Search NASA⌕ Search

Engineering topics

Tong, Yang

Publications and source records attributed to Tong, Yang.

At least 19 records

Extraordinary creep resistance in a non-equiatomic high-entropy alloy from the optimum solid-solution strengthening and stress-assisted precipitation process

Improving creep resistance has commonly been achieved by the optimization of alloy design that results into strong solid-solution strengthening and/or coherent precipitates for dislocation blockage. High-entropy alloys (HEAs), despite their single-phase solid-solution nature, only exhibit creep properties that are comparable to precipitate-strengthened ferritic alloys. Moreover, many HEAs are found to be plagued with many incoherent second phases after long-term annealing, which reduces the lifetime and thus prohibits their usage at elevated temperatures. The present work demonstrates the extraordinary creep resistance of a non-equiatomic Al 0.3 CoCrFeNi HEA, in which the creep strain rate is found to be several orders of magnitude lower than the Cantor alloy and its subsets. Using a suite of characterization tools such as atom probe tomography (APT) and transmission electron microscopy (TEM), it was shown that a B2 precipitate phase that has been widely seen during annealing is suppressed during the early stage of the creep deformation. Currently, metastable and coherent L1 2 precipitates emerge and provide significant creep strengthening. This observation is rationalized by the coupling between the applied stress and the lattice mismatch. In the range of 973 ~ 1033 K, the stress exponent and activation energy were determined to be 3–6.53 and 390–548.2 kJ·mol –1 , respectively. The creep lifetime, on the other hand, is comparable to Cantor subset alloys because the precipitate free zone near the grain boundaries does not provide sufficient constraint for the grain boundary cavity growth. Furthermore, the present work provides a pathway to design novel HEAs with improved creep resistance.

36 MATERIALS SCIENCE↗

Viscoelasticity-induced structure anisotropy in amorphous materials

Viscoelasticity-induced structural change in Zr 55 Cu 30 Ni 5 Al 10 metallic glass (Zr-MG) and amorphous selenium (a-Se) is investigated using synchrotron X-ray diffraction. By analyzing the two-dimensional diffraction pattern, two types of structural anisotropy with the feature of the residual elastic strain or heterogeneous intensity of diffraction rings are revealed. The origin of the structural anisotropy is attributed to the topological rearrangement in the Zr-MG and conformation rearrangement in the a-Se. In conclusion, our findings bring a structural identity to the phenomenological structureless deformation defect widely used in different amorphous materials.

36 MATERIALS SCIENCE↗

Nonaffine Strains Control Ductility of Metallic Glasses

The origin of limited plasticity in metallic glasses is elusive, with no apparent link to their atomic structure. In this study, we propose that the response of the glassy structure to applied stress, not the original structure itself, provides a gauge to predict the degree of plasticity. We carried out high-energy x-ray diffraction on various bulk metallic glasses (BMGs) under uniaxial compression within the elastic limit and evaluated the anisotropic pair distribution function. We show that the extent of local deviation from the affine (uniform) deformation in the elastic regime is strongly correlated with the plastic behavior of BMGs beyond yield, across chemical compositions and sample history. The results suggest that the propensity for collective local atomic rearrangements under stress promotes plasticity.

3-dimensional systems↗

Stress-controlled fatigue of HfNbTaTiZr high-entropy alloy and associated deformation and fracture mechanisms

The stress-controlled fatigue tests are carried out at a stress ratio of 0.1 and a frequency of 10 Hz, and span both low-cycle and high-cycle regimes by varying the applied stress amplitudes. The high-cycle fatigue regime gives a fatigue strength of 497 MPa and a fatigue ratio of 0.44. At equivalent conditions, the alloy's fatigue strength is greater than all other high-entropy alloys (HEAs) with reported high-cycle fatigue data, dilute body-centered cubic alloys, and many structural alloys such as steels, titanium alloys, and aluminum alloys. Through in-depth analyses of crack-propagation trajectories, fracture-surface morphologies and deformation plasticity by means of various microstructural analysis techniques and theoretical frameworks, the alloy's remarkable fatigue resistance is attributed to delayed crack initiation in the high-cycle regime, which is achieved by retarding the formation of localized persistent slip bands, and its good resistance to crack propagation in the low-cycle regime, which is accomplished by intrinsic toughening backed up by extrinsic toughening. Additionally, the stochastic nature of the fatigue data is neatly captured with a 2-parameter Weibull model.

