Search NASA⌕ Search

Engineering topics

Travis L Turner

Publications and source records attributed to Travis L Turner.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Aeroelastic Stability Assessment Methodology and Application to Slat Noise Treatments on the High-Lift Common Research Model

This work supports a larger effort at NASA to reduce airframe noise and, thus, environmental noise around airports. The leading-edge slat of conventional high-lift systems is a prominent source of airframe noise, and two technologies were previously identified as promising for noise reduction without significant aerodynamic or weight penalty: the slat cove filler (SCF) and the slat gap filler (SGF). NASA fabricated a 10%-scale semispan aircraft model for wind tunnel testing based upon the High-Lift Common Research Model (CRM-HL). NASA embarked on a test campaign with the 10% CRM-HL to determine the noise reduction effectiveness and other performance metrics of 3D SCF and SGF treatments in flow conditions representative of flight. The highly flexible SCF and SGF treatments posed a risk to the model and aeroelastic instability would compromise research integrity, so aeroelastic stability assessment was required. This work briefly describes the 10% CRM-HL, design of the SCF and SGF treatments to the model, and supporting fluid structure interaction (FSI) research. Relations for static and dynamic aeroelastic similitude are then developed for convenience of reference, and simplifications are introduced of particular utility to the cases considered in this study. The similitude relations are employed to assess the stability of the treatments under wind tunnel flow conditions based upon known behaviors from the supporting research. It is shown that the treatments are safe for test under the anticipated wind tunnel flow conditions with significant margins/factors of safety. It is furthermore demonstrated that the SCF is more susceptible to aeroelastic instability than the SGF, which has implications for flight feasibility.

Similitude↗
NASA NTRS2023

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

This final report documents work performed by ATA Engineering, Inc., (ATA) to develop computational models and analyze the coupled fluid-structure response of two types of noise treatments applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The first treatment is a slat-gap filler (SGF), which closes the gap between the suction surfaces of a deployed slat and an aircraft main wing, and the second treatment is a slat-cove filler (SCF), which replaces the recirculating flow on the slat cove with a surface that promotes flow attachment. The representative airframe chosen for this work was NASA’s High-Lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs were assessed for their static aeroelastic deflection as well as their dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL-CSD) tools. Specifically, fluid-structure interaction (FSI) problems were solved computationally using the CFD solver Loci/CHEM and the NL-CSD solver Abaqus. As a part of the overall project, a similar capability was implemented using the CFD solver FUN3D coupled to Abaqus, although that work is documented in a separate report and that FSI framework was not used to analyze any of NASA’s SGF and SCF configurations. The technical approach consisted of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design was analyzed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability, whereas the SCF was analyzed in 2D only. SGF static aeroelastic response predictions focused on characterizing the deformed shape, with maximum displacements predicted to be on the order of magnitude of the technology element panel thickness. SGF dynamic aeroelastic response predictions used Partial Floquet analysis of the temporal evolution of selected nodal displacements to quantify the sign and magnitude of aeroelastic damping. Results suggest that the CRM-HL operating conditions would result in a dynamically stable response. The simulated dynamic pressure was also increased up to a factor of about four, and resulting responses suggest that predicted dynamic stability would be achieved with some margin.

Fluid Structure Interaction↗
NASA NTRSDate not supplied

Slat Noise Control Using a Slat Gap Filler

The leading edge slat of a high-lift system is one of the main noise contributors on many commercial aircraft during approach. This paper continues our previous studies on the gap filler for passive noise control on the 30P30N high-lift airfoil. An improved implementation of the gap filler was applied to minimize the effects of flow leakage encountered in the previous work, which resulted in spurious noise content in the far-field acoustic spectra. To evaluate the effect of passive flow control on the acoustics generated by the unsteady flow field, anechoic wind tunnel experiments are conducted on the two-dimensional, three-element high-lift airfoil with a gap filler mounted to the slat. The slat geometry modification associated with the gap filler alters the flow field in the cove region that dominates the generation of the acoustic field. A single angle of attack (훼푘=8◦) and three flow speeds corresponding to Reynolds numbersof푅푒푐=1.2푒6,1.5푒6, and1.71푒6are selected as the test conditions. Steady surface pressure measurements are conducted to assess the effect of the treatments on the overall lift. Acoustic array measurements are used to evaluate the influence of the gap filler on the radiated noise. Delay and Sum beamforming is applied to locate the noise sources on the model and to provide the integrated spectra. The gap filler is found to eliminate the narrowband peaks in the acoustic spectra and, also, to yield a 10 dB reduction in the broadband noise in comparison with the baseline case. Time-resolved Particle Image Velocimetry results show that the flow features are significantly altered with the presence of the gap filler, which leads to a more stable slat cove shear layer and, thus, to weaker pressure and velocity fluctuations.

