Skip to content

Engineering topics

Turnbull, D.

Publications and source records attributed to Turnbull, D..

At least 19 records

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Applications of a Rayleigh-Taylor model to direct-drive laser fusion

Here, this paper presents a simple physics-based model for the interpretation of key metrics in laser direct drive. The only input parameters required are target scale, in-flight aspect ratio, and beam-to-target radius, and the importance of each has been quantified with a tailored set of cryogenic implosion experiments. These analyses lead to compact and accurate predictions of the fusion yield and areal density as a function of hydrodynamic stability, and suggest new ways to take advantage of direct drive. To provide examples, we will discuss how the inferred mix width behaves relative to theory, then show how it could be exploited to perform a direct drive implosion with a Lawson metric or Χ no α of 0.24 ± 0.02—using a novel parameter space at high velocities and beam radii on the OMEGA laser—that projects to ignition at a laser energy ≤2.0 MJ.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Persistent Hot-Spot Mix in Cryogenic Direct-Drive Fusion Experiments

We show that an x-ray emission signature associated with acceleration phase mass injection correlates with poor experimental hot-spot convergence and a reduced neutron production relative to expectations. It is shown that with increased target mass as well as with higher-design adiabats, this signature is reduced, whereas with increased debris on the target the signature is increased. Here, we estimate that the vapor region in typical best designs may have up to 2x the assumed hydrogen mass at the start of deceleration.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Demonstration of a hydrodynamically equivalent burning plasma in direct-drive inertial confinement fusion

Focussing laser light onto the surface of a small target filled with deuterium and tritium implodes it and leads to the creation of a hot and dense plasma, in which thermonuclear fusion reactions occur. In order for the plasma to become self-sustaining, the heating of the plasma must be dominated by the energy provided by the fusion reactions—a condition known as a burning plasma. A metric for this is the generalized Lawson parameter, where values above around 0.8 imply a burning plasma. Here, we report on hydro-equivalent scaling of experimental results on the OMEGA laser system and show that these have achieved core conditions that reach a burning plasma when the central part of the plasma, the hotspot, is scaled in size by at least a factor of 3.9 ± 0.10, which would require a driver laser energy of at least 1.7 ± 0.13 MJ. In addition, we hydro-equivalently scale the results to the 2.15 MJ of laser energy available at the National Ignition Facility and find that these implosions reach 86% of the Lawson parameter required for ignition. Furthermore, our results support direct-drive inertial confinement fusion as a credible approach for achieving thermonuclear ignition and net energy in laser fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

Demonstration of hot-spot fuel gain exceeding unity in direct-drive inertial confinement fusion implosions

Irradiating a small capsule containing deuterium and tritium fuel directly with intense laser light causes it to implode, which creates a plasma hot enough to initiate fusion reactions between the fuel nuclei. Here we report on such laser direct-drive experiments and observe that the fusion reactions produce more energy than the amount of energy in the central so-called hot-spot plasma. This condition is identified as having a hot-spot fuel gain greater than unity. A hot-spot fuel gain of around four was previously accomplished at the National Ignition Facility in indirect-drive inertial confinement fusion experiments where the capsule is irradiated by X-rays. In that case, up to 1.9 MJ of laser energy was used, but in contrast, our experiments on the OMEGA laser system require as little as 28 kJ. As the hot-spot fuel gain is predicted to grow with laser energy and target size, our work establishes the direct-drive approach to inertial fusion as a promising path towards burning and ignited plasmas in the laboratory. Additionally, we report a record (direct-drive) fusion yield of 0.9 kJ on OMEGA, which we achieved with thin-ice deuterium–tritium liner targets.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Cross-beam energy transfer in conditions relevant to direct-drive implosions on OMEGA

In cross-beam energy transfer (CBET), the interference of two laser beams ponderomotively drives an ion-acoustic wave that coherently scatters light from one beam into the other. This redirection of laser beam energy can severely inhibit the performance of direct-drive inertial confinement fusion (ICF) implosions. To assess the role of nonlinear and kinetic processes in direct-drive-relevant CBET, the energy transfer between two laser beams in the plasma conditions of an ICF implosion at the OMEGA laser facility was modeled using particle-in-cell simulations. For typical laser beam intensities, the simulations are in excellent agreement with linear kinetic theory, indicating that nonlinear processes do not play a role in direct-drive implosions. At higher intensities, CBET can be modified by pump depletion, backward stimulated Raman scattering, or ion trapping, depending on the plasma density.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Inverse Bremsstrahlung Absorption