36 MATERIALS SCIENCE↗

First-principles calculation of lattice distortions in four single phase high entropy alloys with experimental validation

Exceptional properties of high entropy alloys (HEAs) are attributed to the disordered random solid solution of multiple alloying elements. Despite numerous studies, the fundamental understanding at the electronic and atomic levels is still missing. We report a comparative study of four fcc HEAs of NiFeCoCr and NiFeCoCrX (X = Mn, Cu, or Pd) based on ab initio calculations using large supercells with 500 atoms in equal composition. After fully optimizing their structures using the VASP package, their electronic structure, interatomic bonding, partial charge distribution, and mechanical properties are calculated and compared, revealing the intricate interdependence among them. A novel parameter based on the quantum mechanical metric for internal cohesion, the total bond order density (TBOD), is used to interpret the calculated properties. The highest TBOD is found in Cantor alloy NiFeCoCrMn but lower in NiFeCoCrPd. The atomic radii vary depending on their local chemical environment. The resulting lattice distortions is validated experimentally in NiFeCoCrMn and NiFeCoCrPd. Moreover, modeling of Cu and Pd clustering in the supercell shows they have lower total energy in agreement with the observation of Cu-enhanced nano-participates in NiFeCoCrCu and Pd-induced concentration wave in NiFeCoCrPd HEAs.

36 MATERIALS SCIENCE↗

Charge transfer effect on local lattice distortion in a HfNbTiZr high entropy alloy

We report it is often assumed that atoms are hard spheres in the estimation of local lattice distortion (LLD) in high-entropy alloys (HEAs). However, our study demonstrates that the hard sphere model misses the key effect, charge transfer among atoms with different electronegativities, in the understanding of the severely distorted local structure in the body-centered cubic (BCC) HfNbTiZr HEA. Through the characterization and simulations of the local structure of the HfNbTiZr HEA, we found that the LLD regions in HfNbTiZr have larger average size compared with face-centered cubic (FCC) HEAs, but the magnitude of LLD significantly varies from one atomic site to another because of electron transfer from larger atoms, Hf and Zr, to smaller ones, Nb and Ti. Our finding may form the basis for the design of high performance HEAs through tuning their site-to-site chemical heterogeneity.

36 MATERIALS SCIENCE↗

Dislocation loop evolution and radiation hardening in nickel-based concentrated solid solution alloys

Effects of chemical composition, ion irradiation dose and temperature on unfaulting of irradiation induced Frank dislocation loops to perfect loops in two nickel based single-phase solid solution alloys, Ni–20Fe and NiFe–20Cr, have been studied. The fraction of Frank loops decreases with irradiation dose from 7.2 to 38.4 dpa at 500°C, but with more Frank loops remaining in the ternary alloy. However, perfect loops and dislocation networks become the dominant features of defects at 580°C in both alloys. The results indicate a thermally assisted loop unfaulting process that may be hindered by more sluggish defect motion in the alloy with more chemical components. Nano-indentation with both continuous stiffness method and single indentation method are used to measure radiation hardening. Loop unfaulting in both alloys irradiated at 580°C reduced radiation hardening while significant hardening is observed after irradiation at 500°C. The quasi-static single indentation method exhibits lower hardness results compared to continuous stiffness method, because dislocations induced from the cyclic loading in the latter method get relaxed and stabilized, resulting in higher resistance to the indenter.

36 MATERIALS SCIENCE↗

Local structure of Ni 80 X 20 (X: Cr, Mn, Pd) solid-solution alloys and its response to ion irradiation

In this work, the local structure of Ni 80 X 20 (X: Cr, Mn, Pd) solid-solution alloys was investigated with x-ray absorption and total scattering x-ray diffraction methods. Atomic pair distribution function (PDF) analysis indicated that the local lattice distortion is strongly relevant to the atomic size mismatch, and the local lattice distortion in Ni80Pd20 alloy is obviously larger than that in other solid-solution alloys. The bond length of different atomic pairs was derived from the fitting of extended x-ray absorption fine structure spectra. Quantitative analysis of the local bonding environment in Ni 80 Cr 20 during Ni ion irradiation suggested that Cr atoms tend to form clusters in Ni 80 Cr 20 with the increase of ion dose.

36 MATERIALS SCIENCE↗

Effects of 3d electron configurations on helium bubble formation and void swelling in concentrated solid-solution alloys

Currently, elemental specific chemical complexity is known to play a vital role in microstructure development in single-phase concentrated solid-solution alloys (SP-CSAs), including both He bubble formation and irradiation-induced void swelling. While cavity formation and evolution under ion irradiation at elevated temperature are complex nonequilibrium processes, chemical effects are revealed at the level of electrons and atoms herein in a simplified picture, using Ni and a special set of Ni-based SP-CSAs composed of 3d transition metals as model alloys. Based on Ni and the model alloys with minimized variables (e.g., atomic mass, size, and lattice structure), we report on the effects of chemically-biased energy dissipation, defect energetics, sluggish diffusion, and atomic transport on cavity formation and evolution under both self-ion Ni irradiation and He implantation. The observed difference in microstructure evolution is attributed to the effects of d electron interactions in their integrated ability to dissipate radiation energy. The exhibited impact of alloying 3d transition metals with larger differences in the outermost electron counts suggests a simple design strategy for tuning defect properties to improve radiation tolerance in structural alloys.

