The leading-edge slat of a high-lift wing is one of the main noise contributors during approach and landing. This paper describes an experimental investigation of the velocity field associated with multiple passive noise treatments, including slat-cusp extensions, a cove filler, and a gap filler, on a two-dimensional multi-element high-lift 30P30N airfoil. Previous work documented comparisons of both surface and far field pressure fluctuations in the presence of these devices with those for a baseline case at different flow conditions. However, important information related to the velocity fields was missing from the previous measurements, hindering our ability to elucidate the changes in the flow physics associated with the noise treatments. Therefore, two-component Particle Image Velocity has been used to investigate the influence of passive noise treatments on the flow fields. All measurements are taken at an effective, free-air angle of attack of 5.5 degrees and a stowed-chord-based Reynolds number of 1.71 × 10e6. The measurements show that the slat extensions shorten the slat-cove shear layer trajectory, resulting in reduced growth of disturbances within the slat-cove shear layer. This leads to a shift of tonal peaks to higher frequencies and a reduction in the tonal amplitudes. The gap filler blocks the flow path through the gap, causing the reattachment location to shift to the main wing leading edge lower surface. Consequently, the feedback loop associated with the flow-acoustic interaction in the baseline case is eliminated, and the turbulent kinetic energy in the slat-cove shear layer is significantly reduced. However, extensive flow separation is observed on the suction side of the gap filler, which does not eliminate the noise reduction benefit due to the gap filler, but does degrade the aerodynamic performance of the high-lift configuration. Finally, the overall flow field in the presence of the cove filler is similar to that in the baseline case at the design angle of attack, but the slat-cove shear layer is eliminated leading to a suppression of the cavity tones associated with the shear layer. This change accounts for the reduction in slat noise as measured in previous work.

Aeroacoustics↗

NASA NTRSDate not supplied

The Light Bender Concept for Power Distribution on a Lunar Base

Power generation and distribution is a challenge for a future lunar base. A promising concept for lunar power distribution is the light bender—a system that utilizes autonomously deployed mirrors to reflect sunlight to shaded regions on the lunar surface. The light bender system consists of two components: tandem reflector mirrors (TRM) which reflect sunlight to a permanently shaded region and the Cassegrain Fresnel distribution optics (CFDO) which collects the reflected light from the TRM and redirects light to local consumer nodes. This paper describes the light bender system concepts and the associated system analysis and technology development performed as part of a 2021 NASA Innovative Advanced Concepts (NIAC) phase I award.

Bradford Robertson↗

NASA NTRSDate not supplied

The Light Bender Concept for Power Distribution on a Lunar Base

Bradford Robertson↗

NASA NTRSDate not supplied

Effects of Porous Gap Fillers on 30P30N Leading-Edge SlatNoise. Part I: Surface Pressure and Acoustics

The leading edge slat of a high-lift system is one of the main contributors to airframe noise during approach. In a previous experimental study, we assessed the performance of an impermeable slat gap filler as a passive flow control device to reduce the slat noise associated with a two-dimensional, three-element high-lift airfoil. The present paper, the first of two parts,represents a follow-on investigation to assess the relative efficacy of permeable gap fillers thatallow successively higher amounts of flow to pass through the gap. To evaluate the influence of this passive flow control device on the acoustics generated by the unsteady flow near the slat, experiments are conducted in an anechoic wind tunnel by mounting a gap filler to the slat element of the two-dimensional 30P30N high-lift configuration. Measurements are performed at a single geometric angle of attack (𝛼𝑘=8◦) and three different flow speeds that correspond to Reynolds numbers of𝑅𝑒𝑐=1.2𝑒6,1.5𝑒6, and1.71𝑒6, respectively. Steady surface pressure measurements are used to gauge the influence of the permeable gap filler treatments on the overall lift. The effect of each treatment on the radiated noise is analyzed via acoustic array measurements, followed by delay-and-sum beamforming to locate the slat noise sources and to provide the integrated acoustic spectra. The porous gap fillers are found to eliminate the narrowband peaks in the acoustic spectra and, also, to yield a 10 dB reduction in the broadband noise in comparison with the baseline case with no gap filler. The porous gap filler with thelowest permeability acts similar to the impermeable gap filler examined previously. However, the aerodynamics and noise reduction both degrade with increasing permeability. An accompanying abstract describes the particle image velocimetry measurements of the flowfield within the slat cove and on either side of the permeable gap f

slat noise↗

NASA NTRSDate not supplied

Effects of Porous Gap Fillers on Leading-Edge Slat Noise of 30P30N. Part II: PIV Measurements

The leading edge slat of a high-lift system is one of the main contributors to the airframe noise during approach conditions. This paper, the second of two parts, continues our previous studies on the slat gap filler as a passive noise control device on the two-dimensional, 30P30N multielement airfoil. Whereas the earlier study was focused on the effects of an impermeable gap filler that completely blocks the flow through the gap, this follow-on assessment is devoted to permeable slat gap fillers that allow limited amounts of flow to pass through the gap. Part I of this two-part abstract described the aerodynamic and acoustic effects of the permeable gap fillers, as inferred from both the measurements of static and unsteady surface pressures and the microphone array data for the radiated noise. To understand the physical mechanism responsible for the noise reduction documented in Part I, as well as for the accompanying aerodynamic penalty due to the porous gap fillers, Particle Image Velocimetry (PIV) is used in this paper to measure the flow details in the slat-cove region of the 30P30N model. A single angle of attack (𝛼 = 5.5◦) and a chord based Reynolds number of 1.71𝑒6 are selected as the test conditions. The PIV results show that the slat flow features are significantly altered with the presence of the porous gap filler, resulting in a more stable slat-cove shear layer and, thus, reduced velocity fluctuations with a successive decrease in the permeability. The porous gap filler with the lowest permeability acts similar to the solid gap filler. However, flow separation is observed on the upper side of the porous interface, which leads to an aerodynamic performance penalty via a reduction in lift on the main wing.

slat noise↗