Engineering topics

Tucker, George E.

Publications and source records attributed to Tucker, George E..

14 records

NASA NTRS2009

An Investigation of Rotorcraft Stability-Phase Margin Requirements in Hover

A cooperative study was performed to investigate the handling quality effects from reduced flight control system stability margins, and the trade-offs with higher disturbance rejection bandwidth (DRB). The piloted simulation study, perform on the NASA-Ames Vertical Motion Simulator, included three classes of rotorcraft in four configurations: a utility-class helicopter; a medium-lift helicopter evaluated with and without an external slung load; and a large (heavy-lift) civil tiltrotor aircraft. This large aircraft also allowed an initial assessment of ADS-33 handling quality requirements for an aircraft of this size. Ten experimental test pilots representing the U.S. Army, Marine Corps, NASA, rotorcraft industry, and the German Aerospace Center (DLR), evaluated the four aircraft configurations, for a range of flight control stability-margins and turbulence levels, while primarily performing the ADS-33 Hover and Lateral Reposition MTEs. Pilot comments and aircraft-task performance data were analyzed. The preliminary stability margin results suggest higher DRB and less phase margin cases are preferred as the aircraft increases in size. Extra care will need to be taken to assess the influence of variability when nominal flight control gains start with reduced margins. Phase margins as low as 20-23 degrees resulted in low disturbance-response damping ratios, objectionable oscillations, PIO tendencies, and a perception of an incipient handling qualities cliff. Pilot comments on the disturbance response of the aircraft correlated well to the DRB guidelines provided in the ADS-33 Test Guide. The A D-3S3 mid-term response-to-control damping ratio metrics can be measured and applied to the disturbance-response damping ratio. An initial assessment of LCTR yaw bandwidth shows the current Level 1 boundary needs to be relaxed to help account for a large pilot off-set from the c.g. Future efforts should continue to investigate the applicability/refinement of the current ADS-33 requirements to large vehicles, like an LCTR.

Blanken, Chris L.↗

NASA NTRS2006

In-Flight Validation of a Pilot Rating Scale for Evaluating Failure Transients in Electronic Flight Control Systems

Engineering development and qualification of a Research Flight Control System (RFCS) for the Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) JUH-60A has motivated the development of a pilot rating scale for evaluating failure transients in fly-by-wire flight control systems. The RASCAL RFCS includes a highly-reliable, dual-channel Servo Control Unit (SCU) to command and monitor the performance of the fly-by-wire actuators and protect against the effects of erroneous commands from the flexible, but single-thread Flight Control Computer. During the design phase of the RFCS, two piloted simulations were conducted on the Ames Research Center Vertical Motion Simulator (VMS) to help define the required performance characteristics of the safety monitoring algorithms in the SCU. Simulated failures, including hard-over and slow-over commands, were injected into the command path, and the aircraft response and safety monitor performance were evaluated. A subjective Failure/Recovery Rating (F/RR) scale was developed as a means of quantifying the effects of the injected failures on the aircraft state and the degree of pilot effort required to safely recover the aircraft. A brief evaluation of the rating scale was also conducted on the Army/NASA CH-47B variable stability helicopter to confirm that the rating scale was likely to be equally applicable to in-flight evaluations. Following the initial research flight qualification of the RFCS in 2002, a flight test effort was begun to validate the performance of the safety monitors and to validate their design for the safe conduct of research flight testing. Simulated failures were injected into the SCU, and the F/RR scale was applied to assess the results. The results validate the performance of the monitors, and indicate that the Failure/Recovery Rating scale is a very useful tool for evaluating failure transients in fly-by-wire flight control systems.

