Search NASA⌕ Search

Engineering topics

Ulsh, Michael

Publications and source records attributed to Ulsh, Michael.

48 records · Page 3

Technical Assistance in Fabrication and Testing of MEAs: Cooperative Research and Development Final Report

Altergy's fuel cell cost is highly dependent on expensive purchased membrane electrode assemblies (MEAs), which amount to 42¢/watt in a 5kW system. In order to better compete with other power solutions, the company has identified an MEA breakthrough cost of 20¢/watt to unlock new, major markets for its fuel cell products. Since Altergy presently does not have an accurate cost model for the real costs of these MEAs, it is difficult to know whether the company goal is achievable. Altergy seeks to leverage NREL expertise to reduce cost and improve performance for Altergy's fuel cell products. The objective of this Small Business Voucher (SBV) project therefore will be for NREL and Altergy to work together in three major task areas: 1) demonstrating the fabrication of MEAs at NREL using NREL non-proprietary methods, to the intent of potentially fabricating MEAs at Altergy to reduce product costs; and, 2) creating a cost model to assist Altergy in manufacturing decisions.

30 DIRECT ENERGY CONVERSION↗

FY2017 annual report: Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Consortium Project

The following report provides a description of the program structure and technical accomplishments made during FY 2017 to overcome challenges for expanding use of R2R technologies and processing for clean energy applications. Technologies are under development that enable enhanced manufacturing of battery electrodes, fuel cells and water separation membranes that take advantage of advancements in new functional materials. Data mining, visualization, modeling and simulation for the materials, technologies and processes being developed allow for improvements in R2R manufacturing applications. This report documents the research conducted by four DOE national laboratories as a consortium in collaboration with industry partnerships. The research is directly applicable to AMM strategies that apply the National Science and Technology Council’s Materials Genome Initiative (NSTC 2011) approach to enhance the performance of battery, fuel cell and water membrane materials. This effort supports building the foundation of technologies, processes and a U.S. manufacturing base that will enable an order of magnitude in shorter process development cycles with the pathway for initial commercialization within months instead of years.

36 MATERIALS SCIENCE↗

Utilizing a Segmented Fuel Cell to Study the Effects of Electrode Coating Irregularities on PEM Fuel Cell Initial Performance

An understanding of the impact of coating irregularities on beginning of life polymer electrolyte fuel cell (PEMFC) performance is essential to develop and establish manufacturing tolerances for its components. Coating irregularities occurring in the fuel cell electrode can either possess acceptable process variations or potentially harmful defects. A segmented fuel cell (SFC) is employed to understand how 100% catalyst reduction irregularities ranging from 0.125 to 1 cm 2 in the cathode electrode of a 50 cm 2 sized cell impact spatial and total cell performance at dry and wet humidification conditions. Here, by analyzing the data in a differential format the local performance effects of irregularity sizes down to 0.25 cm 2 were detected in the current distribution of the cell. Slight total cell performance impacts, due to irregularity sizes of 0.5 and 1 cm 2 , were observed under dry operation and high current densities.

30 DIRECT ENERGY CONVERSION↗

Material-Process-Performance Relationships for Roll-to-Roll Coated PEM Electrodes

Roll-to-roll (R2R) coating is the most economical and highest throughput method for producing fuel cell electrodes. R2R coating encompasses many different methodologies to create uniform films on a moving web substrate. Here we explore two coating methods, gravure and slot die, to understand the impacts of each on film uniformity and performance.

30 DIRECT ENERGY CONVERSION↗

Roll-to-Roll Advanced Materials Manufacturing DOE Lab Consortium - FY16 Annual Report

A DOE laboratory consortium comprised of ORNL, ANL, NREL and LBNL, coordinating with Kodak’s Eastman Business Park (Kodak) and other selected industry partners, was formed to address enhancing battery electrode performance and R2R manufacturing challenges. The objective of the FY 2016 seed project was to develop a materials genome synthesis process amenable to R2R manufacturing and to provide modeling, simulation, processing, and manufacturing techniques that demonstrate the feasibility of process controls and scale-up potential for improved battery electrodes. The research efforts were to predict and measure changes and results in electrode morphology and performance based on process condition changes; to evaluate mixed, active, particle size deposition and drying for novel electrode materials; and to model various process condition changes and the resulting morphology and electrode performance.

