Engineering topics

Turkel, Eli

Publications and source records attributed to Turkel, Eli.

At least 19 records

NASA NTRS2007

Simulation of a Synthetic Jet in Quiescent Air Using TLNS3D Flow Code

Although the actuator geometry is highly three-dimensional, the outer flowfield is nominally two-dimensional because of the high aspect ratio of the rectangular slot. For the present study, this configuration is modeled as a two-dimensional problem. A multi-block structured grid available at the CFDVAL2004 website is used as a baseline grid. The periodic motion of the diaphragm is simulated by specifying a sinusoidal velocity at the diaphragm surface with a frequency of 450 Hz, corresponding to the experimental setup. The amplitude is chosen so that the maximum Mach number at the jet exit is approximately 0.1, to replicate the experimental conditions. At the solid walls zero slip, zero injection, adiabatic temperature and zero pressure gradient conditions are imposed. In the external region, symmetry conditions are imposed on the side (vertical) boundaries and far-field conditions are imposed on the top boundary. A nominal free-stream Mach number of 0.001 is imposed in the free stream to simulate incompressible flow conditions in the TLNS3D code, which solves compressible flow equations. The code was run in unsteady (URANS) mode until the periodicity was established. The time-mean quantities were obtained by running the code for at least another 15 periods and averaging the flow quantities over these periods. The phase-locked average of flow quantities were assumed to be coincident with their values during the last full time period.

Vatsa, Veer N.↗

NASA NTRS2007

Convergence Acceleration of Runge-Kutta Schemes for Solving the Navier-Stokes Equations

The convergence of a Runge-Kutta (RK) scheme with multigrid is accelerated by preconditioning with a fully implicit operator. With the extended stability of the Runge-Kutta scheme, CFL numbers as high as 1000 can be used. The implicit preconditioner addresses the stiffness in the discrete equations associated with stretched meshes. This RK/implicit scheme is used as a smoother for multigrid. Fourier analysis is applied to determine damping properties. Numerical dissipation operators based on the Roe scheme, a matrix dissipation, and the CUSP scheme are considered in evaluating the RK/implicit scheme. In addition, the effect of the number of RK stages is examined. Both the numerical and computational efficiency of the scheme with the different dissipation operators are discussed. The RK/implicit scheme is used to solve the two-dimensional (2-D) and three-dimensional (3-D) compressible, Reynolds-averaged Navier-Stokes equations. Turbulent flows over an airfoil and wing at subsonic and transonic conditions are computed. The effects of the cell aspect ratio on convergence are investigated for Reynolds numbers between 5:7 x 10(exp 6) and 100 x 10(exp 6). It is demonstrated that the implicit preconditioner can reduce the computational time of a well-tuned standard RK scheme by a factor between four and ten.

Swanson, Roy C., Jr.↗

NASA NTRS2006

Simulation of Synthetic Jets in Quiescent Air Using Unsteady Reynolds Averaged Navier-Stokes Equations

We apply an unsteady Reynolds-averaged Navier-Stokes (URANS) solver for the simulation of a synthetic jet created by a single diaphragm piezoelectric actuator in quiescent air. This configuration was designated as Case 1 for the CFDVAL2004 workshop held at Williamsburg, Virginia, in March 2004. Time-averaged and instantaneous data for this case were obtained at NASA Langley Research Center, using multiple measurement techniques. Computational results for this case using one-equation Spalart-Allmaras and two-equation Menter's turbulence models are presented along with the experimental data. The effect of grid refinement, preconditioning and time-step variation are also examined in this paper.

Vatsa, Veer N.↗

NASA NTRS2003

Choice of Variables and Preconditioning for Time Dependent Problems

We consider the use of low speed preconditioning for time dependent problems. These are solved using a dual time step approach. We consider the effect of this dual time step on the parameter of the low speed preconditioning. In addition, we compare the use of two sets of variables, conservation and primitive variables, to solve the system. We show the effect of these choices on both the convergence to a steady state and the accuracy of the numerical solutions for low Mach number steady state and time dependent flows.

