Search NASA⌕ Search

Engineering topics

Trowbridge, Tammy

Publications and source records attributed to Trowbridge, Tammy.

6 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Possible impacts of Mo chemical banding and second phase impurities on the irradiation behavior of monolithic U-10Mo fuels

This study investigated the microstructural behavior of both full-size and mini-size monolithic U-10Mo fuel plates irradiated to high burnup with a focus on the evolution of the second phase impurities in monolithic U-Mo using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and wavelength dispersive spectroscopy (WDS). Key indicators of possible mechanical and thermal compromise include cracks, large fission gas porosity, and interconnection of fission gas pores. For the fission densities evaluated in this work (3.5 × 10 21 fissions/cm 3 -5.1 × 10 21 fissions/cm 3 ), fine porosity can develop along the UC phase boundary; however, the size of the fission gas pores is no more than those observed in the U-Mo fuel phase. Further, other inclusions such as Si-rich second-phase impurities found in the as-fabricated microstructure were difficult to resolve post-irradiation because they can become overshadowed by porosity development in the fuel phase. Additionally, the presence of a Fe-rich sublayer formed in the Zr diffusion layer during fabrication remained enriched in the Zr layer in the irradiated U-10Mo microstructures near the U-Mo/Zr interface; however, based on the burnup assessed in this study the identified impurities did not appear to contribute to notable microstructural degradation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils

In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Investigation of constituent redistribution in U-Pu-Zr fuels and its dependence on varying Zr content

This contribution investigates fuel constituent segregation and fuel-cladding chemical interactions (FCCI) in three U-Pu-Zr fuel pins irradiated to ~11% burnup in Experimental Breeder Reactor-II as part of the X441 DP-1 experiment. In examined pins, Zr content ranged from 6 to 10 and 14 wt.%, while Pu concentration was constant at 19 wt.% Pu. The primary goal of the investigation was to determine the role Zr content plays in fuel performance and this manuscript provides assessment of both constituent redistribution and FCCI as a function of axial position. FCCI was observed in all pins, though no cladding failure was noted. Optical and scanning electron microscopy (SEM) results show that variation in Zr content alters the number and relative size of constituent redistribution zones in the fuel. For example, larger Zr-rich central regions and smaller U-rich intermediate regions were observed in 14 wt.% Zr fuels. More importantly, all examined fuels have four or more discrete constituent redistribution regions, where each region has dissimilar morphological features. The existence of four to six distinctive regions deviates from traditionally accepted three region redistribution model, highlights complexity of constituent redistribution in this metal fuel, and identifies the need to conduct additional studies using state-of-the-art instrumentation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Characterization Report for the MP-1 Experiment Fabrication Campaign (Rev.1)

This report covers the results of MP 1 fuel characterization analysis to provide a detailed understanding of the as-fabricated fuel that would be irradiated in the MP 1 (Mini-Plate 1) experiment. The work was performed at Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and Los Alamos National Laboratory (LANL). Characterization of the as-fabricated fuel was performed in accordance with Characterization Plan for the Fabrication of U 10Mo for the MP 1 Experiment, hereinafter the MP 1 Characterization Plan (MAQP 2016). Under the MP 1 Characterization Plan, fuel foils at different points in the foil fabrication process (e.g., hot rolled annealed, cold rolled annealed) were studied to understand the effect of various thermomechanical processes on the fuel microstructure. Samples were sent to each of the three organizations so that testing and analysis could be performed independently using similar equipment and a standardized set of measurement and analysis procedures. The MP 1 experiment will provide an opportunity to understand the effects of processing conditions on the final fuel microstructure, to compare independently obtained results, and achieve a three-way validation. PNNL characterized 28 uranium–10 wt% molybdenum (U 10Mo) samples. Six pieces/specimens from each sample/foil were sectioned, in accordance with the MP 1 Characterization Plan. Similarly, INL and LANL also examined 24 and 17 U 10Mo specimens, respectively. These total 69 samples consist of six types of MP 1 characterization foils fabricated by Babcock and Wilcox Technologies (BWXT) from ingots produced by the Y-12 National Security Complex: (a.) 0.047 in.-thick hot-rolled and annealed samples with and without Zr layers; (b.) 0.02 in.-thick cold-rolled and annealed samples with and without Zr layers; and (c.) 0.01 in.-thick cold-rolled and annealed samples with and without Zr layers. Microstructure, chemical composition, carbide morphology, U 10Mo foil thickness, Zr thickness, mechanical properties (microhardness), and density were evaluated in both longitudinal and transverse directions for foils of the three different thicknesses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Characterization Report for the MP-1 Experiment Fabrication Campaign

This report covers the results of MP 1 fuel characterization analysis to provide a detailed understanding of the as-fabricated fuel that would be irradiated in the MP 1 (Mini-Plate 1) experiment. The work was performed at Pacific Northwest National Laboratory (PNNL), Idaho National Laboratory (INL), and Los Alamos National Laboratory (LANL). Characterization of the as-fabricated fuel was performed in accordance with Characterization Plan for the Fabrication of U 10Mo for the MP 1 Experiment, hereinafter the MP 1 Characterization Plan (MAQP 2016). Under the MP 1 Characterization Plan, fuel foils at different points in the foil fabrication process (e.g., hot rolled annealed, cold rolled annealed) were studied to understand the effect of various thermomechanical processes on the fuel microstructure. Samples were sent to each of the three organizations so that testing and analysis could be performed independently using similar equipment and a standardized set of measurement and analysis procedures. The MP 1 experiment will provide an opportunity to understand the effects of processing conditions on the final fuel microstructure, to compare independently obtained results, and achieve a three-way validation. PNNL characterized 28 uranium–10 wt% molybdenum (U 10Mo) samples. Six pieces/specimens from each sample/foil were sectioned, in accordance with the MP 1 Characterization Plan. Similarly, INL and LANL also examined 24 and 17 U 10Mo specimens, respectively. These total 69 samples consist of six types of MP 1 characterization foils fabricated by Babcock and Wilcox Technologies (BWXT) from ingots produced by the Y-12 National Security Complex: • 0.047 in.-thick hot-rolled and annealed samples with and without Zr layers • 0.02 in.-thick cold-rolled and annealed samples with and without Zr layers • 0.01 in.-thick cold-rolled and annealed samples with and without Zr layers. Microstructure, chemical composition, carbide morphology, U 10Mo foil thickness, Zr thickness, mechanical properties (microhardness), and density were evaluated in both longitudinal and transverse directions for foils of the three different thicknesses.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