Inverse bremsstrahlung absorption was measured based on transmission through a finite-length plasma that was thoroughly characterized using spatially resolved Thomson scattering. Expected absorption was then calculated using the diagnosed plasma conditions while varying the absorption model components. To match data, it is necessary to account for: (1) the Langdon effect; (2) laser-frequency (rather than plasma-frequency) dependence in the Coulomb logarithm, as is typical of bremsstrahlung theories but not transport theories; and (3) a correction due to ion screening. Radiation-hydrodynamic simulations of inertial confinement fusion implosions have to date used a Coulomb logarithm from the transport literature and no screening correction. Here, we anticipate that updating the model for collisional absorption will substantially revise our understanding of laser-target coupling for such implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Ray-based cross-beam energy transfer modeling for broadband lasers

Broadband lasers have the potential to mitigate cross-beam energy transfer (CBET) in direct-drive inertial confinement fusion (ICF) experiments. Furthermore, a quantitative assessment of the bandwidth required for CBET mitigation necessitates the development of broadband ray-based CBET models that can be implemented in the radiation-hydrodynamic codes that are used to design ICF experiments. Two different approaches to broadband ray-based CBET modeling (discrete and fixed spectrum) are developed and compared to wave-based calculations. Both approaches give good agreement with wave-based calculations in ICF-relevant configurations. Full-scale 3D calculations show that the bandwidth required for adequate CBET mitigation increases with increasing scale and drive intensity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Reaching a burning plasma and ignition using smaller capsules/ Hohlraums , higher radiation temperatures, and thicker ablator/ice on the national ignition facility

In indirect-drive implosions, the final core hot spot energy and pressure and, hence, neutron yield attainable in 1D increase with increasing laser peak power and, hence, radiation drive temperature at the fixed capsule and Hohlraum size. Here we present simple analytic scalings validated by 1D simulations that quantify the improvement in performance and use this to explain existing data and simulation trends. Extrapolating to the 500 TW National Ignition Facility peak power limit in a low gas-fill 5.4 mm diameter Hohlraum based on existing high adiabat implosion data at 400 TW, 1.3 MJ and 1 × 10 16 yield, we find that a 2–3 × 10 17 yield (0.5–0.7 MJ) is plausible using only 1.8 MJ of laser energy. Based on existing data varying deuterium–tritium (DT) fuel thickness and dopant areal density, further improvements should be possible by increasing DT fuel areal density, and hence confinement time and yield amplification.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1987

Microstructures of undercooled germanium droplets

Undercoolings at crystal nucleation onset of liquid Ge droplets are measured and the microstructures of the droplets are examined. Undercooling values ranging from 150-415 + or 20 C were obtained. It is observed that for the samples undercooled less than 300 C prior to solidification the grain size was greater than 100 microns; for samples undercooled between 300-400 C the grain size was between 50-100 microns; and for samples undercooled greater than 400 C the grain size was 10-20 microns. Consideration is given to dendritic growth and interfacial undercooling. It is noted that there is a correlation between undercooling and as-crystallized grain structure.

Devaud, G.↗

NASA NTRS1985

Melting of Ni40Pd40P20 glass

Upon reheating, most glassy metal alloys crystallize at a temperature not far removed from the glass temperature Tg and far below the liquidus temperature T1. It has been reported by Kui et al. (1984) that the alloy Ni40Pd40P20, which exhibits a scaled glass temperature of about 0.68, has been melt quenched, under a flux of dehydrated B2O3, to a glass at rates as low as 1 deg/s. Here some specimens of this alloy, when similarly fluxed during reheating, have been reheated to temperatures within 50 deg of T1 and 280 deg above Tg at rates of about 2.5 deg/s, and then cooled again to Tg, without crystallization. From this behavior it is inferred that the steady frequency of homogeneous nucleation of crystals in the alloy is less than 0.1/cu cm s.

Kui, H. W.↗

NASA NTRS1985

Undercooling of molten silicon

Droplets of uncoated molten Si(0.4-0.8 mm diameter) have been undercooled 250 C. Ge droplets of similar size have been undercooled 280 C in a B2O3 flux. The observed nucleation onset temperatures of both Si and Ge droplets are at or below the predicted amorphous phase melting temperatures T(al). The solidified structures were polycrystalline. The nucleation frequency I, calculated from the Si data (20,000/cu cm s at 240 + or - 20 C undercooling), should be an upper limit of the homogeneous nucleation frequency of the crystal phase, since it has not been established that nucleation was homogeneous in these experiments. However, this limiting I for Si indicates that homogeneous nucleation of crystal would not become appreciable in laser pulsing experiments until the liquid Si is undercooled to well below T(al).

Devaud, G.↗

NASA NTRS1984

Formation of bulk metallic glass by fluxing

Bulk specimens (0.4-4 g mass) of the alloy Pd40Ni40P20 have been undercooled consistently to the glass state, with no detectable superficial crystallinity, in a molten flux of dehydrated boron oxide. The minimum dimension of the most massive glass specimen, so formed, was 1.0 cm. The absence of crystallinity in the specimens was confirmed by X-ray diffraction, scanning electron microscopy, and calorimetry.

