Engineering topics

Tsai, C.-Y.

Publications and source records attributed to Tsai, C.-Y..

6 records

NASA NTRS2001

Scramjet Tests in a Shock Tunnel at Flight Mach 7, 10, and 15 Conditions

Tests of the Hyper-X scramjet engine flowpath have been conducted in the HYPULSE shock tunnel at conditions duplicating the stagnation enthalpy at flight Mach 7, 10, and 15. For the tests at Mach 7 and 10 HYPULSE was operated as a reflected-shock tunnel; at the Mach 15 condition, HYPULSE was operated as a shock-expansion tunnel. The test conditions matched the stagnation enthalpy of a scramjet engine on an aerospace vehicle accelerating through the atmosphere along a 1000 psf dynamic pressure trajectory. Test parameter variation included fuel equivalence ratios from lean (0.8) to rich (1.5+); fuel composition from pure hydrogen to mixtures of 2% and 5% silane in hydrogen by volume; and inflow pressure and Mach number made by changing the scramjet model mounting angle in the HYPULSE test chamber. Data sources were wall pressures and heat flux distributions and schlieren and fuel plume imaging in the combustor/nozzle sections. Data are presented for calibration of the facility nozzles and the scramjet engine model. Comparisons of pressure distributions and flowpath streamtube performance estimates are made for the three Mach numbers tested.

Rogers, R. C.↗

NASA NTRS2001

Hyper-X Mach 10 Engine Flowpath Development: Fifth Entry Test Conditions and Methodology

A series of Hyper-X Mach 10 flowpath ground tests are underway to obtain engine performance and operation data and to confirm and refine the flowpath design methods. The model used is a full-scale height, partial-width replica of the Hyper-X Research Vehicle propulsive flowpath with truncated forebody and aftbody. This is the fifth test entry for this model in the NASA-HYPULSE facility at GASL. For this entry the facility nozzle and model forebody were modified to better simulate the engine inflow conditions at the target flight conditions. The forebody was modified to be a wide flat plate with no flow fences, the facility nozzle Mach number was increased, and the model was positioned to be tested in a semi-direct-connect arrangement. This paper presents a review of the test conditions, model calibrations, and a description of steady flow confirmation. The test series included runs using hydrogen fuel, and a silane-in-hydrogen fuel mixture. Other test parameters included the model mounting angle (relative to the tunnel flow), and the test gas oxygen fraction to account for the presence of [NO] in the test gas at the M10 conditions.

Bakos, R. J.↗

NASA NTRS1999

The Mach 10 Component of NASA's Hyper-X Ground Test Program

The Mach 10 Hyper-X ground test program is described, in which experimental flowpath parametric testing is being done in the HYPULSE facility. This facility has been upgraded for this effort by adding a reflected-shock-tunnel operating mode to access test conditions at Mach 10 and below. A large test section and hypersonic nozzle have been installed to provide full-scale engine test capability and the instrumentation systems have been expanded. A model of the Hyper-X engine flowpath has been built for freejet testing in the shock tunnel at both Mach 7 and 10 flight conditions. The model has over 180 instrumentation ports, a pitot rake mountable at the engine inlet or exit, and optical windows for visualization of the isolator, combustor, and nozzle. Testing in HYPULSE has been completed at Mach 7 conditions to provide a link between pulse facility data and the large Hyper-X performance database that is being accumulated in long-duration facilities. Comparisons of Mach 7 data with computational predictions and with data recently acquired for an identical flowpath being tested in the NASA 8-foot High Temperature Tunnel are presented.

Bakos, R. J.↗

NASA NTRS1998

Three-Component Force Measurements on a Scramjet in a Reflected-Shock Tunnel

A three-component stress-wave force-balance for a large scramjet has been designed, calibrated and tested in the HYPULSE reflected shock tunnel at GASL Inc., New York. The scramjet model is over 3-foot long and weighs in excess of 90 Ibm. The stress-wave force-balance is comprised of three stress bars which are attached to the model. Calibration results indicate that the force balance responds well within about 1 ms and that the sensitivity of the balance to the distribution of load is not large. Results with and without fuel injection were obtained in the tunnel operated for Mach 7 and Mach 10 flight simulation. These tests showed the force-balance can resolve axial force increments due to combustion of about 40 lb in the presence of model lift forces of 500-700 lb.

Tsai, C.-Y.↗

NASA NTRS1980

Examination of group-velocity criterion for breakdown of vortex flow in a divergent duct

A group-velocity criterion for vortex breakdown implied by wave trapping theory is applied to vortex flows in a slightly divergent duct that exhibits breakdown. The group velocities for both symmetric (n = 0) and nonsymmetric (n = plus or - 1) modes of wave propagation are calculated for the experimental data. It is found that the flow ahead of the breakdown region is always supercritical and stable to these modes of disturbances. However, the flow field behind the breakdown region may be either supercritical or subcritical to the modes n = 0 and n = 1, and always supercritical to mode n = -1. The flow field behind this breakdown region is unstable to the asymmetric mode disturbance (n = 1) for a finite range of wavenumbers. The calculated frequencies of the unstable disturbances are in good agreement with the frequencies obtained from the experimental measurements.

Tsai, C.-Y.↗

NASA NTRS1977

The instability of the thin vortex ring of constant vorticity

A theoretical study indicating that vortex rings at moderate Reynolds numbers are unstable to azimuthal bending waves is presented. Only the case of a thin vortex ring with a core of constant vorticity in an inviscid flow is examined. The disturbance flow and the mean flow of the vortex ring are derived as asymptotic solutions near the core; the stability analysis is developed completely for a certain class of bending waves that are unstable on a line filament in the presence of strain. The vortex ring is found to be always unstable for at least two wavenumbers for which waves on a line filament of the same vorticity distribution would not rotate. Published experimental results are cited to support these conclusions.

Widnall, S. E.↗