36 MATERIALS SCIENCE↗

Critical Review of Chemical Complexity Effect on Local Structure of Multi-principal-Element Alloys

The multi-principal-element alloy (MPEA) strategy has radically changed the pathway of alloy development by shifting the search for useful alloys from the corners to the center region of the phase diagram. Distinct from conventional one-principal-element alloys, chemically complex MPEAs exhibit extreme diversity in terms of atomic size and chemistry, potentially distorting their local structure. In this study, we summarize recent experimental and theoretical progress on study of the local structure of such materials, with emphases on local lattice distortion and the charge transfer effect.

36 MATERIALS SCIENCE↗

Strain engineering 4H-SiC with ion beams

Single crystals of 4H-SiC irradiated with 900 keV Si and 21 MeV Ni ions separately and sequentially were examined by Rutherford backscattering spectrometry in channeling geometry, single crystal X-ray diffraction, and Raman scattering. SiC irradiated with 900 keV Si ions to a fluence of 6.3 × 10 14 ions/cm 2 experiences 7.3% strain over the depth of 650 nm. Strain relaxation from ionization-induced annealing was directly studied due to subsequent irradiation with 21 MeV Ni ions to a fluence of 2 × 10 14 ions/cm 2 . These competitive processes suggest the use of ion irradiation to create a specific strain state in 4H-SiC, particularly in films.

36 MATERIALS SCIENCE↗

Grain growth and Hall-Petch relationship in a refractory HfNbTaZrTi high-entropy alloy

Understanding the effect of temperature variation on the microstructural evolution is particularly important to refractory high-entropy alloys (RHEAs), given their potential high-temperature applications. Here, we experimentally investigated the grain-growth behavior of the HfNbTaZrTi RHEAs during recrystallization at temperatures from 1,000 to 1,200 °C for varied durations, following cold rolling with a 70% thickness reduction. Following the classical grain-growth kinetics analysis, two activation energies are obtained: 205 kJ/mol between 1,000 and 1,100°C, and 401kJ/mol between 1,100 and 1,200°C, which suggests two mechanisms of grain growth. Moreover, the yield strength – grain size relation was found to be well described by the Hall-Petch relation in the form of σ y = 942 + 270D -0.5 . It was revealed that the friction stress, 942 MPa, in the HfNbTaZrTi HEA is higher than that of tungsten alloys, which indicates the high intrinsic stress in the BCC-RHEA. Further, the coefficient, 270 MPa/μm -1/2 , is much lower than that in the 316 stainless steel and Al 0.3 CoCrFeNi HEAs, which indicates low grain-boundary strengthening.

36 MATERIALS SCIENCE↗

Additive Manufacturing of High-Entropy Alloys: A Review

Owing to the reduced defects, low cost, and high efficiency, the additive manufacturing (AM) technique has attracted increasingly attention and has been applied in high-entropy alloys (HEAs) in recent years. It was found that AM-processed HEAs possess an optimized microstructure and improved mechanical properties. However, no report has been proposed to review the application of the AM method in preparing bulk HEAs. Hence, it is necessary to introduce AM-processed HEAs in terms of applications, microstructures, mechanical properties, and challenges to provide readers with fundamental understanding. Specifically, we reviewed (1) the application of AM methods in the fabrication of HEAs and (2) the post-heat treatment effect on the microstructural evolution and mechanical properties. Compared with the casting counterparts, AM-HEAs were found to have a superior yield strength and ductility as a consequence of the fine microstructure formed during the rapid solidification in the fabrication process. The post-treatment, such as high isostatic pressing (HIP), can further enhance their properties by removing the existing fabrication defects and residual stress in the AM-HEAs. Furthermore, the mechanical properties can be tuned by either reducing the pre-heating temperature to hinder the phase partitioning or modifying the composition of the HEA to stabilize the solid-solution phase or ductile intermetallic phase in AM materials. Moreover, the processing parameters, fabrication orientation, and scanning method can be optimized to further improve the mechanical performance of the as-built-HEAs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Lattice Distortion and Phase Stability of Pd-Doped NiCoFeCr Solid-Solution Alloys

In the present study, we have revealed that (NiCoFeCr)100−xPdx (x= 1, 3, 5, 20 atom%) high-entropy alloys (HEAs) have both local- and long-range lattice distortions by utilizing X-ray total scattering, X-ray diffraction, and extended X-ray absorption fine structure methods. The local lattice distortion determined by the lattice constant difference between the local and average structures was found to be proportional to the Pd content. A small amount of Pd-doping (1 atom%) yields long-range lattice distortion, which is demonstrated by a larger (200) lattice plane spacing than the expected value from an average structure, however, the degree of long-range lattice distortion is not sensitive to the Pd concentration. The structural stability of these distorted HEAs under high-pressure was also examined. The experimental results indicate that doping with a small amount of Pd significantly enhances the stability of the fcc phase by increasing the fcc-to-hcp transformation pressure from ~13.0 GPa in NiCoFeCr to 20–26 GPa in the Pd-doped HEAs and NiCoFeCrPd maintains its fcc lattice up to 74 GPa, the maximum pressure that the current experiments have reached.

36 MATERIALS SCIENCE↗