Search NASA⌕ Search

Engineering topics

Um, Evan

Publications and source records attributed to Um, Evan.

Utah FORGE: LBNL Reports on VEMP Electromagnetic Data Collection and Processing - 2024

This archive contains reports related to Vertical Electromagnetic Profiling (VEMP) tool data collection and processing at Utah FORGE in 2024. The first report describes LBNL's effort to collect electromagnetic geophysical data with the tool in well 78-32B and a downhole electrode in well 16A. The second report describes the final data acquisition and processing of the VEMP electromagnetic data collected at the Utah FORGE site in May of 2024. Also included are a noise analysis as well as a comparison of the data to numerical models. This was originally presented as a paper at the 2025 Stanford Geothermal Workshop.

15 GEOTHERMAL ENERGY↗

Wellbore integrity assessment with casing-based advanced sensing

Wellbore integrity is of paramount importance to subsurface resource extraction, energy storage 1 and waste disposal. After installation, well casing and cement are subject to mechanical stress due to near-well pressure changes and fluid induced corrosion. This is exacerbated for geothermal wells where produced fluid is at high temperature and corrosive. The current state-of-the-art technologies for wellbore integrity assessments are an array of cased hole logging tools. Wireline deployed acoustic, electromagnetic and mechanical tools are all available to inspect steel casing corrosion and casing-cement bond and these tools can provide high-resolution assessment of borehole conditions. They are intrusive, however, in terms of borehole preparation and interruption to the normal operation of the wells, and not suitable for high temperature or highly deviated well deployments. In addition, these measurements are performed infrequently due to high cost, and are therefore incapable of providing frequent data to better predict borehole degradation trajectory, which can help provide early warning of potential borehole failures. For this project we are developing a suite of novel, non-invasive, casing based tools for wellbore integrity assessment, combining fast/low cost screening with higher-precision investigation. Our approach is based on monitoring the response of the casing when energized at the wellhead, thereby interrogating the casing without well intervention. Lab, field and numerical approaches are used in our study. During the early stage of the research, we focus on numerical simulations, which have shown the sensitivity of the low frequency electromagnetic (EM) signals to changes in borehole depths and have successfully tested the concept at a field site with different length well casings. Initial seismic modeling efforts have also demonstrated our capability to simulate seismic tube wave and seismic field alterations due to borehole breakage and associated fluid leakage. Further numerical, laboratory and field experiments are underway for additional technology sensitivity analysis, particularly the transient EM/Seismic reflectometry methods, data acquisition optimization, and numerical simulation improvements.

Wilt, Michael↗

The effects of well damage and completion designs on geoelectrical responses in mature wellbore environments

Well integrity is one of the major concerns in long-term geologic storage sites due to the potential risk of well leakage and groundwater contamination. Evaluating changes in electrical responses due to energized steel-cased wells has the potential to quantify and predict possible wellbore failures because any kind of breakage or corrosion along highly conductive well casings will have an impact on the distribution of the subsurface electrical potential. However, realistic wellbore-geoelectrical models that can fully capture fine-scale details of well completion design and the state of well damage at the field scale require extensive computational effort, or they can even be intractable to simulate. To overcome this computational burden while still keeping the model realistic, we have used the hierarchical finite-element method that represents electrical conductivity at each dimensional component (1D edges, 2D planes, and 3D cells) of a tetrahedral mesh. This allows well completion designs with real-life geometric scales and well systems with realistic, detailed, progressive corrosion and damage in our models. We have developed a comparison of possible discretization approaches of a multicasing completion design in the finite-element model. The effects of the surface casing and the coupling between concentric well casings as well as the effects of the degree and the location of well damage on the electrical responses are also examined. As a result, we analyze real surface electric field data to detect wellbore integrity failure associated with damage.

58 GEOSCIENCES↗

Casing-integrity mapping using top-casing electrodes and surface based EM fields

Wellbore integrity is of paramount importance to subsurface resource extraction, energy storage and hazardous waste disposal. We introduce a simple non-invasive technology for casing integrity screening, based on the continuity of electrical current flow. Applying low frequency current to a wellhead, with a distant return electrode, produces a casing current dependent on the properties and depth extent of the well casing as well as the background formation. These currents in-turn generate surface electrical fields that can be captured in a radial profile and be used to analyze properties of the well casing. Numerical modeling results reveal a strong relation of the electric field to the casing properties and depth extent of the well. A small breakage in the casing produces a profile coincident to a cased well with a completion depth above the break. A corroded patch, where the casing conductivity is reduced, also alters the field profiles and its depth may be estimated by comparing to the profile expected from the well completion diagrams. The electric field profiles are also strongly dependent on background resistivity distributions and on whether the well was drilled using water or oil-based drilling fluids. We validate the proof of concept in a field experiment, where we applied currents at the wellheads of two wells with different casing lengths. The two profiles were similar in appearance but offset in amplitude by more than a factor of 5, consistent with the theoretical analysis as well as the 3D modeling results. These results demonstrate that our proposed approach has promise for mapping the general casing condition without well intervention. This approach can be a practical and effective tool for rapidly screening a number of wells before expensive logging-based technologies are employed for casing inspection in detail.