36 MATERIALS SCIENCE↗

Reactive impinging-flow technique for polymer-electrolyte-fuel-cell electrode-defect detection

Reactive impinging flow (RIF) is a novel quality-control method for defect detection (i.e., reduction in Pt catalyst loading) in gas-diffusion electrodes (GDEs) on weblines. The technique uses infrared thermography to detect temperature of a nonflammable (<4% H 2 ) reactive mixture of H 2 /O 2 in N 2 impinging and reacting on a Pt catalytic surface. In this article, different GDE size defects (with catalyst-loading reductions of 25, 50, and 100%) are detected at various webline speeds (3.048 and 9.144 m min -1 ) and gas flowrates (32.5 or 50 standard L min -1 ). Furthermore, a model is developed and validated for the technique, and it is subsequently used to optimize operating conditions and explore the applicability of the technique to a range of defects. The model suggests that increased detection can be achieved by recting more of the impinging H 2 , which can be accomplished by placing blocking substrates on the top, bottom, or both of the GDE; placing a substrate on both results in a factor of four increase in the temperature differential, which is needed for smaller defect detection. Lastly, overall, the RIF technique is shown to be a promising route for in-line, high-speed, large-area detection of GDE defects on moving weblines.

30 DIRECT ENERGY CONVERSION↗

Defect Detection in Fuel Cell Gas Diffusion Electrodes Using Infrared Thermography

Polymer electrolyte membrane fuel cells are energy conversion devices that offer high power densities and high efficiencies for mobile and other applications. Successful introduction into the marketplace requires addressing cost barriers such as production volumes and platinum loading. For cost reduction, it is vital to minimize waste and maximize quality during the manufacturing of platinum-containing electrodes, including gas diffusion electrodes (GDEs). In this work, we report on developing a quality control diagnostic for GDEs, involving creating an ex situ exothermic reaction on the electrode surface and using infrared thermography to measure the resulting temperature profile. Experiments with a moving GDE containing created defects were conducted to demonstrate the applicability of the diagnostic for real-time web-line inspection.

30 DIRECT ENERGY CONVERSION↗

On-line, continuous monitoring in solar cell and fuel cell manufacturing using spectral reflectance imaging

A monitoring system 100 comprising a material transport system 104 providing for the transportation of a substantially planar material 102, 107 through the monitoring zone 103 of the monitoring system 100. The system 100 also includes a line camera 106 positioned to obtain multiple line images across a width of the material 102, 107 as it is transported through the monitoring zone 103. The system 100 further includes an illumination source 108 providing for the illumination of the material 102, 107 transported through the monitoring zone 103 such that light reflected in a direction normal to the substantially planar surface of the material 102, 107 is detected by the line camera 106. A data processing system 110 is also provided in digital communication with the line camera 106. The data processing system 110 is configured to receive data output from the line camera 106 and further configured to calculate and provide substantially contemporaneous information relating to a quality parameter of the material 102, 107. Also disclosed are methods of monitoring a quality parameter of a material.

14 SOLAR ENERGY↗

Manufacturing Readiness and Cost Impacts for PEM Stack and Balance of Plant

The results of two Manufacturing Readiness Assessments of PEM fuel cell stacks and material handling equipment (MHE) and backup power (BUP) PEM fuel cell systems are given. Design modifications of fuel cell systems were made because the initial, 2008 designs did not fully meet the operational requirements of the markets. This situation indicates the 2008 risk elements were overstated.For 2010 BUP and MHE fuel cell systems, manufacturers had not reached the Low Rate Initial Production (LRIP) defined in the 2008 MRA Report at 1,000 units per year per manufacturer.For fuel cell stacks, LRIP was demonstrated by more than one manufacturer.The federal tax incentive program has compensated for the initial high cost of fuel cell systems.The Balance-of-Plant (BOP) has not evolved as rapidly as the PEM fuel cell stack manufacturing readiness.The BOP in 2014 is as costly as the fuel cell stack for MHE applications.

30 DIRECT ENERGY CONVERSION↗

2010 Manufacturing Readiness Assessment Update to the 2008 Report for Fuel Cell Stacks and Systems for the Backup Power and Materials Handling Equipment Markets

In 2008, the National Renewable Energy Laboratory (NREL), under contract to the US Department of Energy (DOE), conducted a manufacturing readiness assessment (MRA) of fuel cell systems and fuel cell stacks for back-up power and material handling applications (MHE). To facilitate the MRA, manufacturing readiness levels (MRL) were defined that were based on the Technology Readiness Levels previously established by the US Department of Energy (DOE). NREL assessed the extensive existing hierarchy of MRLs developed by Department of Defense (DoD) and other Federal entities, and developed a MRL scale adapted to the needs of the Fuel Cell Technologies Program (FCTP) and to the status of the fuel cell industry. The MRL ranking of a fuel cell manufacturing facility increases as the manufacturing capability transitions from laboratory prototype development through Low Rate Initial Production to Full Rate Production. DOE can use MRLs to address the economic and institutional risks associated with a ramp-up in polymer electrolyte membrane (PEM) fuel cell production. In 2010, NREL updated this assessment, including additional manufacturers, an assessment of market developments since the original report, and a comparison of MRLs between 2008 and 2010.

08 HYDROGEN↗