Turkel, Eli↗

NASA NTRS1997

Preconditioning for Numerical Simulation of Low Mach Number Three-Dimensional Viscous Turbomachinery Flows

A preconditioning scheme has been implemented into a three-dimensional viscous computational fluid dynamics code for turbomachine blade rows. The preconditioning allows the code, originally developed for simulating compressible flow fields, to be applied to nearly-incompressible, low Mach number flows. A brief description is given of the compressible Navier-Stokes equations for a rotating coordinate system, along with the preconditioning method employed. Details about the conservative formulation of artificial dissipation are provided, and different artificial dissipation schemes are discussed and compared. The preconditioned code was applied to a well-documented case involving the NASA large low-speed centrifugal compressor for which detailed experimental data are available for comparison. Performance and flow field data are compared for the near-design operating point of the compressor, with generally good agreement between computation and experiment. Further, significant differences between computational results for the different numerical implementations, revealing different levels of solution accuracy, are discussed.

Tweedt, Daniel L.↗

NASA NTRS1997

Multistage Schemes with Multigrid for Euler and Navier-Strokes Equations: Components and Analysis

A class of explicit multistage time-stepping schemes with centered spatial differencing and multigrids are considered for the compressible Euler and Navier-Stokes equations. These schemes are the basis for a family of computer programs (flow codes with multigrid (FLOMG) series) currently used to solve a wide range of fluid dynamics problems, including internal and external flows. In this paper, the components of these multistage time-stepping schemes are defined, discussed, and in many cases analyzed to provide additional insight into their behavior. Special emphasis is given to numerical dissipation, stability of Runge-Kutta schemes, and the convergence acceleration techniques of multigrid and implicit residual smoothing. Both the Baldwin and Lomax algebraic equilibrium model and the Johnson and King one-half equation nonequilibrium model are used to establish turbulence closure. Implementation of these models is described.

Swanson, R. C.↗

NASA NTRS1995

A far-field non-reflecting boundary condition for two-dimensional wake flows

Far-field boundary conditions for external flow problems have been developed based upon long-wave perturbations of linearized flow equations about a steady state far field solution. The boundary improves convergence to steady state in single-grid temporal integration schemes using both regular-time-stepping and local-time-stepping. The far-field boundary may be near the trailing edge of the body which significantly reduces the number of grid points, and therefore the computational time, in the numerical calculation. In addition the solution produced is smoother in the far-field than when using extrapolation conditions. The boundary condition maintains the convergence rate to steady state in schemes utilizing multigrid acceleration.

Danowitz, Jeffrey S.↗

NASA NTRS1994

Accurate finite difference methods for time-harmonic wave propagation

Finite difference methods for solving problems of time-harmonic acoustics are developed and analyzed. Multidimensional inhomogeneous problems with variable, possibly discontinuous, coefficients are considered, accounting for the effects of employing nonuniform grids. A weighted-average representation is less sensitive to transition in wave resolution (due to variable wave numbers or nonuniform grids) than the standard pointwise representation. Further enhancement in method performance is obtained by basing the stencils on generalizations of Pade approximation, or generalized definitions of the derivative, reducing spurious dispersion, anisotropy and reflection, and by improving the representation of source terms. The resulting schemes have fourth-order accurate local truncation error on uniform grids and third order in the nonuniform case. Guidelines for discretization pertaining to grid orientation and resolution are presented.