58 GEOSCIENCES↗

Deep Controlled Source Electro-Magnetic Sensing: A Cost Effective, Long-Term Tool for Sequestration Monitoring

The proposed system was designed to operate as a permanent, autonomous monitoring and data collection system that can provide much higher temporal data density than can be achieved economically with 3-Dimensional (3D) seismic surveys. It can operate over broad areas for long periods of time providing full 3D data sets on a monthly basis at a very low cost. By borrowing techniques commonly used in marine CSEM, structural information from background seismic surveys can be incorporated into the CSEM modeling to provide high resolution models of CO 2 progression within reservoirs. The system uses borehole-based vertical-electric-dipole sources placed at reservoir depths in the formation. The electric and magnetic fields induced by this source are received on the surface using an array of stations. The project was conducted in three phases. Phase I demonstrated the feasibility of the system to collect static/reference data at the Ketzin CO 2 storage pilot site in Germany. In Phase I, numerical modeling was used to determine the optimal configurations and requirements for sensor sensitivity and data accuracy. Based on the model results, existing hardware and software were modified. The CSEM system was then field tested at the Ketzin site. The data were imaged and the results were compared with independent studies of the reservoir and overburden geo-electrical characteristics. Phase II demonstrated the ability to provide sensitive, cost-effective measurement of changes in reservoir properties and changes in the overlying formations using a second round of measurements at the Ketzin site. A prototype autonomous recording system was developed and tested as a subset of the measurement points. Phase III of the project quantified the advantages (and disadvantages) of the fully autonomous data collection subsystems by comparing them with repeated measurements made with mobile stations. The Phase III also provided an additional time point in measuring post-closure changes in and above the Ketzin CO 2 injection site. Validation of the CSEM field survey results were completed using a method such as other alternative and available field site data.

58 GEOSCIENCES↗

Fracture Propagation, Fluid Flow, and Geomechanics of Water-Based Hydraulic Fracturing in Shale Gas Systems and Electromagnetic Geophysical Monitoring of Fluid Migration

We investigate fracture propagation induced by hydraulic fracturing with water injection, using numerical simulation. For rigorous, full 3D modeling, we employ a numerical method that can model failure resulting from tensile and shear stresses, dynamic nonlinear permeability, leak-off in all directions, and thermo-poro-mechanical effects with the double porosity approach. Our numerical results indicate that fracture propagation is not the same as propagation of the water front, because fracturing is governed by geomechanics, whereas water saturation is determined by fluid flow. At early times, the water saturation front is almost identical to the fracture tip, suggesting that the fracture is mostly filled with injected water. However, at late times, advance of the water front is retarded compared to fracture propagation, yielding a significant gap between the water front and the fracture top, which is filled with reservoir gas. We also find considerable leak-off of water to the reservoir. The inconsistency between the fracture volume and the volume of injected water cannot properly calculate the fracture length, when it is estimated based on the simple assumption that the fracture is fully saturated with injected water. As an example of flow-geomechanical responses, we identify pressure fluctuation under constant water injection, because hydraulic fracturing is itself a set of many failure processes, in which pressure consistently drops when failure occurs, but fluctuation decreases as the fracture length grows. We also study application of electromagnetic (EM) geophysical methods, because these methods are highly sensitive to changes in porosity and pore-fluid properties due to water injection into gas reservoirs. Employing a 3D finite-element EM geophysical simulator, we evaluate the sensitivity of the crosswell EM method for monitoring fluid movements in shaly reservoirs. For this sensitivity evaluation, reservoir models are generated through the coupled flow-geomechanical simulator and are transformed via a rock-physics model into electrical conductivity models. It is shown that anomalous conductivity distribution in the resulting models is closely related to injected water saturation, but not closely related to newly created unsaturated fractures. Our numerical modeling experiments demonstrate that the crosswell EM method can be highly sensitive to conductivity changes that directly indicate the migration pathways of the injected fluid. Accordingly, the EM method can serve as an effective monitoring tool for distribution of injected fluids (i.e., migration pathways) during hydraulic fracturing operations

02 PETROLEUM↗