Search NASA⌕ Search

Engineering topics

Unocic, Kinga

Publications and source records attributed to Unocic, Kinga.

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Controlling microstructure and B2 ordering kinetics in Fe–Al system through additive manufacturing

Multi-material fabrication between steel and aluminum is challenging because of the formation of several intermetallic phases. Embrittling B2 ordered intermetallics form in the steel rich side and are stable till about 60% of Al dilution in steel. In this work by using multi-length scale characterization coupled with integrated computational process and thermokinetic modeling, we show that the ordered B2 intermetallics in the steel rich side of the Fe–Al system forms via a nucleation and growth mechanism. The extent of B2 ordered intermetallics can be controlled by modifying the directed energy deposition-additive manufacturing (DED-AM) process parameters. Our findings lay the foundation for enabling fabrication of crack-free functionally graded compositions between the two alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Wire directed energy deposition of steel-aluminum structures using cold metal transfer process

In this study, a sharp transition from 316L stainless steel to 4043 aluminum alloy was fabricated using wire directed energy deposition (DED) via the cold metal transfer (CMT) process. The CMT process with its inherently low heat input, led to a significant reduction in intermetallic thickness at the bi-metallic interface compared to blown powder DED technique reported in the literature resulting in superior properties when compared to those of dissimilar steel-aluminum welds. Thermo-kinetic modeling confirmed that the intermetallic formation is through a classical nucleation and growth mechanism, and the fraction and thickness can be controlled by adjusting CMT process parameters to kinetically arrest or minimize the intermetallic formation. These findings underscore the efficacy of CMT-based wire DED for fabrication of steel-aluminum bi-metallic structures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing as a processing route for steel-aluminum bimetallic structures

Here we present results on the fabrication of steel-aluminum bi-metallic structures using directed energy deposition additive manufacturing. The challenges associated with the fabrication of a sharp transition from steel to aluminum are uncovered using ex-situ characterization techniques and thermo-mechanical modeling of the deposition process. It was found that the fabrication of a sharp steel-aluminum transition is challenging with extensive cracking observed at the interface. The cracking was attributed to the combined effect of residual stress development due to thermal expansion coefficient mismatch and the presence of ordered intermetallics with low ductility at the interface. Using a coupled thermodynamic and thermo-mechanical modeling approach, potential pathways to enable the fabrication of steel-aluminum bi-metallic structures using additive manufacturing are proposed. The results presented here can lay the foundation for future work on the fabrication of bi-metallic steel-aluminum structures using directed energy deposition.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Catalyst design to direct high-octane gasoline fuel properties for improved engine efficiency

The paraffin-to-olefin (P/O) ratio in gasoline fuel is a critical metric affecting fuel properties and engine efficiency. In the conversion of dimethyl ether (DME) to high-octane hydrocarbons over BEA zeolite catalysts, the P/O ratio can be controlled through catalyst design. Here, we report bimetallic catalysts that balance the net hydrogenation and dehydrogenation activity during DME homologation. The Cu-Zn/BEA catalyst exhibited greater relative dehydrogenation activity attributed to higher ionic site density, resulting in a lower P/O ratio (6.6) versus the benchmark Cu/BEA (9.4). The Cu-Ni/BEA catalyst exhibited increased hydrogenation due to reduced Ni species, resulting in a higher P/O ratio (19). The product fuel properties were estimated with an efficiency merit function and compared against finished gasolines and a typical alkylate blendstock. Merit values for the hydrocarbon product from all three BEA catalysts exceeded those of the comparison fuels (0–5.3), with the product from Cu-Zn/BEA exhibiting the highest merit value (9.7).

Catalyst design↗
DOE OSTI2021

Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C

The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of heterogeneous microstructure on the tensile and creep performances of cast Haynes 282 alloy

Precipitation-strengthened Ni-based superalloys are leading candidate materials for advanced ultra-supercritical (A-USC) plants with steam conditions up to 760 °C (1400 °F) and 35 MPa (5 ksi). This study evaluates representative specimens from a large casting of Haynes 282 to study the effect of microstructural heterogeneity on the mechanical behavior of this alloy. The tensile test results of cast Haynes 282 over the temperature range 20–816 °C exhibited lower tensile strength and ductility in comparison with the reference wrought Haynes 282. However, the creep rupture tests of the cast alloy below 704–788 °C and 190–431 MPa presented a similar stress-Larson-Miller parameter to that of the wrought material. Microstructural and dislocation characterizations using scanning electron microscopy, conventional transmission electron microscopy, and scanning transmission electron microscopy in conjunction with energy dispersive X-ray spectroscopy were performed to understand the microstructural evolution before and after the mechanical tests. The heterogeneous microstructures of the cast Haynes 282 material, including the coarse grains, potential casting defects, and a bimodal size distribution of γ' precipitates, were detrimental to the tensile behavior, whereas the coarse-scale grains had a positive effect on the creep performance because diffusional creep was the dominant creep mechanism.

tensile testing↗
DOE OSTI2021

Residual stresses and microstructure within Allvac 718Plus laser powder bed fusion bars

The residual stresses within Allvac 718Plus bars built using LBPF with different laser powers, speeds and table displacements were measured using diffraction and mechanical methods and modelled with the baseplate attached and then removed. The residual stress profiles within the bars from the top surface down through the bulk were all quite similar, becoming less tensile due to a strain hardening mechanism. Table displacement has the greatest impact on residual stress, decreasing with increasing displacement/powder layer thickness. There was good agreement amongst the modeling and measurements. The microstructures were examined and varied slightly with energy density with higher densities having larger grains and enhanced post solidification diffusion. We found energy density had minimal impact on the residuals stresses within the parameters to produce dense material.

36 MATERIALS SCIENCE↗