Kalinowski, Kevin F.↗

NASA NTRS2004

In-Flight Assessment of a Pursuit Guidance Display Format for Manually Flown Precision Instrument Approaches

In-flight evaluations of a pursuit guidance display system for manually flown precision instrument approaches were performed. The guidance system was integrated into the RASCAL JUH-60A Black Hawk helicopter. The applicability of the pursuit guidance disp1aFs to the operation of Runway Independent Aircraft (RIA) is made evident because the displays allow the pilot to fly a complex, multi-segment, descending, decelerating approach trajectory. The complex trajectory chosen for this in-flight assessment began from a downwind abeam position at 110 knots and was hand-flown to a 50 ft decision altitude at 40 knots using a rate-command/attitude-hold plus turn-coordination control system. The elements of the pursuit guidance format displayed on a 10-inch liquid crystal display (LCD) flat panel consisted of a flightpath vector and a "leader" aircraft as the pursuit guidance element. Approach guidance was based primarily on carrier-phase differential Global Positioning System (GPS) navigation, and secondarily on both medium accuracy inertial navigation unit states and air data computer states. Required Navigation Performance (RNP) concepts were applied to the construction of display elements such as lateral/vertical deviation indicators and a tunnel that indicated to the pilot, in real-time, the performance with respect to RNP error bounds. The results of the flight evaluations of the guidance display show that precise path control for operating within tight RNP boundaries (RNP 0.007NM/24ft for initial approach, RNP 0.008NM/19ft for intermediate approach, and RNP 0.002NM/9ft for final approach) is attainable with minimal to moderate pilot workload.

Moralez, Ernesto, III↗

NASA NTRS2001

Design and Testing of Flight Control Laws on the RASCAL Research Helicopter

Two unique sets of flight control laws were designed, tested and flown on the Army/NASA Rotorcraft Aircrew Systems Concepts Airborne Laboratory (RASCAL) JUH-60A Black Hawk helicopter. The first set of control laws used a simple rate feedback scheme, intended to facilitate the first flight and subsequent flight qualification of the RASCAL research flight control system. The second set of control laws comprised a more sophisticated model-following architecture. Both sets of flight control laws were developed and tested extensively using desktop-to-flight modeling, analysis, and simulation tools. Flight test data matched the model predicted responses well, providing both evidence and confidence that future flight control development for RASCAL will be efficient and accurate.

Frost, Chad R.↗

NASA NTRS2001

Flight Test Identification and Simulation of a UH-60A Helicopter and Slung Load

Helicopter slung-load operations are common in both military and civil contexts. Helicopters and loads are often qualified for these operations by means of flight tests, which can be expensive and time consuming. There is significant potential to reduce such costs both through revisions in flight-test methods and by using validated simulation models. To these ends, flight tests were conducted at Moffett Field to demonstrate the identification of key dynamic parameters during flight tests (aircraft stability margins and handling-qualities parameters, and load pendulum stability), and to accumulate a data base for simulation development and validation. The test aircraft was a UH-60A Black Hawk, and the primary test load was an instrumented 8- by 6- by 6-ft cargo container. Tests were focused on the lateral and longitudinal axes, which are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities; tests were conducted at airspeeds from hover to 80 knots. Using telemetered data, the dynamic parameters were evaluated in near real time after each test airspeed and before clearing the aircraft to the next test point. These computations were completed in under 1 min. A simulation model was implemented by integrating an advanced model of the UH-60A aerodynamics, dynamic equations for the two-body slung-load system, and load static aerodynamics obtained from wind-tunnel measurements. Comparisons with flight data for the helicopter alone and with a slung load showed good overall agreement for all parameters and test points; however, unmodeled secondary dynamic losses around 2 Hz were found in the helicopter model and they resulted in conservative stability margin estimates.

Cicolani, Luigi S.↗

NASA NTRS1999

Flight-Time Identification of a UH-60A Helicopter and Slung Load

This paper describes a flight test demonstration of a system for identification of the stability and handling qualities parameters of a helicopter-slung load configuration simultaneously with flight testing, and the results obtained. Tests were conducted with a UH-60A Black Hawk at speeds from hover to 80 kts. The principal test load was an instrumented 8 x 6 x 6 ft cargo container. The identification used frequency domain analysis in the frequency range to 2 Hz, and focussed on the longitudinal and lateral control axes since these are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities. Results were computed for stability margins, handling qualities parameters and load pendulum stability. The computations took an average of 4 minutes before clearing the aircraft to the next test point. Important reductions in handling qualities were computed in some cases, depending on control axis and load-sling combinations. A database, including load dynamics measurements, was accumulated for subsequent simulation development and validation.

