Search NASA⌕ Search

Engineering topics

Trabia, Mohamed

Publications and source records attributed to Trabia, Mohamed.

Gas Gun-Configured Magnetic Flux Compression Generator, NLV-013-17, Year 1 of 3

Presentation on project to explore the concept of achieving current amplification by principles of high-explosive magnetic compression generation but without high explosives and demonstrate that a gas gun or launcher could be configured to provide the input energy and action necessary for magnetic compression generation performance in a more controlled, cost-effective manner with improved safety.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling of Hypervelocity Impact Experiments Using Gamma-SPH Technique

Hypervelocity impact research has been conducted using light gas guns to characterize materials under shock conditions. Hypervelocity impact produces high pressure and temperature states during the projectile-target interaction. Projectile and target materials both experience severe localized deformation under these conditions, which creates stretching, bending, and complete perforation in thin target plates. Relatively thick target plates show several failure modes, such as spalling, petalling, discing, and plugging. These failure modes are mostly controlled by several factors such as impact velocity, material properties, loading geometry, etc. Gas gun experiments were performed to measure the plastic deformation of steel plates during hypervelocity impact. The MPDV system was used to measure free surface velocity during these experiments. Simulation models developed in the IMPETUS AFEA Gamma SPH solver show that the physical measurements of impact cratering and bulge are in reasonable agreement with simulation results. Velocity profiles are in general agreement with the experiments capturing all the major features observed experimentally.

36 MATERIALS SCIENCE↗

Failure Mechanisms in Fored, Layered, and Additive Manufactured Titanium due to Hypervelocity Impact: Experiments and Simulations

This article presents a study of dynamic failure events in forged, layered, and additive manufactured (AM) titanium alloy subject to hypervelocity impact. Experiments were conducted using a two stage light-gas gun, 0.22-caliber Lexan projectiles, and different types of titanium target plates. A four-channel Photonic Doppler Velocimetry (PDV) system was used to study the free surface velocities to provide an understanding of the different failure mechanisms in these materials. The experimental measurements were used to validate computational simulations, which describe the behavior of these materials under shock. It was determined that AM, forged titanium, and multi-layered stacks produce similar velocity profiles during the early stage of impact, with the AM targets exhibiting spall at lower velocities and the multi-layered stacks exhibiting vibrations between plates. Simulations of solid and layered forged materials provide a good match to experimental data.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Study of hypervelocity projectile impact on thick metal plates

Hypervelocity impacts generate extreme pressure and shock waves in impacted targets that undergo severe localized deformation within a few microseconds. These impact experiments pose unique challenges in terms of obtaining accurate measurements. Similarly, simulating these experiments is not straightforward. This paper proposed an approach to experimentally measure the velocity of the back surface of an A36 steel plate impacted by a projectile. All experiments used a combination of a two-stage light-gas gun and the photonic Doppler velocimetry (PDV) technique. The experimental data were used to benchmark and verify computational studies. Two different finite-element methods were used to simulate the experiments: Lagrangian-based smooth particle hydrodynamics (SPH) and Eulerian-based hydrocode. Both codes used the Johnson-Cook material model and the Mie-Grüneisen equation of state. Experiments and simulations were compared based on the physical damage area and the back surface velocity. Finally, the results of this study showed that the proposed simulation approaches could be used to reduce the need for expensive experiments.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Comparison of Failure Mechanisms Due to Shock Propagation in Forged, Layered, and Additive Manufactured Titanium

This chapter for the Stewardship Science Academic Programs Annual Report describes a project focused on characterizing the shock propagation and failure mechanisms in forged, layered, and additive manufactured (AM) materials. The AM process fabricates a part layer by layer, which provides opportunities to tailor geometry and optimize structural performance in addition to minimizing the amount of material waste for odd shaped parts.

36 MATERIALS SCIENCE↗

Characterization of Shock Propagation and Failure Mechanisms in Composite and Additive Manufactured Materials NLV-16-15, Year 1 of 3

Presentation describes effort to introduce experimental and simulation techniques for understanding the behavior of additive manufactured titanium under shock loading by conducting a series of ballistic impact experiments with two-stage light gas gun on titanium targets and using Photonic Doppler Velocimetry (PDV) techniques to measure free surface velocity.

74 ATOMIC AND MOLECULAR PHYSICS↗

Use of a Multiplexed Photonic Doppler Velocimetry (MPDV) System to Study Plastic Deformation of Metallic Steel Plates in High Velocity Impact

High-velocity impact experiments with a gas gun pose unique challenges, in terms of experimental setup and computational simulation, since the projectile-target interaction creates extreme pressure and temperature within few micro seconds. The objective of this study is to accurately measure the plastic deformation of plates under projectile impact that does not lead to full penetration. In this work, free surface velocities at the back side of target plates are measured using the newly developed Multiplexed Photonic Doppler Velocimetry (MPDV) system, which is an interferometric fiber-optic technique which can measure velocity from the Doppler shift of the light reflected from the moving back surface of the target. The MPDV system allows measurements of velocity from different locations on the target plate using multiple optical fiber probes oriented in specific directions and patterns. Data are reduced using a Fast Fourier transformation (FFT) technique to obtain the free surface velocity profiles. These velocity profiles can present insights into the dynamic behavior of impacted materials under shock loading conditions.

MPDV, multiplexing, high-velocity impact, velocime↗

Modeling Plastic Deformation of Steel Plates in Hypervelocity Impact Experiments

Hypervelocity impact experiments were done with a two-stage light gas gun to study the plastic deformation of metallic plates. Cylindrical Lexan projectiles were fired at A36 steel target plates with a velocity range of 4.5-6.0 km/s. Experiments were designed to produce a front side impact crater and a permanent bulging deformation on the back surface of the target while preventing complete perforation. Free surface velocities from the back surface of target plate were acquired using the newly developed Multiplexed Photonic Doppler Velocimetry (MPDV) system. Two different computational techniques were developed to simulate this type of experiment: Lagrangian-based smooth particle hydrodynamics (SPH) in LS-DYNA and the Eulerian-based hydrocode CTH. Parameters for material models including equation of state, compressive strength, and spall model were selected to obtain highest fidelity numerical results to compare with experiment.

36 MATERIALS SCIENCE↗

Variables Affecting Smooth Particle Hydrodynamics Simulation of High-Velocity Flyer Plate Impact Experiments

This paper describes our work to characterize the variables affecting the smoothed particle hydrodynamics (SPH) method in the LS-DYNA package for simulating high-velocity flyer plate impact experiments. LS-DYNA simulations are compared with one-dimensional experimental data of an oxygen-free high-conductivity (OFHC) copper flyer plate impacting another plate of the same material. The comparison is made by measuring the velocity of a point on the back surface of the impact plate using the velocity interferometer system for any reflector (VISAR) technique.

smoothed particle hydrodynamics, SPH, flyer plate ↗

UNLV Nuclear Hydrogen Initiative

Evaluation of the Crack growth rate (CGR) of Alloy 617 and Alloy 276 under constant K at ambient temperature has been completed. Creep deformation of Alloy 230 at different temperature range and load level has been completed and heat to heat variation has been noticed. Creep deformation study of Alloy 276 has been completed under an applied initial stress level of 10% of yield stress at 950ºC. The grain size evaluation of the tested creep specimens of Alloy 276 has been completed.

36 MATERIALS SCIENCE↗