Engineering topics

Turriziani, R. V.

Publications and source records attributed to Turriziani, R. V..

6 records

NASA NTRS1985

Propulsion evaluation for orbit-on-demand vehicles

Future earth-to-orbit vehicles may be required to reach orbit within hours or even minutes of a decision. A study has been conducted to consider vehicles with such a capability. In Phase I of the study, 11 vehicles were designed to deploy 5000 lb to a polar orbit. Changes in the designs were examined parametrically for increased on-orbit maneuvers, increased payload, and other mission variations. Based on the results, two concepts were selected for Phase II design work: a vertical-takeoff, two-stage system and a horizontal-takeoff, two-stage system with an airbreathing subsonic first stage. The results of several propulsion evaluations are presented, including liftoff thrust-to-weight effects, dual-fuel propulsion for a horizontal-takeoff concept, and the effect of using fluorine.

Martin, J. A.↗

NASA NTRS1980

Preliminary design characteristics of a subsonic business jet concept employing an aspect ratio 25 strut braced wing

The advantages of replacing the conventional wing on a transatlantic business jet with a larger, strut braced wing of aspect ratio 25 were evaluated. The lifting struts reduce both the induced drag and structural weight of the heavier, high aspect ratio wing. Compared to the conventional airplane, the strut braced wing design offers significantly higher lift to drag ratios achieved at higher lift coefficients and, consequently, a combination of lower speeds and higher altitudes. The strut braced wing airplane provides fuel savings with an attendant increase in construction costs.

Turriziani, R. V.↗

NASA NTRS1979

Sensitivity study for a remotely piloted microwave-powered sailplane used as a high-altitude observation

The sensitivity of several performance characteristics of a proposed design for a microwave-powered, remotely piloted, high-altitude sailplane to changes in independently varied design parameters was investigated. Results were expressed as variations from baseline values of range, final climb altitude and onboard storage of radiated energy. Calculated range decreased with increases in either gross weight or parasite drag coefficient; it also decreased with decreases in lift coefficient, propeller efficiency, or microwave beam density. The sensitivity trends for range and final climb altitude were very similar. The sensitivity trends for stored energy were reversed from those for range, except for decreasing microwave beam density. Some study results for single parameter variations were combined to estimate the effect of the simultaneous variation of several parameters: for two parameters, this appeared to give reasonably accurate results.

Turriziani, R. V.↗

NASA NTRS1979

Evaluation of a long-endurance-surveillance remotely-piloted vehicle with and without laminar flow control

Two aircraft were evaluated, using a derated TF34-GE-100 turbofan engine one with laminar flow control (LFC) and one without. The mission of the remotely piloted vehicles (RPV) is one of high-altitude loiter at maximum endurance. With the LFC system maximum mission time increased by 6.7 percent, L/D in the loiter phase improved 14.2 percent, and the minimum parasite drag of the wing was reduced by 65 percent resulting in a 37 percent reduction for the total airplane. Except for the minimum parasite drag of the wing, the preceding benefits include the offsetting effects of weight increase, suction power requirements, and drag of the wing-mounted suction pods. In a supplementary study using a scaled-down, rather than derated, version of the engine, on the LFC configuration, a 17.6 percent increase in mission time over the airplane without LFC and an incremental time increase of 10.2 percent over the LFC airplane with derated engine were attained. This improvement was due principally to reductions in both weight and drag of the scaled engine.

Turriziani, R. V.↗

NASA NTRS1978

Preliminary design characteristics of a subsonic business jet concept employing laminar flow control

Aircraft configurations were developed with laminar flow control (LFC) and without LFC. The LFC configuration had approximately eleven percent less parasite drag and a seven percent increase in the maximum lift-to drag ratio. Although these aerodynamic advantages were partially offset by the additional weight of the LFC system, the LFC aircraft burned from six to eight percent less fuel for comparable missions. For the trans-atlantic design mission with the gross weight fixed, the LFC configuration would carry a greater payload for ten percent fuel per passenger mile.

Turriziani, R. V.↗

NASA NTRS1978

Design of a large span-distributed load flying-wing cargo airplane with laminar flow control

A design study was conducted to add laminar flow control to a previously design span-distributed load airplane while maintaining constant range and payload. With laminar flow control applied to 100 percent of the wing and vertical tail chords, the empty weight increased by 4.2 percent, the drag decreased by 27.4 percent, the required engine thrust decreased by 14.8 percent, and the fuel consumption decreased by 21.8 percent. When laminar flow control was applied to a lesser extent of the chord (approximately 80 percent), the empty weight increased by 3.4 percent, the drag decreased by 20.0 percent, the required engine thrust decreased by 13.0 percent, and the fuel consumption decreased by 16.2 percent. In both cases the required take-off gross weight of the aircraft was less than the original turbulent aircraft.

Lovell, W. A.↗