Harari, Isaac↗

NASA NTRS1994

Effect of artificial viscosity on three-dimensional flow solutions

Artificial viscosity is added either implicity or explicitly in practically every numerical scheme for suppressing spurious oscillations in the solution of fluid-dynamics equations. In the present central-difference scheme, artificial viscosity is added explicitly for suppressing high-frequency oscillations and achieving good convergence properties. The amount of artificial viscosity added is controlled through the use of preselected coefficients. In the standard scheme, scalar coefficients based on the spectral radii of the Jacobian of the convective fluxes are used. However, this can add too much viscosity to the slower waves. Hence, the use of matrix-valued coefficients, which give appropriate viscosity for each wave component, is suggested. With the matrix-valued coefficients, the central-difference scheme produces more accurate solutions on a given grid, particularly in the vicinity of shocks and boundary layers, while still maintaining good convergence properties.

Turkel, Eli↗

NASA NTRS1993

Pseudo-compressibility methods for the incompressible flow equations

Preconditioning methods to accelerate convergence to a steady state for the incompressible fluid dynamics equations are considered. The analysis relies on the inviscid equations. The preconditioning consists of a matrix multiplying the time derivatives. Thus the steady state of the preconditioned system is the same as the steady state of the original system. The method is compared to other types of pseudo-compressibility. For finite difference methods preconditioning can change and improve the steady state solutions. An application to viscous flow around a cascade with a non-periodic mesh is presented.

Turkel, Eli↗

NASA NTRS1993

High order accurate solutions of viscous problems

We consider a fourth order extension to MacCormack's scheme. The original extension was fourth order only for the inviscid terms but was second order for the viscous terms. We show how to modify the viscous terms so that the scheme is uniformly fourth order in the spatial derivatives. Applications are given to some boundary layer flows. In addition, for applications to shear flows the effect of the outflow boundary conditions are very important. We compare the accuracy of several of these different boundary conditions for both boundary layer and shear flows. Stretching at the outflow usually increases the oscillations in the numerical solution but the addition of a filtered sponge layer (with or without stretching) reduces such oscillations. The oscillations are generated by insufficient resolution of the shear layer. When the shear layer is sufficiently resolved then oscillations are not generated and there is less of a need for a nonreflecting boundary condition.

Hayder, M. E.↗

NASA NTRS1993

High order accurate solutions of viscous problems

Hayder, M. Ehtesham↗

NASA NTRS1993

Numerical Simulation of a High Mach Number Jet Flow

The recent efforts to develop accurate numerical schemes for transition and turbulent flows are motivated, among other factors, by the need for accurate prediction of flow noise. The success of developing high speed civil transport plane (HSCT) is contingent upon our understanding and suppression of the jet exhaust noise. The radiated sound can be directly obtained by solving the full (time-dependent) compressible Navier-Stokes equations. However, this requires computational storage that is beyond currently available machines. This difficulty can be overcome by limiting the solution domain to the near field where the jet is nonlinear and then use acoustic analogy (e.g., Lighthill) to relate the far-field noise to the near-field sources. The later requires obtaining the time-dependent flow field. The other difficulty in aeroacoustics computations is that at high Reynolds numbers the turbulent flow has a large range of scales. Direct numerical simulations (DNS) cannot obtain all the scales of motion at high Reynolds number of technological interest. However, it is believed that the large scale structure is more efficient than the small-scale structure in radiating noise. Thus, one can model the small scales and calculate the acoustically active scales. The large scale structure in the noise-producing initial region of the jet can be viewed as a wavelike nature, the net radiated sound is the net cancellation after integration over space. As such, aeroacoustics computations are highly sensitive to errors in computing the sound sources. It is therefore essential to use a high-order numerical scheme to predict the flow field. The present paper presents the first step in a ongoing effort to predict jet noise. The emphasis here is in accurate prediction of the unsteady flow field. We solve the full time-dependent Navier-Stokes equations by a high order finite difference method. Time accurate spatial simulations of both plane and axisymmetric jet are presented. Jet Mach numbers of 1.5 and 2.1 are considered. Reynolds number in the simulations was about a million. Our numerical model is based on the 2-4 scheme by Gottlieb & Turkel. Bayliss et al. applied the 2-4 scheme in boundary layer computations. This scheme was also used by Ragab and Sheen to study the nonlinear development of supersonic instability waves in a mixing layer. In this study, we present two dimensional direct simulation results for both plane and axisymmetric jets. These results are compared with linear theory predictions. These computations were made for near nozzle exit region and velocity in spanwise/azimuthal direction was assumed to be zero.