Cicolani, Luigi S.↗

NASA NTRS1998

Flight-Time Identification of a UH-60A Helicopter and Slung Load

This paper describes a flight test demonstration of a system for identification of the stability and handling qualities parameters of a helicopter-slung load configuration simultaneously with flight testing, and the results obtained.Tests were conducted with a UH-60A Black Hawk at speeds from hover to 80 kts. The principal test load was an instrumented 8 x 6 x 6 ft cargo container. The identification used frequency domain analysis in the frequency range to 2 Hz, and focussed on the longitudinal and lateral control axes since these are the axes most affected by the load pendulum modes in the frequency range of interest for handling qualities. Results were computed for stability margins, handling qualities parameters and load pendulum stability. The computations took an average of 4 minutes before clearing the aircraft to the next test point. Important reductions in handling qualities were computed in some cases, depending, on control axis and load-slung combination. A database, including load dynamics measurements, was accumulated for subsequent simulation development and validation.

Cicolani, Luigi S.↗

NASA NTRS1996

The Use of Piloted Simulation for Civil Tiltrotor Integrated Cockpit Design

Ground-based flight simulators are receiving increased use in the design of civil aircraft. In addition to traditional simulation roles in support of cockpit control and display design, simulators are now used to develop new flight procedures and to assist in airport design. This is particularly true for the concept of a civil tiltrotor transport. This presentation summarizes recent simulation activity at NASA's Ames Research Center focused on the design requirements for the introduction of tiltrotor aircraft as economic vertical flight transports.

Decker, William A.↗

NASA NTRS1995

Conceptual Design of a Tiltrotor Transport Flight Deck

A tiltrotor transport has considerable potential as a regional transport, increasing the air transportation system capacity by off-loading conventional runways. Such an aircraft will have a flight deck suited to its air transportation task and adapted to unique urban vertiport operating requirements. Such operations are likely to involve steep, slow instrument approaches for vertical and extremely short rolling take-offs and landings. While much of a tiltrotor transport's operations will be in common with commercial fixed-wing operations, terminal area operations will impose alternative flight deck design solutions. Control systems, displays and guidance, and control inceptors must be tailored to both routine and emergency vertical flight operations. This paper will survey recent experience with flight deck design elements suitable to a tiltrotor transport and will propose a conceptual cockpit design for such an aircraft. A series of piloted simulations using the NASA Ames Vertical Motion Simulator have investigated cockpit design elements and operating requirements for tiltrotor transports operating into urban vertiports. These experiments have identified the need for a flight director or equivalent display guidance for steep final approaches. A flight path vector display format has proven successful for guiding tiltrotor transport terminal area operations. Experience with a Head-Up Display points to the need for a bottom-mounted display device to maximize its utility on steep final approach paths. Configuration control (flap setting and nacelle angle) requires appropriate augmentation and tailoring for civil transport operations, flown to an airline transport pilot instrument flight rules (ATP-IFR) standard. The simulation experiments also identified one thrust control lever geometry as inappropriate to the task and found at least acceptable results with the vertical thrust control lever of the XV-15. In addition to the thrust controller, the attitude control of a tiltrotor transport may be effected through an inceptor other than the current center sticks in the XV-15 and V-22. Simulation and flight investigations of side-stick control inceptors for rotorcraft, augmented by a 1985 flight test of a side-stick controller in the XV-15 suggest the potential of such a device in a transport cockpit.

Decker, William A.↗

NASA NTRS1994

Handling Qualities Influences on Civil Tiltrotor Terminal Operating Procedure Development

The potential for tiltrotor aircraft as civil transports has been well recognized. Realization of that potential requires development of operating procedures tailored to take advantage of the tiltrotor's capabilities, including thrust vectoring independent of body pitch attitude and good low-speed control. While the tiltrotor shares flight characteristics with both fixed wing airplanes and helicopters, it must convert between those flight modes, typically within the context of precise terminal operations. A series of piloted simulation experiments has been conducted on the NASA Ames Research Center Vertical Motion Simulator (VMS) to investigate the influence of tiltrotor cockpit design features on developing certification and operating criteria for civil tiltrotor transports. Handling qualities evaluations have shaped cockpit design guidelines and operating procedure development for a civil tiltrotor. In particular, four topics demonstrate the interplay of handling qualities and operations profile in the development of terminal operating procedures and cockpit or control equipment for a civil tiltrotor: conversion (airplane to helicopter mode), final approach path angle, operating profile speeds and speed changes (particularly under instrument conditions), and one engine inoperative operational considerations.

