Search NASA⌕ Search

Engineering topics

Tracy L. Gibson

Publications and source records attributed to Tracy L. Gibson.

5 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Cryogenic Thermal Coatings Final Report

The goals of this project were to produce yttrium oxide- (Y2O3) based tiles and a spray-on coating with minimal solar absorption, to perform exposure testing on these coatings (both rigid and sprayon), and to work towards a manufacturing process whereby these coatings could be made available to the space community. The Key Performance Parameters (threshold values) were to achieve 1% solar absorption for the tiles as measured in a deep space simulator, and 6% solar absorption for the spray-on coating as measured using a reflectance spectrometer. The values achieved were 1.2% (GRC Deep space simulator) and 4% (KSC spectrometer using Spectralon as a reference) for the tiles and spray-on coating, respectively. Exposure testing consisted of measuring tile and spray-on coating degradation due to atomic oxygen, ultraviolet radiation, and electrostatic fields. Atomic oxygen caused some degradation, while ultraviolet exposure caused a significant increase in absorption. However, in-space samples exposed to solar ultraviolet did not show this significant increase. This discrepancy is addressed in this report. As a result of this work, Y2O3 tiles have been manufactured in the Kennedy Space Center (KSC) Applied Chemistry Laboratory (ACL), and the process has been transferred to the Thermal Protection System Facility (TPSF) at KSC. The TPSF manufactures coatings for the space community and is an ideal route by which future users could access Y2O3-based coatings. The spray-on coating has been developed such that it can be applied to a wide range of substrates, substantially lowering absorbed solar power as compared to currently available coatings.

Thermal Control Coatings↗
NASA NTRS2022

XSP Methane Sensors Test and Evaluation Project “M-Step”

Methane sensor technology is employed in industry sectors from oil and gas to agriculture, landfills, and monitoring of natural emissions. The US oil and gas sector is extensive in scale, critical to fulfilling US energy needs, and deals with commodities presenting enormous challenges for personnel safety and the environment. Thus, it is imperative that they have accurate and responsive sensors to detect hazardous gases such as methane. US space launch systems will increasingly also use liquefied methane and liquefied natural gas (LNG), which is mostly methane, in quantities large and small, as main and auxiliary propulsion and power. Some of these systems will be reusable, which adds the unique challenge of processing a vehicle that has residual commodities and has returned to its launch site to be readied for its next launch. The methane sensors test and evaluation project (M-STEP) began within the context of a reusable launch system, the Defense Advanced Research Projects Agency (DARPA) Experimental Spaceplane (XSP) program, which would have employed a high-pressure gaseous methane and gaseous oxygen reaction control system. Although the XSP partnership between Boeing and DARPA was terminated by Boeing in early 2020, DARPA and KSC have continued to collaborate in the area of gas sensors with the hydrogen sensor test and evaluation project (H-STEP) and with M-STEP. The NASA Launch Services program (LSP) invested in M-STEP in FY 2021 “to evaluate and understand the state-of-the-art in methane gas sensors”. M-STEP and the LSP effort was complementary, pushing in the same direction to understand US launch system stakeholder needs and approaches, requirements internal (NASA) and external, and commercially available or forthcoming methane sensing technologies, practices, and approaches. In addition, M-STEP (as with H-STEP) enhances KSC capabilities and understanding of these technologies, informing agency investments and further research in these areas.

Tracy L. Gibson↗
NASA NTRS2021

Modular Composite Damage Detection System (MCDDS)

The 2020 CIF funded Modular Composite Damage Detection System (MCDDS) aims to advance the technology of damage detection in composites in the areas of thin, flexible damage detection panel construction, encapsulation techniques in composite matrixes, innovative integration and interfacing techniques with flexible embedded sensory panels, repair methods of composite materials, and improved packaging of the MCDDS. Custom thin, flexible polyimide printed circuit boards (PCBs) were designed and procured for fabrication of test specimens. A custom interface PCB was designed and fabricated to monitor the newly developed damage detection test specimens. Test specimens were fabricated using the novel flexible circuitry that were either fully or partially encapsulated. The fully encapsulated specimens were used to demonstrate embedded damage detection concepts and the partially encapsulated specimens were used to demonstrate surface-mounted (laminate) damage detection concepts. The new composite damage detection test specimens were tested and evaluated to determine if the novel damage detection sensory panels could withstand low-cycle threshold fatigue loading per a modified version of American Society for Testing and Materials (ASTM) D 7264 for up to 50 cycles without void formation. The data for multiple sensory panels indicates that the newly fabricated sensory panels are robust and do indeed withstand three-point bend flexural loading for more than 50 cycles. Additionally, testing was performed to determine if damage could be detected in damage detection test specimens subjected to failure using a 3-point bend test per a modified version of ASTM D 7264. Again, multiple sensory panels (both fully and partially encapsulated) showed the ability to detect damage to specimens subjected to failure per a modified version of ASTM D 7264. Additionally, a novel concept for tracking and monitoring of cracking (and potentially delamination) in composites was designed and developed that utilizes painted-on conductors.

Christopher Forney↗
NASA NTRSDate not supplied

Selection, Production, and Properties of Regolith Polymer Composites for Lunar Construction

NASA’s Artemis Program seeks to establish a long-term presence on the Moon to enable scientific exploration and expand the cis-lunar economy by utilizing lunar resources through public-private and international partnerships. Over the next decades, a lunar spaceport will need to be established to provide the services and facilities that are necessary to achieve this goal. Robotic construction technologies using in-situ materials must be developed to build up enabling infrastructure such as launch/landing pads, blast protection, power/communications infrastructure, improved roads, improved operational surfaces, and radiation protection shelters. Kennedy Space Center’s Granular Mechanics and Regolith Operations laboratory at Swamp Works has partnered with SpaceFactory and LERA Consulting Structural Engineers to develop the architectural and structural design of an unpressurized lunar shelter. The shelter, called Lunar Infrastructure Asset (LINA), is designed to support 2.3 m of regolith overburden to protect astronauts and surface assets from radiation, meteoroid impact, thermal gradients/cycling, and to withstand moonquakes. LINA’s structural design criteria and the resulting structure design are detailed in separate papers. A Fused Filament Fabrication (FFF) construction process using regolith polymer composites has been developed and is detailed in a separate publication. This paper presents material formulations and selection rationale for each of the composite components that were examined. Formulations include 70:30, 80:20, and 85:15 wt.% mixture ratios of lunar mare simulant Black Point-1 (BP-1): Polylactic Acid (PLA), 80:20 Lunar Highlands Simulant-1 (LHS-1): PLA and an 80:20 BP-1: PLA formulation with a flow enhancer additive. Test samples were printed in simulated lunar dirty thermal vacuum conditions (-190 °C, 10-3 torr). A series of tests were performed on each formulation to characterize the achieved mixture ratio, mechanical strength properties, off-gassing products during vacuum printing, and porosity and density of printed products. The LHS-1: PLA formulation yielded an advantageous combination of properties and was used in a final test that additively constructed a sub-scaled LINA on regolith simulant in dirty vacuum conditions. The materials and construction process presented in this paper are considered to be at Technology Readiness Level (TRL) 5 with additional testing necessary to characterize long term lunar environmental exposure effects.

lunar infrastructure↗