Hayder, M. Ehtesham↗

NASA NTRS1993

Numerical simulations of a high Mach number jet flow

The present 2D simulations of plane and axisymmetric jets, which are relevant to current efforts to suppress the jet exhaust noise of prospective high-speed civil transports, were conducted by solving full Navier-Stokes equations by means of a high-order finite-difference scheme. The results obtained, which were able to generate the correct mode shape after an adjustment region of about 10 diameters, are in good agreement with linear-theory predictions of the growth of instability waves.

Hayder, M. E.↗

NASA NTRS1992

On central-difference and upwind schemes

A class of numerical dissipation models for central-difference schemes constructed with second- and fourth-difference terms is considered. The notion of matrix dissipation associated with upwind schemes is used to establish improved shock capturing capability for these models. In addition, conditions are given that guarantee that such dissipation models produce a Total Variation Diminishing (TVD) scheme. Appropriate switches for this type of model to ensure satisfaction of the TVD property are presented. Significant improvements in the accuracy of a central-difference scheme are demonstrated by computing both inviscid and viscous transonic airfoil flows.

Swanson, R. C.↗

NASA NTRS1992

Mappings and accuracy for Chebyshev pseudo-spectral approximations

The effect of mappings on the approximation, by Chebyshev collocation, of functions which exhibit localized regions of rapid variation is studied. A general strategy is introduced whereby mappings are adaptively constructed which map specified classes of rapidly varying functions into low order polynomials which can be accurately approximated by Chebyshev polynomial expansions. A particular family of mappings constructed in this way is tested on a variety of rapidly varying functions similar to those occurring in approximations. It is shown that the mapped function can be approximated much more accurately by Chebyshev polynomial approximations than in physical space or where mappings constructed from other strategies are employed.

Bayliss, Alvin↗

NASA NTRS1991

Extension of multigrid methodology to supersonic/hypersonic 3-D viscous flows

A multigrid acceleration technique developed for solving 3-D Navier-Stokes equations for subsonic/transonic flows was extended to supersonic/hypersonic flows. An explicit multistage Runge-Kutta type of time stepping scheme is used as the basic algorithm in conjunction with the multigrid scheme. Solutions were obtained for a blunt conical frustum at Mach 6 to demonstrate the applicability of the multigrid scheme to high speed flows. Computations were performed for a generic High Speed Civil Transport configuration designed to cruise at Mach 3. These solutions show both the efficiency and accuracy of the present scheme for computing high speed viscous flows over configurations of practical interest.

Vatsa, Veer N.↗

NASA NTRS1991

Asynchronous and corrected-asynchronous numerical solutions of parabolic PDES on MIMD multiprocessors

A major problem in achieving significant speed-up on parallel machines is the overhead involved with synchronizing the concurrent process. Removing the synchronization constraint has the potential of speeding up the computation. The authors present asynchronous (AS) and corrected-asynchronous (CA) finite difference schemes for the multi-dimensional heat equation. Although the discussion concentrates on the Euler scheme for the solution of the heat equation, it has the potential for being extended to other schemes and other parabolic partial differential equations (PDEs). These schemes are analyzed and implemented on the shared memory multi-user Sequent Balance machine. Numerical results for one and two dimensional problems are presented. It is shown experimentally that the synchronization penalty can be about 50 percent of run time: in most cases, the asynchronous scheme runs twice as fast as the parallel synchronous scheme. In general, the efficiency of the parallel schemes increases with processor load, with the time level, and with the problem dimension. The efficiency of the AS may reach 90 percent and over, but it provides accurate results only for steady-state values. The CA, on the other hand, is less efficient, but provides more accurate results for intermediate (non steady-state) values.

Amitai, Dganit↗