Kui, H. W.↗

NASA NTRS1984

The undercooling of liquids

The formation by melt quenching of such metastable structures as glassy or microcrystalline solids and highly supersaturated solutions is made possible by the extreme resistance of most melts to homophase crystal nucleation at deep undercooling. This nucleation resistance contrasts sharply with the very low kinetic resistance to the movement of crystal-melt interfaces, once formed, in metals and other fluid systems at even minute undercooling. The methods of nucleation study which have proven especially effective in bypassing nucleation by heterophase impurities thereby exposing the high resistance of melts to homophase nucleation may be summarized as follows: observation of the crystallization behavior of dispersed small droplets; drop tube experiments in which liquid drops solidify, under containerless conditions, during their fall in the tube; and observation of the crystallization of bulk specimens immersed in fluxes chosen to dissolve or otherwise deactivate (e.g., by wetting) heterophase nucleants. This method has proven to be remarkably effective in deactivating such nucleants in certain pure metals.

Turnbull, D.↗

NASA NTRS1982

Bulk formation of a metallic glass - Pd40Ni40P20

Molten spheroids of Pd40Ni40P20, of up to 0.53-cm minor diameter, were slowly cooled (1.4 K/s) on a fused silica surface under 10 to the -6 torr vacuum to a form which was entirely glassy except for some superficial crystallinity comprising less than 0.5% of the volume. The occurrence of crystallization was eliminated by subjecting the specimens to surface etching followed by a succession of heating and cooling cycles. The absence of crystallization in bulk was confirmed by X-ray diffraction, transmission electron microscopy, and calorimetry. Using the last technique, the heat of crystallization of the glass was measured to be 5.3 + or - 0.3 kJ/g atom.

Drehman, A. J.↗

NASA NTRS1982

Crystal nucleation in glass-forming alloy and pure metal melts under containerless and vibrationless conditions

The undercooling behavior of large spheroids of Pd40Ni40P40 was investigated. By surface etching, supporting the specimens on a fused silica substrate, and successive heating and cooling, crystallization can be eliminated, presumable due to the removal of surface heterogeneities. By this method samples up to 3.2g with a 0.53 mm minor diameter, were made entirely glassy, except for some superficial crystals comprising less than 0.5% of the volume. These experiments show that a cooling rate of approximately 1 K/sec is adequate to avoid copious homogeneous nucleation in the alloy, and that by eliminating or reducing the effectiveness of heterogeneous nucleation sites, it is possible to form bulk samples of this metallic glass with virtually unlimited dimensions.

Spaepen, F.↗

NASA NTRS1982

Crystal nucleation in Pd-Si alloys

A study of the crystal phase nucleation in undercooled droplets of Pd-Si alloys with composition near the Pd(84.5)Si(15.5) eutectic composition is reported. Molten droplets are released at the top of a drop tube and solidify (to either a crystalline or glassy state) during descent. This provides a containerless (and nearly gravity free) environment so that nucleation due to container walls or vibrations is eliminated. It is found that crystallization, due to homogeneous nucleation, is bypassed in droplets of 1 mm diameter when cooled at 760 K/sec. From this an upper limit of the homogeneous nucleation rate is estimated. Results are compared with a previously published study of nucleation in 0.06 mm to 0.33 mm diameter droplets, which indicated that nucleation results from heterogeneous surface nucleation and that the number of these nuclei is dependent on the atmosphere in the drop tube.

Drehman, A. J.↗

NASA NTRS1980

The mechanism of growth of quartz crystals into fused silica

It is proposed that the growth of quartz crystals into fused silica is effected by a mechanism involving the breaking of an Si-O bond and its association with an OH group, followed by cooperative motion of the nonbridging oxygen and the hydroxyl group which results in the crystallization of a row of several molecules along a crystalline-amorphous interfacial ledge. This mechanism explains, at least qualitatively, all the results of the earlier experimental study of the dependence of quartz crystal growth upon applied pressure: large negative activation volume; single activation enthalpy below Si-O bond energy; growth velocity constant in time, proportional to the hydroxyl and chlorine content, decreasing with increasing degree of reduction, and enhanced by nonhydrostatic stresses; lower pre-exponential for the synthetic than for the natural silica.

Fratello, V. J.↗

NASA NTRS1980

Dependence of growth rate of quartz in fused silica on pressure and impurity content

The effects of pressure, temperature, and some variations in impurity content on the growth rate u of quartz into fused silica were measured. Under all conditions the growth rate was interface controlled and increased exponentially with pressure with an activation volume averaging -21.2 cu cm/mole. The activation enthalpy for all specimens is extrapolated to a zero pressure value of 64 kcal/mole, within the experimental uncertainty. At a given stoichiometry the effect of hydroxyl content on growth rate is described entirely by a linear term C(OH) in the prefactor of the equation for the growth rate. The effect of chlorine impurity can be described similarly. Also u is increased as the ideal stoichiometry is approached from the partially reduced state.

Fratello, V. J.↗