Search NASA⌕ Search

Engineering topics

Torregrosa, Frank

Publications and source records attributed to Torregrosa, Frank.

Plasma immersion ion implantation for sub-22 nm node devices: FD-SOI and Tri-Gate

Here, we present and discuss the electrical characteristics of fully depleted MOSFET transistors of planar and tridimensional architecture, doped by Plasma Immersion Ion Implantation (PIII) or Beam Line Ion Implantation (BLII). Both techniques delivered similar and satisfactory results in considering the planar architecture. For tri-dimensional Tri-Gate transistors, the results obtained with PIII are superior.

36 MATERIALS SCIENCE↗

Simulation of BF{sub 3} plasma immersion ion implantation into silicon

Plasma immersion ion implantation from a BF{sub 3} plasma into crystalline (100) silicon was performed using the PULSION plasma doping tool. Implanted boron profiles were measured with the SIMS method and simulated using models with different levels of sophistication. The physical implantation model is based on an analytical energy distribution for ions from the plasma and uses a Monte-Carlo simulation code. An analytical model of plasma immersion ion implantation that assumes a uniform and isotropic implantation was implemented in a software module called IMP3D. The functionality of this module which was initially envisaged for the three-dimensional simulation of conventional ion implantation was extended to plasma immersion ion implantation and examples of 2D and 3D simulations from this are presented.

36 MATERIALS SCIENCE↗

BF{sub 3} PIII modeling: Implantation, amorphisation and diffusion

In the race for highly doped ultra-shallow junctions (USJs) in complementary metal oxide semi-conductor (CMOS) technologies, plasma immersion ion implantation (PIII) is a promising alternative to traditional beamline implantation. Currently, no commercial technology computer aided design (TCAD) process simulator allows modeling the complete USJ fabrication process by PIII, including as-implanted dopant profiles, damage formation, dopant diffusion and activation. In this work, a full simulation of a p-type BF{sub 3} PIII USJ has been carried out. In order to investigate the various physical phenomena mentioned above, process conditions included a high energy/high dose case (10 kV, 5 Multiplication-Sign 10{sup 15} cm{sup -2}), specifically designed to increase damage formation, as well as more technology relevant implant conditions (0.5 kV) for comparison. All implanted samples were annealed at different temperatures and times. As implanted profiles for both boron and fluorine in BF{sub 3} implants were modeled and compared to Secondary Ion Mass Spectrometry (SIMS) measurements. Amorphous/crystalline (a/c) interface depths were measured by transmission electron microscopy (TEM) and successfully simulated. Diffused profiles simulations agreed with SIMS data at low thermal budgets. A boron peak behind the a/c interface was observed in all annealed SIMS profiles for the 10 kV case, indicating boron trapping from EOR defects in this region even after high thermal budgets. TEM measurements on the annealed samples showed an end of range (EOR) defects survival behind the a/c interface, including large dislocation loops (DLs) lying on (001) plane parallel to the surface. In the last part of this work, activation simulations were compared to Hall measurements and confirmed the need to develop a (001) large BICs model.

36 MATERIALS SCIENCE↗

Ultra-Shallow Junctions Fabrication by Plasma Immersion Implantation on PULSION registered Followed by Laser Thermal Processing

In order to achieve the requirements for P+/N junctions for <45 nm ITRS nodes, ultra low energy and high dose implantations are needed. Classical beamline implantation is now limited in low energies, compared to Plasma Immersion Ion Implantation (PIII) which efficiency is no more to prove for the realization of Ultra-Shallow Junctions (USJ) in semiconductor applications : this technique allows to get ultimate shallow profiles (as implanted) due to no lower limitation of energy and high dose rate. Electrical activation is also a big issue since it has to afford high electrical activation rate with very low diffusion. Laser annealing is one of the candidates for the 45 nm node. This paper presents electrical and physico-chemical characterizations of junctions realized with BF3 PIII followed by laser thermal processing with aim to obtain ultra-shallow junctions. Different implantation conditions (acceleration voltage/dose) and laser conditions (laser types, fluence/number of shots) are used for this study. Pre-amorphization is also used to confine the junction depth, and is shown to have a positive effect on junction depth but leads in higher junction leakage due to the remaining of EOR defects. The characterization is done using Optical characterization tool (SEMILAB) for sheet resistance and junction leakage measurements. SIMS is used for Boron profile and junction depth.

36 MATERIALS SCIENCE↗

Fabrication of Ultra-Shallow Junctions on 300 mm Wafers Using the Plasma Immersion Implanter PULSION registered Followed by Spike Annealing Using LEVITOR Furnace

Thanks to the European Project SEA-NET, an industrial version of the IBS Plasma Ion Implantation tool has been installed in LETI for the fabrication of Ultra-Shallow Junction for 45 and 32 nm CMOS on 200 and 300 mm wafers. In this study, we present first doping results on 300 mm wafers using BF{sub 3} plasma. Annealing after PULSION implantation is performed by the ASM furnace LEVITOR. This tool, which works on conduction heating is emissivity independent for temperature control and allows reaching high ramp up and ramp down speeds (up to 900 deg. C/s). Main characteristics of as implanted wafers are presented (metal contamination 2E10/cm{sup 2}, SIMS depth profiles down to 5 nm). Then the effect of convection gas in the annealing process on sheet resistance, junction depth and uniformity is presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

PULSION registered: A Versatile 200 to 300 mm Bridge Tool Plasma Immersion Ion Implanter for Ultra-Shallow Doping and Nanotechology Applications

Thanks to the European Projects SEA-NET and PULLNANO, an industrial version of the IBS Plasma Ion Implantation tool has been installed in LETI for the fabrication of Ultra-Shallow Junctions for 45 and 32 nm CMOS on 200 and 300 mm wafers. In this paper, we present the main machine characteristics (layout, contamination, homogeneity, reproducibility, uptime) and we show that implanted wafers are compatible with the 32 nm nodes requirements. Then doping results (sheet resistance vs junction depth and leakage current) using several annealing technics are presented (laser, flash and spike anneals). In the second part of the paper, versatility of the tool is demonstrated with its use for other applications (3D doping, hydrogenation, solar cells...)

36 MATERIALS SCIENCE↗