Decker, William A.↗

NASA NTRS1993

Piloting considerations for terminal area operations of civil tiltwing and tiltrotor aircraft

The existing body of research to investigate airworthiness, performance, handling, and operational requirements for STOL and V/STOL aircraft was reviewed for its applicability to the tiltrotor and tiltwing design concepts. The objective of this study was to help determine the needs for developing civil certification criteria for these aircraft concepts. Piloting tasks that were considered included configuration and thrust vector management, glidepath control, deceleration to hover, and engine failure procedures. Flight control and cockpit display systems that have been found necessary to exploit the low-speed operating characteristics of these aircraft are described, and beneficial future developments are proposed.

Hindson, William S.↗

NASA NTRS1993

Evaluation of two cockpit display concepts for civil tiltrotor instrument operations on steep approaches

A piloted simulation experiment was conducted using the NASA Ames Research Center Vertical Motion Simulator to evaluate two cockpit display formats designed for manual control on steep instrument approaches for a civil transport tiltrotor aircraft. The first display included a four-cue (pitch, roll, power lever position, and nacelle angle movement prompt) flight director. The second display format provided instantaneous flight path angle information together with other symbols for terminal area guidance. Pilots evaluated these display formats for an instrument approach task which required a level flight conversion from airplane-mode flight to helicopter-mode flight while decelerating to the nominal approach airspeed. Pilots tracked glide slopes of 6, 9, 15 and 25 degrees, terminating in a hover for a vertical landing on a 150 feet square vertipad. Approaches were conducted with low visibility and ceilings and with crosswinds and turbulence, with all aircraft systems functioning normally and were carried through to a landing. Desired approach and tracking performance was achieved with generally satisfactory handling qualities using either display format on glide slopes up through 15 degrees. Evaluations with both display formats for a 25 degree glide slope revealed serious problems with glide slope tracking at low airspeeds in crosswinds and the loss of the intended landing spot from the cockpit field of view.

Decker, William A.↗

NASA NTRS1991

Flying quality analysis and flight evaluation of a highly augmented combat rotorcraft

This paper discusses implications of digital flight control system design for rotorcraft and illustrates the analysis of the resulting handling qualities obtained with the Advanced Digital Optical Control System demonstrator in the context of the proposed new handling-qualities specification for rotorcraft. Topics covered are digital flight control design and analysis methods, flight testing techniques, handling-qualities evaluation results, and correlation of flight test results with analytical models and the proposed handling-qualities specification. The evaluation of the demonstrator system indicates desirable response characteristics based on equivalent damping and frequency, but undersirably large effective time delays (exceeding 240 ms in all axes). Piloted handling qualities are found to be desirable or adequate for all low, medium, and high pilot gain tasks, but handling qualities are inadequate for ultrahigh gain tasks such as slope and running landings. Correlation of these results with the proposed handling-qualities specification indicates good agreement for the bandwidth boundaries, but suggests the need for more stringent limits on allowable phase delay. Analytical models based on emulation (s-plane) techniques compare favorably with flight-extracted frequency-domain characteristics of the overall (end-to-end) system responses.

Tischler, Mark B.↗

NASA NTRS1988

Research On The CH-47B Helicopter

Report describes equipment added to, and research capabilities of CH-47B helicopter. Programmable symbol generator provides display formats for variety of missions - those of vertical-takeoff-and-landing aircraft and helicopters. Powerful general-purpose flight computer in operation. Computer programmable in high-level languages and supports research more efficiently. Flight-control software developed to improve capability of helicopter to perform simulations in flight.

Hilbert, Kathryn B.↗