mars Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite on the Mars 2020 mission included two total heat flux sensors and one radiometer on the backshell to directly measure the aftbody aerothermal environments during entry into the Martian atmosphere. All three sensors successfully returned aftbody entry heating measurements. Comparisons between the total heat flux sensor measurements and DPLR/NEQAIR predictions show excellent agreement and provide confidence in the models. The radiometer measured significant radiative heating but compared to the model predictions the signal was attenuated by 50% at the end of the entry heat pulse. The loss of signal is attributed to blockage by thermal protection system (TPS) ablation product deposits on the radiometer window. Ground-based testing in the NASA Ames arc jet facilities was conducted to understand the impact of ablation product deposits on the measured radiometer signal. A discussion of the test results, how flight-like the test conditions were, and future work to further characterize the effect of TPS ablation product deposits on the radiometer performance are presented. In addition to measuring the entry heat pulse all three sensors were sensitive enough to measure solar radiation during cruise, the radiometer measured solar flux during the entry heat pulse, and the leeside total heat flux sensor picked up the descent reaction control system firings.

Ruth A Miller↗

NASA NTRSDate not supplied

Case Study of Meteoroid Fluence on a Mars Sample Return Mission

The Mars Sample Return Campaign must satisfy a Back Planetary Protection requirement that limits the risk of biological contamination of the Earth by Martian microbes. The Earth Re-turn Orbiter (ERO), being developed by the European Space Agency (ESA), will carry a Capture, Containment and Return System (CCRS), which is being developed by NASA to retrieve orbiting samples (OS) from Mars orbit, surround them with two containment layers to create a Contained OS (COS), and transfer the COS to the Earth Entry System (EES), which will be re-leased by ERO to carry the samples through entry, descent and landing at the Utah Test and Training Range. Micrometeoroid impact damage to the Thermal Protection System (TPS) of the EES, which may occur at any time in the ERO mission, is recognized as a potential risk driver for loss of sample containment that needs to be rigorously assessed. A Micrometeoroid Protection System (MMPS) will be implemented to limit that risk. The MMPS consists of a shield covering the TPS called the Micrometeoroid Garage (MMG) and a system of cameras to inspect the TPS. An extensive study was performed by the CCRS Project in collaboration with the NASA Engineering and Safety Center (NESC)to assess the probability of damage to the MMG and TPS by meteoroids over the entire ERO mission. This included the computation of the meteoroid fluence on the MMG and directly on the TPS after EES separation, and assessment of damage to the MMG and TPS via hypervelocity impact tests, hydrocode simulations, and empirical damage prediction and ballistic limit equations (BLEs). The focus of this paper is the meteoroid fluence on the MMG.

Micrometeoroid↗

NASA NTRSDate not supplied

Data Fusion of In-Flight Aerothermodynamic Heating Measurements Using Kalman Filtering

On February 18th, 2021, the Mars 2020 entry system successfully delivered the Perseverance rover to the surface of Mars at Jezero Crater. The entry capsule carried instrumentation installed on the heatshield and backshell, named the Mars Entry, Descent, and Landing Instrumentation 2. The instruments included pressure transducers, thermocouples, heat flux gauges, and a radiometer to measure the aerodynamic and aerothermodynamic performance of the entry vehicle. Three of these sensors, a thermocouple plug, heat flux gauge, and a radiometer, were co-located on the backshell. The sensors were exposed to roughly the same aerodynamic heating, but measured these environments in different ways, each with its own set of modeling and measurement error complications. This paper develops a method for blending each of these measurements together in a single algorithm to produce estimates of the aerothermodynamic environments at that backshell location. The approach makes use of the Kalman-Schmidt filter/smoother methodology, where systematic measurement error parameters are modeled as multiplicative states that are estimated by the filter along with the aerothermal states. The results indicate peak convective and radiative heating values of 0.86 and 5.16 W/cm2, respectively, compared to the filter predictive model values of 0.67 and 4.83 W/cm2.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Data Fusion of In-Flight Aerothermodynamic Heating Measurements Using Kalman Filtering