Yang Zhang↗
NASA NTRSDate not supplied

Overview of Aeroacoustic Testing of the High-Lift Common Research Model

This paper presents an overview of the experimental data obtained in a 2020/2021 aeroacoustic test of the high-lift variant of the common research model. The breadth of the aerodynamic and acoustic measurements is highlighted along with some key results. Aerodynamic data were observed to be consistent with previous observations, and the acoustic measurements were repeatable once some background noise and shear layer issues were resolved. The primary purpose of the test was to evaluate the noise reduction potential of slat noise reduction devices, and a slat-gap filler was found to produce substantial noise reduction over a broad frequency range. The gap filler was designed to meet practical implementation considerations at full scale and constructed out of shape-memory alloys that would allow the slat to be articulated. However, additional structural testing will be required to demonstrate the performance of the gap filler during slat deployment and retraction. Over 3,500 test points were collected during the test, and only a small fraction of the experimental data has been processed in a preliminary manner. Nonetheless, the results presented demonstrate the quality of the dataset and reveal some insights about slat noise.

Aeroacoustics↗
NASA NTRSDate not supplied

Fully Coupled Aeroelastic Stability Analysis of Adaptive Shape Memory Alloy Structural Technologies for Airframe Noise Reduction

The objective of this work is the development of computational models and analysis of the coupled fluid-structure response of a slat gap filler (SGF) noise treatment applied to the leading-edge-slat component of a high-lift system typical of modern transport aircraft. The representative airframe chosen for this work is NASA’s High-lift Common Research Model (CRM-HL) in a baseline high-lift configuration. Superelastic shape memory alloys (SMAs) have been identified as enabling materials for these structural treatments. Since the technology elements rely upon having a highly reconfigurable structure, designs must be assessed for static aeroelastic deflection as well as dynamic aeroelastic stability using coupled computational fluid dynamics (CFD) and nonlinear computational structural dynamics (NL CSD) tools. The technical approach consists of solving for the flow field around the entire vehicle using a global CFD model, followed by extraction of relevant local subdomain data for CFD and NL-CSD co-simulations. The SGF design is assessed using both 2D and 3D co-simulations to predict quasi-static aeroelastic deformations and to assess dynamic aeroelastic stability.

Fluid structure interaction↗
NASA NTRSDate not supplied

Development of Slat-gap and Slat-cove Filler Treatments for Noise Reduction Assessment on the High Lift Common Research Model in the NASA LaRC 14x22

Airframe noise is an important issue during the approach and landing phases of flight because engines are throttled back, and airframe sources become an equal or greater contributor to environmental noise. The leading-edge slat component of the high-lift system for transport aircraft has been identified as a prominent source of airframe noise. Noise production mechanisms and potential treatments to mitigate airframe noise have been areas of active research for nearly three decades. Two promising technologies for slat noise reduction are the slat-gap filler (SGF) and slat-cove filler (SCF). Previous work was done using a 2D section of a transport class aircraft wing to demonstrate their feasibility via benchtop and computational models. A wind tunnel test campaign was recently undertaken to test the SGF and SCF technologies in a flight-like environment by installing dynamically scaled treatments on the 10%-scale High-Lift Common Research Model (CRM-HL), which is representative of a commercial twin-aisle transport aircraft. Advancement of the SGF and SCF technologies to overcome challenges of integration with 3D airframe structures, computational simulations of the CRM-HL predicting the aerodynamic and aeroacoustic performance and structural loads, and design of wind tunnel model hardware with features accommodating noise treatments were conducted in parallel. Details of innovations in the SGF and SCF technologies for 3D airframe feasibility will be described. The loads the treatments must sustain in flight and the influence of those loads on the design is also discussed. Finally, the design of wing leading-edge assemblies to treat the 10% CRM-HL with dynamically scaled SGF and SCF components is presented. The treatments were successfully tested in 2020/2021 providing a demonstration of leading-edge noise reduction using components that would allow slat articulation.

airframe noise reduction↗