Search NASA⌕ Search

Engineering topics

Togay, Mustafa

Publications and source records attributed to Togay, Mustafa.

The effect of remnant CdSe layers on the performance of CdSeTe/CdTe photovoltaic devices

Thin film CdTe-based photovoltaic devices have achieved high efficiency above 22 %. The recent improvement in efficiency is due to Se alloying in the CdTe absorbers to form a CdSeTe/CdTe structure. The subsequent band gap grading increases the short circuit current density. The Se can be introduced by depositing a precursor thin film of either CdSe or a CdSeTe alloy and then diffusing the Se into the CdTe during the high temperature cadmium chloride activation process. Using CdSe is preferred because it is easier to control the Se concentration. However, during fabrication of the CdSeTe/CdTe devices, the CdSe thickness needs to be precisely controlled to prevent the retention of a CdSe remnant layer after the activation treatment. Retention of a remnant CdSe layer causes a dramatic reduction in device efficiency. In this work, we show that the reduction in efficiency is caused by a number of factors. The remnant CdSe layer is n-type which moves the position of the p-n junction. Also, it is widely thought that the CdSe remnants are photo-inactive. In this work, we clarify that the individual CdSe grains are actually highly photo-active. However, the grain sizes in the CdSe remnant and the adjacent CdSeTe layer are very small resulting in a high grain boundary area. Although the grain boundaries are passivated with chlorine, cathodoluminescence imaging and electrical measurements show that this is only partially effective. Also, EQE measurements show that the remnant CdSe causes parasitic absorption. Overall, the remnant CdSe layer causes a reduction in short circuit current density and device efficiency. The thickness of the CdSe precursor layer and the cadmium chloride activation process conditions must be precisely optimised to ensure that all the CdSe is consumed and inter-diffused to form the CdSeTe alloy for highest efficiency devices.

CdSe remnant↗

SnO2 Buffer Layers for High Efficiency CdSeTe/CdTe Devices

SnO2 buffer layers of different thickness were deposited onto TEC 15 Fluorine doped tin oxide coated glass substrates using rf magnetron sputtering. The buffer layers were then incorporated into Cu-doped CdSeTe/CdTe devices using a range of CdCl 2 activation treatments and CuCl2 annealing temperatures to determine the effects of buffer layer thickness on device performance. Results show that all devices fabricated with thinner buffer layers resulted in much better J - V characteristics than their thicker counterparts. This was mainly due to a reduced open-circuit voltage (Voc) when using thicker buffer layers. The best device produced a conversion efficiency of 16.59%, fill factor of 71.62%, Jsc of 28.44 mA/cm 2 and Voc of 814.23 mV.

buffer layers↗

Sodium doping of solution-processed amine-thiol based CIGS solar cells by thermal evaporation of NaCl

Poor crystallinity, high degree of porosity and rough surfaces are the main drawbacks of solution-processed CIGS absorbers resulting in lower power conversion efficiencies when compared to vacuum-based CIGS solar cells. Therefore, promoting absorber grain growth is key to further improve solution-based solar cell performance. The effect of alkali elements such as Na in CIGS absorbers is generally recognised to have beneficial effects not only on the absorber opto-electronic properties but also on the grain growth. In this work, thermal evaporation of a thin layer of NaCl prior to selenisation resulted in absorbers with significantly larger CIGS grains than previously seen with Na diffusing directly from the from soda-lime glass substrate. NaCl is non-toxic, abundant and readily available compound that has not been typically used as an evaporation source, but rather as an additive into CIGS precursor solution. The effect of Na on these solution-processed CIGS devices was primarily observed in the spectacular morphological changes leading to improved carrier collection and minority carrier lifetimes, but less on the absorber doping. Transmission electron microscopy (TEM) revealed voids forming around large CIGS grains upon NaCl addition and these had a negative effect on inter-grain carrier transport. Nonetheless, the resulting device performance doubled from 5% to 10% with addition of Na using this doping approach; however, a compromise between the optimum grain growth and optimum electronic properties had to be made. This study demonstrates a novel, simple and effective Na-doping strategy for CIGS absorbers and reveals the current limitations of the Na-doping in solution-processed atmospherically deposited cells.

14 SOLAR ENERGY↗

Light-Induced Metastabilities in Highly Efficient MZO/CdSeTe/CdTe Thin Film Solar Cells

Metastability effects have been investigated in high efficiency MZO/CdSeTe/CdTe solar cells. Two different preconditioning procedures have been studied to recover the performance of the devices. These preconditioning procedures include light soaking, annealing and cooling down the device under different atmospheric conditions. J-V curves before any preconditioning showed a `S` shaped behavior and disappears after 15 minutes of light soaking under 1000 Wm-2. Both Atmospheric and Vacuum preconditioning showed similar recovery of the device performance. However, this recovery only lasts for 3 days when the devices were kept under vacuum in the dark.

14 SOLAR ENERGY↗