On February 18th, 2021, the Mars 2020 entry system successfully delivered the Perseverance rover to the surface of Mars at Jezero Crater. The entry capsule carried instrumentation installed on the heatshield and backshell, named the Mars Entry, Descent, and Landing Instrumentation 2. The instruments included pressure transducers, thermocouples, heat flux gauges, and a radiometer to measure the aerodynamic and aerothermodynamic performance of the entry vehicle. Three of these sensors, a thermocouple plug, heat flux gauge, and a radiometer, were co-located on the backshell. The sensors were exposed to roughly the same aerodynamic heating, but measured these environments in different ways, each with its own set of modeling and measurement error complications. This paper develops a method for blending each of these measurements together in a single algorithm to produce estimates of the aerothermodynamic environments at that backshell location. The approach makes use of the Kalman-Schmidt filter/smoother methodology, where systematic measurement error parameters are modeled as multiplicative states that are estimated by the filter along with the aerothermal states. The results indicate peak convective and radiative heating values of 0.86 and 5.16 W/cm$^2$, respectively, compared to the filter predictive model values of 0.67 and 4.83 W/cm$^2$.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Case Study of Meteoroid Fluence on a Mars Sample Return Mission

This paper presents results from an analysis to assess the fluence of meteoroids on the Mars Sample Return Campaign Micrometeoroid Protection System (MMPS) and probability of damage to the Earth Entry System Thermal Protection System (TPS). Results are presented for the mission Outbound trajectory from Earth to Mars. The MEM3 meteoroid environment model was used for the assessment. Results are presented showing the reduction in fluence on cube faces and on the MMPS that can be achieved by selection of an anti-velocity orientation of the MMPS. A methodology is presented that determines the cumulative fluence on the MMPS using the MEM3 meteoroid fluxes and the spacecraft attitude profile over the trajectory. Resulting distributions of fluence over impact velocity, angle, and mass are presented. The fluence results are used to establish velocity-angle scenarios for hydrocode simulation and to assess net damage fluence to the TPS. Example tables containing Smooth Particle Hydrodynamics Code (SPHC) simulation scenarios as well as hypothetical hydrocode simulation scenarios for illustration purposes are presented. The tables present the resulting net damaging fluence to the TPS for each scenario and the total across the scenarios. Additionally, examples of CTH hydrocode simulation are included, demonstrating their use for determining critical impactor across the impactor parameter space, and damage of impactors that penetrate the MMPS.

Micrometeoroid↗

NASA NTRSDate not supplied

Thermal Protection Systems (TPS) for High Velocity Earth Entry Missions

The fastest man-made object to re-enter into Earth’s atmosphere, with an entry velocity of 12.8 km/s, was the Stardust capsule, which returned samples from the comet Wild 2. Sample return missions offer high and long-lasting science yield; as such, they are discussed repeatedly in the latest planetary science decadal survey, titled Origins, Worlds, and Life. An advantage of sample return missions over in situ measurements is the ability to use state-of-the-art instruments that are not limited in power, size, or complexity; conversely, in situ measurements rely on instruments optimized to fit within the limitations of the spacecraft. Additionally, sample return provides the opportunity to revisit samples as analysis techniques improve as well as to further investigate unanticipated or ambiguous results. As launch vehicle and propulsion technologies continue to advance, it is becoming feasible to consider sample return missions from further out in the Solar System beyond Mars orbit. However, returning samples from increasingly distant destinations comes with high entry velocities, and thus requires ever more capable thermal protection systems (TPS). Evaluating the capabilities of existing mature TPS materials for a range of entry conditions and sample return aeroshell configurations is key to establishing the feasibility of future mission proposals. As such, this presentation describes the comprehensive trade study done to evaluate the feasibility of high velocity Earth entry missions with the currently available TPS materials.

Hannah S Alpert↗